Axis Communications T8341-EUR User manual
- Category
- Motion detectors
- Type
- User manual
AXIST8341PIRMotionSensor
UserManual
AXIST8341PIRMotionSensor
TableofContents
Solutionoverview...........................................3
Productoverview...........................................4
HowtoaddadevicetoaZ-WaveNetwork......................5
HowtotesttheZ-Wavedevice................................6
HowtoprogramtheZ-Wavedevice............................7
Z-Waveconguration.......................................10
Troubleshooting............................................12
Specications..............................................13
2
AXIST8341PIRMotionSensor
Solutionoverview
Solutionoverview
ThedeviceisZ-Wave®enabledandfullycompatiblewithanyZ-Waveenablednetwork.ThedevicecanbesetupinaZ-Wave
networktocommunicatedirectlywithotherenddevicessuchaslightingcontrollers,ortoreportdirectlytoaZ-Wavecontrollerlike
theAXISM5065PTZNetworkCamera.
3
AXIST8341PIRMotionSensor
Productoverview
Productoverview
•PIRsensorwindow(LEDindicatorinside)
•Tamperswitch
4
AXIST8341PIRMotionSensor
HowtoaddadevicetoaZ-WaveNetwork
HowtoaddadevicetoaZ-WaveNetwork
Autoinclusion
ThemotionsensorsupportstheautoinclusionfeaturewhereitwillautomaticallyenterInclusionmodewhenrstpoweredup.
Thiswillalsoapplywhenpoweredupafterafactoryreset.
1.Useascrewdrivertodetachthebatterycover.
2.PuttheAXISM5065camera(orotherZ-Wavecontroller)intoinclusionmode.
3.Insert1CR1233Vbatteriesintothebatterycompartmentwiththecorrectpolarity.TheLEDonthedeviceshouldturnON
4.EnterPINnumberintotheZ-Wavecontroller.ThePINnumbercanbefoundonthedevice.Seewhereintheinstallation
guide.
5.TheinclusionprocessshouldbecompletedwhentheLEDstopsblinking
6.Performtestbeforeyouretthebatterycover.SeeHowtotesttheZ-WaveDevice.
Manualinclusion
YoucanalsochoosetomanuallyaddtheZ-Wavedevicetoacontroldevice.Pleasefollowthestepsdescribedbelow.
Note
Forbestresults,excludethedevicebeforestartingtheinclusionprocess.Formoredetailsseetheinstallationguide.
1.Useascrewdrivertodetachthebatterycover.
2.PuttheAXISM5065camera(orotherZ-Wavecontroller)intoinclusionmode.
3.Insert1CR1233Vbatteriesintothebatterycompartmentwiththecorrectpolarity.TheLEDonthedeviceshouldturnON
4.Pressthetamperswitch3timeswithin1.5secondstoputtheunitintolearning(inclusion/exclusion)mode.
5.EnterPINnumberintotheZ-Wavecontroller.ThePINnumbercanbefoundonthedevice.Seewhereintheinstallation
guide.
6.TheinclusionprocessshouldbecompletedwhentheLEDstopsblinking.
7.Performtestbeforeyouretthebatterycover.SeeHowtotesttheZ-WaveDevice.
Manualexclusion
1.Useascrewdrivertodetachthebatterycover.
2.Pressthetamperswitch3timeswithin1.5secondstoputtheunitintolearning(inclusion/exclusion)mode.
3.TheexclusionprocessshouldbecompletedwhentheLEDstopsblinking
4.Retthebatterycover.
5
AXIST8341PIRMotionSensor
HowtotesttheZ-Wavedevice
HowtotesttheZ-Wavedevice
Warm-up
Itwilltakethemotionsensorapproximately2minutestowarmupafterthebatteryisinserted.DuringthisperiodtheLEDbehindthe
lenswillturnon.WhentheredLEDturnsoff,thewarm-upprocedureiscompletedandthedeviceisreadytodetect.
•ThiswillnotaffecttheInclusion/Exclusionprocess.
•Afteryouremovethebatteries,wait5secondsbeforeyouretthem.
Quicktest
1.Ifthetamperswitchisnotpressedafterinclusion,thedevicewillenter“Testmode”toallowyoutotestthedevice
beforeitismountedonthewall.
2.Ifmovementisdetectedduring“Testmode”,theLEDonthemotionsensorwilllightuponceindicatingthattheunitis
workingproperly.Retriggertimeisabout5sec.
3.Toexit“Testmode”andenternormalmode,simplypressthetamperswitchformorethan10seconds.
4.WhenthePIRistriggeredduringnormalmodetheredLEDwillnotlightup,andretriggertimeisbasedonasetupvalue.
Note
Important!MakesureyouhavecreatedaZ-Wavecontroller-eventlinkedtothebattery-statussignal.Thatwayyouwill
getanoticationoraLEDindicationwhenadevicerunsonlowbatterypower.
6
AXIST8341PIRMotionSensor
HowtoprogramtheZ-Wavedevice
HowtoprogramtheZ-Wavedevice
Note
ProgrammingZ-WavedevicesusingaZ-Wavecontrollerisrecommendedforexperiencedusersonly.
Z-WaveGroup
ThedetectorsupportseitheroneoftwoZ-WaveAssociationGroups:
Group1:Associationwith1Controllernode.
Group2:Associationwith4nodes(i.e.enddevicessuchassmartplugsandotherlightingcontrollers).Thisallowsthedetectorto
transfercommandsdirectlytoenddeviceswithouttheparticipationofthecontroller.Thishastheeffectthatwhenthedetector
triggers,alldevicesassociatedwithdetectorwillbeoperated.
Note
Association-groupsupportcanvaryamongZ-WaveControllers.TheAXISM5065supportsZ-WaveAssociationGroup1.
Group1commands:
•WhenthedeviceispoweredupandalreadyisapartofaZ-Wavenetwork,theunitwillsendaNoticationReportto
thenodeinGroup1.
•Whenthedetectorsensesamovement,theunitwillsendaNoticationReporttothenodesofGroup1.Oncethe
movementisstopped,aNoticationReportwillbesentagaintoGroup1.
•Whenthedetector’sstatusischanged,thedevicewillcheckitsbatterystatussimultaneously.Ifthebatteryleveldropsto
anunacceptablelevel,thedevicewillemitaBatteryreporttothenodesofGroup1.
•WhenyouperformaFactoryReset,theunitwillsendDeviceResetLocallyNoticationtothenodeofGroup1.
Group2commands:
•Whenthedetectoristriggered,theunitwillsendBASIC_SETcommandwhichcontainsavaluetothenodesofGroup2.
Z-WavePlus® ®
®info
RoletypeNodetypeInstallerIconUserIcon
SlaveSleepingreportZ-WavePlusnodeSensorNoticationDeviceType
(HomeSecurity)
SensorNoticationDeviceType
(HomeSecurity)
Version
Protocollibrary3(Slave_Enhance_232_Library)
Protocolversion4.3D(6.71.01)
Manufacturer
ManufacturerIDProductTypeProductID
0x03640x00020x0001
AGI(AssociationGroupInformation)table
7
AXIST8341PIRMotionSensor
HowtoprogramtheZ-Wavedevice
GroupProleCommandClass&Command
(List)Nbytes
GroupName(UTF-8)
1GeneralBatteryReport
NoticationReport
DeviceResetLocallyNotication
Lifeline
2ControlBasicSetPIRControl
Notication
EventTypeEventEventParameters
Length
EventParameters
Powerisappliedforthersttime0x080x01Null
PIRTriggerON0x070x08Null
PIRTriggerOFF0x070x000x010x08
Tamperswitchpressedmore
than10seconds
0x070x000x010x03
Tamperswitchpressedmore
than10secondsandreleased
0x070x03Null
Battery
BatteryReport(value)Description
20～100BatteryLevel(%)
0xFFLowBattery
Commandclasses
Thisproductsupportsthefollowingcommandclasses:
•COMMAND_CLASS_ZWAVEPLUS_INFO_V2
•COMMAND_CLASS_ASSOCIATION_V2
•COMMAND_CLASS_ASSOCIATION_GRP_INFO
•COMMAND_CLASS_TRANSPORT_SERVICE_V2
•COMMAND_CLASS_VERSION_V2
•COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
•COMMAND_CLASS_DEVICE_RESET_LOCALLY
•COMMAND_CLASS_POWERLEVEL
•COMMAND_CLASS_SECURITY
•COMMAND_CLASS_SECURITY_2
•COMMAND_CLASS_SUPERVISION
•COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4
•COMMAND_CLASS_BATTERY
•COMMAND_CLASS_WAKE_UP_V2
8
AXIST8341PIRMotionSensor
HowtoprogramtheZ-Wavedevice
•COMMAND_CLASS_NOTIFICATION_V4
•COMMAND_CLASS_CONFIGURATION
Wakeupcommandclass
AfterthedetectorhasbeenincludedintoaZ-Wavenetworkitwillgotosleep,butitwillsendawake-upnoticationcommand
tothecontrollerperiodicallyatapresetperiod.Themotiondetectorwillstayawakeforatleast10secondsandthengobackto
sleeptoconservebatterylife.
Thetimeintervalbetweenwakeupnoticationcommandscanbesetinthewakeupcommandclassbasedontherangevaluesbelow:
Minimumwakeupinterval600s(10minutes)
Maximumwakeupinterval86400s(1day)
Defaultwakeupinterval14400s(4hours)
Wakeupintervalstepseconds600s(10minutes)
9
AXIST8341PIRMotionSensor
Z-Waveconfiguration
Z-Waveconfiguration
ThefollowinginformationisforsomeonethathassomeexperienceinsettingupaZ-Wavesystem,orsomeonethathascomputer
softwarerunningaZ-Wavecontroller.PleasegetfamiliarwiththesoftwareoftheZ-Wavecontrollerbeforegettingstarted.
Tominimizepowerconsumptionofthebattery,RFonthedeviceisswitchedoffasdefault.Inordertostartthesetupprocess,please
pressthetamperswitchoncetoturnontheRFpowerfor30seconds.YoucanthenseetheLEDstarttoblinkeverysecond.Ifsetup
isnotnishedwithin30seconds,pleasepressthetamperswitchonemoretimetocontinuethesetup
•Basicsetlevel
WhenaBasicSetCommandissentandcontainsavalue,thereceiverwillprocessit.Forexample,alampmodulewould
receiveaBasicSetcommandwhichdeterminesthedimlevel.
Example:
1-99:ON(BinarySwitchDevice)
DimLevel(MultilevelSwitchDevice)
FunctionParameternumberSizeRangeDefault
BasicSetlevel111~9999
•Sensitivitylevel(PIRsensoronly)
Foroptimalefciency,itisrecommendedtotestthedetector’sresponsetomovementsfromthefarthestendofthe
coverageareawhenyouuseitforthersttime.Ifmovementscannotbedetectedaccurately,simplyadjustthesensitivity
levelwiththeCongurationParameter#3.Thisparametercanbeconguredwithavaluefrom1to10,where1means
lowsensitivityand10meanshighestsensitivity.
FunctionParameternumberSizeRangeDefault
Sensitivitylevel311~106
•Re-triggerintervalsetting(PIRsensoronly)
Thecongurationparameterusedtoadjustthere-triggerintervalafterthedetectorhasbeentriggeredasconguration
parameter#4.Noresponsewillbemadeduringthisintervalifamovementisdetected.Thetimeintervalcanbeset
between5secondsto3,600seconds.
FunctionParameternumberSizeRangeDefault
Retriggerinterval425~3600(sec)180
•Luxlevel
Youcansetapercentagefortheluxlevelwhichdetermineswhenthelightsensorwillbeactivated.Iftheambient
illuminationdropsbelowthesetpercentage,andapersonmovesacrossorwithintheprotectedarea,thedetectorwill
emitaZ-WaveONcommand(i.e.BasicSetcommand(Value=BasicSetLevel))tothecontrollerandactivateconnected
modulesandlighting.Thepercentagecanbesetbetween1%to100%.
FunctionParameternumberSizeRangeDefault
Luxlevel511~100%20
On-offduration
Theon-offdurationsettingcanbeusefulifthedetectorisconnectedtoamoduleorlighting.Thedurationdetermineshowlongthe
module/lightingshouldstayON.Forinstance,aLampModuleturnsoff100secsafterithasbeenturnedon.Thedurationcanbe
conguredtolastbetween5to3600seconds.
10
AXIST8341PIRMotionSensor
Z-Waveconfiguration
FunctionParameternumberSizeRangeDefault
On-OffDuration625~3600(sec)15
1 1
AXIST8341PIRMotionSensor
Troubleshooting
Troubleshooting
Ifyoucan’tndwhatyou’relookingforhere,trythetroubleshootingsectionataxis.com/support
ThetablebelowexplainsthestatusintheZ-WavecontrolleraswellastheLEDindicationonthedevice.
Action/StatusDescriptionLEDindication
NonodeIDTheZ-Wavecontrollercouldnotndthedevice
anddidnotprovideanodeID.
2-secondon,2-secondofffor2minutes.
1.Pressthetamperswitch3timeswithin1.5
secondstoputthedeviceintoexclusionmode.
2.Within1secondofstep1,pressthetamper
switchagainandholduntilLEDisoff(about
5seconds).
FactoryReset
(Thisprocedureshould
onlybeusedwhen
thecontrollerisnot
responding.)
3.NodeIDisexcluded.Thedevicereverts
tofactorydefaultstateandwillbein
auto-inclusionmodefor4minutes.
2-secondon,2-secondofffor2minutes.
Failedorsuccessfulresultsinincluding/excludingtheIDcanbeviewedonaZ-Wavecontroller.
Tablebelowliststypicalproblemsencountered:
SymptomPossiblecauseRecommendation
Cannotcarryoutinclusion
andassociation.
1.Thedeviceisstillconnected,orhas
beenaccidentallyincluded,toaprevious
network.
2.TheenteredPINcodeisincorrect
3.Thebatteryhasrunoutofpower.
4.Batterypolarityisreversed.
5.Detectorismalfunctioning.
1.Excludethedevicebefore
includingitagain.
2.Makesureyouhaveentered
thecorrectPINcode
3.Replacethebattery.
4.Retthebatterywiththe
correctpolarity.
5.Ensurethedetectorisworking
properly.
Cannotcontrolthe
connectedmodules.
1.Thedeviceisstillconnected,orhas
beenaccidentallyincluded,toaprevious
network.
2.Thebatteryhasrunoutofpower.
3.Detectorismalfunctioning.
1.Excludethedevicebefore
includingitagain.
2.Replacethebattery.
3.Ensurethedetectorisworking
properly.
Thedetectorisnot
functioningproperly.
1.Thedeviceisstillconnected,orhas
beenaccidentallyincluded,toaprevious
network.
2.Thebatteryhasrunoutofpower.
3.Thedetectorismountedabovearadiator
orheater.
4.Detectorismalfunctioning.
1.Excludethedevicebefore
includingitagain.
2.Replacethebattery.
3.Removethesourceof
interferenceorreposition
itsmountinglocation.
4.Ensurethedetectorisworking
properly.
Theeventlistisnotworking
properly.
1.Thedeviceisstillconnected,orhas
beenaccidentallyincluded,toaprevious
network.
2.Thecontroller’srmwareisoutdated.
3.Thebatteryhasrunoutofpower.
1.Excludethedevicebefore
includingitagain.
2.Makesurethecontrollerhas
thelatestrmware
3.Replacethebattery.
Note
Forbestresults,excludethedevicebeforestartingtheinclusionprocess.Formoredetailsseetheinstallationguide.
12
AXIST8341PIRMotionSensor
Specifications
Specifications
Tondthelatestversionoftheproduct’sdatasheet,gototheproductpageataxis.comandlocateSupport&Documentation.
Specications
BatteryCR1233.0VLithiumBattery
Batterylife1year*
RangeUpto100m(328ft)lineofsight
Warm-uptimeAbout2minutes
PIRdetectioncoverageUpto10m(33ft)x1 10°(at1.8m(5.9ft)mountingheight&25°C(77°F)
Operatingfrequency908.42MHz(US,922.5MHz(JP),868.42MHz(EU)
FCCIDFU5SP817
Specicationsaresubjecttochangewithoutnotice
*measuredat10triggersperday
13
UserManualVer.M2.1
AXIST8341PIRMotionSensorDate:September2018
©AxisCommunicationsAB,2017-2018PartNo.T101 17079
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
Axis Communications T8341-EUR User manual
- Category
- Motion detectors
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
