Aleratec 330104 User guide

Brand: Aleratec

Model: 330104

Type: User guide

SOFTWARE USER GUIDE

Aleratec

1:21 USB Flash Drive Copy Cruiser™

Part No. 330104

www.aleratec.com

Table of Contents

Introduction .......................................................................................1

Initial System Setup ................................................................................1

Using the USB Duplication Suite Software ....................................2

Main Menu ..............................................................................................2

Data Copy Only ...................................................................................... 3

Format Only ............................................................................................9

Format Then Data Copy .......................................................................14

Create Image File ..................................................................................20

Clone Image File ...................................................................................22

Drive Letter Management .....................................................................24

Technical Support ..........................................................................26

Technical Support FAX Back Form ...............................................27

www.aleratec.com

Introduction

Thank you for purchasing the 1:21 USB Flash Drive Copy Cruiser. Please

read this Software User Guide thoroughly before using this product.

Initial System Setup

Attach the Aleratec 1:21 USB Flash Drive Copy Cruiser to your 1.

computer using the High Speed USB 2.0 cable provided.

The green power LED will light, and the computer will recognize the 2.

device.

Press the ON/OFF switch to power up the Aleratec 1:21 USB Flash 3.

Drive Copy Cruiser (necessary for some jobs).

Start the USB Duplication Suite duplication software via the icon on 4.

your Desktop or in the Start menu under “All Programs.”

www.aleratec.com

Using the USB Duplication Suite Software

Main Menu

The USB Duplication Suite’s main menu offers six functions:

Data Copy Only1.

Format Only2.

Format Then Data Copy3.

Create Image File4.

Clone Image File5.

Drive Management6.

Choose the desired option from the drop down menu.

www.aleratec.com

Using the USB Duplication Suite Software

Data Copy Only

Use this function to copy the contents of a folder to one or more USB ash

drives. This function will overwrite any les/folders on the target device(s)

with the same name as the source les/folders.

Start by choosing Data Copy Only from the drop down menu.1.

On the same screen, click “Add Files” to copy individual les or “Add 2.

Folder” to copy an entire folder.

www.aleratec.com

Using the USB Duplication Suite Software

Data Copy Only - continued

If you wish to remove an added le or folder, select the item and click 3.

“Remove”. To clear the list of les/folders to add, click “Clear”.

If you wish to verify the source data is copied successfully, click to 4.

check the box next to “Verify Data”.

www.aleratec.com

Using the USB Duplication Suite Software

Once you have added all the les/folders you want to copy, click the 5.

tab at the top of the window named “Destination”.

Click to select each USB ash drive that you want to copy to. You can 6.

click the button with the green “+” symbol to select all drives or the

button with the red “-” symbol to deselect all drives. The button with

the blue arrow will refresh the current list of drives.

www.aleratec.com

Using the USB Duplication Suite Software

Data Copy Only - continued

The “Processes” counter displays how many concurrent processes you 7.

want to run at once. The more processes you choose the more drives

will be copied to simultaneously.

The “Copies” counter is the total number of copies you want to do. If 8.

the number of copies specied is more than the number of available

drive slots, the software will break up the job into multiple “rounds”,

requiring the user to switch in new cards after each round is completed.

www.aleratec.com

Using the USB Duplication Suite Software

Once the drives, processes, and copies are specied, the user may click 9.

“Start” to begin the duplication process.

Progress is displayed through messages in the log and in the progress 10.

bar. Also, the number of completed and rejected copies is displayed

underneath the output log.

www.aleratec.com

Using the USB Duplication Suite Software

Data Copy Only - continued

If the user wishes to cancel the duplication process at any time, just 11.

click “Cancel”.

www.aleratec.com

Using the USB Duplication Suite Software

Format Only

Format one or more USB ash drives with this command (FAT formatting

only). A volume label to identify the media is added at the same time.

Note: The “Add File” interface will be disabled since it is not used.

Start by clicking on “Format Only” from the drop down menu. 1.

Click on the “Destination” tab located at the top of the window.2.

www.aleratec.com

Using the USB Duplication Suite Software

Format Only - continued

Select the drives that you wish to format. You can click the button with 3.

the green “+” symbol to select all drives or the button with the red

“-” symbol to deselect all drives. The button with the blue arrow will

refresh the current list of drives.

You can specify a single label for each drive in the text box under 4.

“Enter Label”. If no label is specied, the label that the drive currently

has will be used.

www.aleratec.com

Using the USB Duplication Suite Software

The “Processes” counter displays how many concurrent processes you 5.

want to run at once. The more processes you choose the more drives

will be copied to simultaneously.

The “Copies” counter is the total number of copies you want to do. If 6.

the number of copies specied is more than the number of available

drive slots, the software will break up the job into multiple “rounds”,

requiring the user to switch in new cards after each round is completed.

www.aleratec.com

Using the USB Duplication Suite Software

Format Only - continued

Once the drives, processes, and copies are specied, the user may click 7.

“Start” to begin the duplication process.

Progress is displayed through messages in the log and in the progress 8.

bar. Also, the number of completed and rejected copies is displayed

underneath the output log.

www.aleratec.com

Using the USB Duplication Suite Software

If the user wishes to cancel the duplication process at any time, just 9.

click “Cancel”.

www.aleratec.com

Using the USB Duplication Suite Software

Format Then Data Copy

This function will format and then copy les/folders to one or more USB

ash drives. Any les/folders on the target device(s) with the same names as

any source les/folders will be overwritten.

Start by clicking on “Format Then Data Copy” from the drop down 1.

menu.

On the same screen, click “Add Files” to copy individual les or “Add 2.

Folder” to copy an entire folder.

www.aleratec.com

Using the USB Duplication Suite Software

If you wish to remove an added le or folder, select the item and click 3.

“Remove”. To clear the list of les/folders to add, click “Clear”.

If you wish to verify the source data is copied successfully, click to 4.

check the box next to “Verify Data”.

www.aleratec.com

Using the USB Duplication Suite Software

Format Then Data Copy - continued

Once you have added all the les/folders you want to copy, click the tab at 5.

the top of the window named “Destination”.

Select the drives that you wish to format. You can click the button with 6.

the green “+” symbol to select all drives or the button with the red

“-” symbol to deselect all drives. The button with the blue arrow will

refresh the current list of drives.

Page is loading ...

Aleratec 330104 User guide

Aleratec 330104 User guide

Aleratec 330104 User guide

Related papers