Aruba JL586A Reference guide

Type
Reference guide

This manual is also suitable for

About the HPE FlexFabric 5710
Command References
Software version: Release 671x and later
Document version: 6W100-20230822
© Copyright 2023 Hewlett Packard Enterprise Development LP
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard
Enterprise products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett
Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or
copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software
Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s
standard commercial license.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard
Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise
website.
Acknowledgments
Intel®, Itanium®, Pentium®, Intel Inside®, and the Intel Inside logo are trademarks of Intel Corporation in the
United States and other countries.
Microsoft® and Windows® are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Adobe® and Acrobat® are trademarks of Adobe Systems Incorporated.
Java and Oracle are registered trademarks of Oracle and/or its affiliates.
UNIX® is a registered trademark of The Open Group.
About the HPE FlexFabric 5710 command
references
The HPE FlexFabric 5710 command references describe the commands and command syntax
options available for the HPE FlexFabric 5710 Switch Series.
Command reference
Content
Fundamentals Command
Reference
Covers the commands for logging in to and setting up the device.
This command reference includes:
CLI (command privilege settings and CLI management commands).
RBAC.
Logging in to the switch.
FTP and TFTP.
File system management.
Configuration file management.
Software upgrade.
ISSU.
GIR.
Emergency shell.
Preprovisioning.
Device management.
Tcl.
Python.
Virtual Technologies Command
Reference Covers the commands for configuring an IRF fabric.
Layer 2LAN Switching
Command Reference
Covers the commands for configuring Layer 2 technologies and features
in a LAN switched network.
This command reference includes:
MAC address table and MAC Information.
Bulk interface configuration.
Ethernet interface.
Ethernet link aggregation.
DRNI.
Port isolation.
VLAN (including VLAN, super VLAN, private VLAN, and voice
VLAN).
MVRP.
Loopback, null, and inloopback interfaces.
QinQ.
VLAN mapping.
Spanning tree.
Loop detection.
LLDP.
L2PT.
Service loopback group.
Layer 2 forwarding.
Command reference
Content
Layer 3IP Services
Command Reference
Covers the commands for configuring and managing IP addressing
(including static and dynamic IPv4 and IPv6 address assignment),
network performance optimization, ARP, and interoperation between IPv4
and IPv6.
This command reference includes:
ARP (including ARP, gratuitous ARP, proxy ARP, ARP snooping,
ARP fast reply, and ARP direct route advertisement).
IP addressing.
DHCP.
DNS and DDNS.
Basic IP forwarding and load sharing.
Fast forwarding.
Adjacency table.
IRDP.
IP performance optimization.
UDP helper.
IPv6 basics.
DHCPv6.
IPv6 fast forwarding.
Tunneling.
GRE.
HTTP redirect.
Layer 3IP Routing Command
Reference
Covers the commands for configuring routes for IPv4 and IPv6 networks
of different sizes, route filtering, route control, and policy based routing.
This command reference includes:
Basic IP routing.
Static routing.
RIP.
OSPF.
IS-IS.
BGP.
Policy-based routing.
IPv6 static routing.
RIPng.
OSPFv3.
IPv6 policy-based routing.
Routing policy.
DCN.
Command reference
Content
IP Multicast Command
Reference
Covers the commands for Layer 2 and Layer 3 multicast protocols.
This command reference includes:
IGMP snooping.
PIM snooping.
Multicast VLAN.
Multicast routing and forwarding.
IGMP.
PIM.
MSDP.
Multicast VPN.
MLD snooping.
IPv6 PIM snooping.
IPv6 multicast VLAN.
IPv6 multicast routing and forwarding.
MLD.
IPv6 PIM.
ACL and QoS Command
Reference
Covers the commands for classifying traffic with ACLs, and allocating
network resources and managing congestions with QoS technologies to
improve network performance and network use efficiency.
This command reference includes:
ACL.
QoS (including QoS policy, priority mapping, GTS and rate limit,
congestion management, congestion avoidance, and global CAR).
Time range.
Data buffer.
QCN.
Command reference
Content
Security Command Reference
Covers security feature commands. Available security features include
identity authentication (AAA and PKI), access security (802.1X, MAC
authentication, portal, and port security), secure management (public key
management, SSH, SSL, and IPsec), and attack protection (IP source
guard, ARP attack protection, uRPF, attack detection and prevention, and
ND attack defense).
This command reference includes:
AAA.
802.1X.
MAC authentication.
Portal.
Web authentication.
Port security.
User profile.
Password control.
Keychain.
Public key management.
PKI.
SSH.
SSL.
Object group.
Attack detection and prevention.
TCP attack prevention.
IP source guard.
ARP attack protection.
ND attack defense.
uRPF.
SAVI
SAVA
MFF.
Crypto engine.
FIPS.
High Availability Command
Reference
Covers high availability commands for managing failure detection and
failover. Failure detection technologies focus on fault detection and
isolation. Failover technologies focus on network recovery.
This command reference includes:
Ethernet OAM.
CFD.
DLDP.
RRPP.
ERPS.
Smart Link.
Monitor Link.
VRRP.
BFD.
Track.
Process placement.
Command reference
Content
Network Management and
Monitoring Command
Reference
Covers the commands that help you manage and monitor your network,
for example, manage system events, collect traffic statistics, sample
packets, assess network performance, and test network connectivity.
This command reference includes:
System maintenance and debugging (ping, tracert, and system
debugging).
NQA.
NTP and SNTP.
PTP
SNMP.
RMON.
Event MIB.
NETCONF.
CWMP.
EAA.
Process monitoring and maintenance.
Mirroring (including both port and traffic mirroring).
sFlow.
Information center.
Packet capture.
VCF fabric.
Performance management.
Telemetry Command
Reference Covers the commands for configuring gRPC.
OpenFlow Command
Reference Covers the commands for configuring OpenFlow.
VXLAN Command Reference Covers the commands for configuring VXLAN.
Intelligent Lossless Network
Command Reference Covers the commands for configuring PFC.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Aruba JL586A Reference guide

Type
Reference guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI