CyberData 011187 Operations Guide

Brand: CyberData

Model: 011187

Category: Network switches

Type: Operations Guide

CyberData 011187 is a 2-Port PoE Gigabit Switch that provides both power and data over a single Ethernet cable. It is fully compliant with the IEEE 802.3af/at standard, making it compatible with a wide range of PoE devices. The switch has one Power Device (PD) input port and two Power Source Equipment (PSE) output ports. The PD input port can receive power from either an 802.3af or 802.3at PoE injector, while the PSE output ports can provide power to two PoE-powered devices.

The switch also supports 10/100/1000Mbps data rates, making it suitable for use in high-speed networks.

2-Port PoE Gigabit Switch



Operations Guide

Part #011187

Document Part #930591G

for Firmware Version 1.0.0

CyberData Corporation

3 Justin Court

Monterey, CA 93940

(831) 373-2601

The IP Endpoint Company

CyberData Corporation 930591G Operations Guide

2-Port PoE Gigabit Switch Operations Guide 930591G

Part # 011187

This manual and related materials are the copyrighted property of CyberData Corporation. No part of

this manual or related materials may be reproduced or transmitted, in any form or by any means

(except for internal use by licensed customers), without prior express written permission of

CyberData Corporation. This manual, and the products, software, firmware, and/or hardware

described in this manual are the property of CyberData Corporation, provided under the terms of an

agreement between CyberData Corporation and recipient of this manual, and their use is subject to

that agreement and its terms.

DISCLAIMER: Except as expressly and specifically stated in a written agreement executed by

CyberData Corporation, CyberData Corporation makes no representation or warranty, express or

implied, including any warranty or merchantability or fitness for any purpose, with respect to this

manual or the products, software, firmware, and/or hardware described herein, and CyberData

Corporation assumes no liability for damages or claims resulting from any use of this manual or such

products, software, firmware, and/or hardware. CyberData Corporation reserves the right to make

changes, without notice, to this manual and to any such product, software, firmware, and/or

hardware.

OPEN SOURCE STATEMENT: Certain software components included in CyberData products are

subject to the GNU General Public License (GPL) and Lesser GNU General Public License (LGPL)

“open source” or “free software” licenses. Some of this Open Source Software may be owned by third

parties. Open Source Software is not subject to the terms and conditions of the CyberData

Source Software is determined by the terms of the GPL, LGPL, or third party, according to who

licenses that software.

Software or firmware developed by CyberData that is unrelated to Open Source Software is

copyrighted by CyberData, subject to the terms of CyberData licenses, and may not be copied,

modified, reverse-engineered, or otherwise altered without explicit written permission from

CyberData Corporation.

TRADEMARK NOTICE: CyberData Corporation and the CyberData Corporation logos are

trademarks of CyberData Corporation. Other product names, trademarks, and service marks may be

the trademarks or registered trademarks of their respective owners.

Technical Support 



The fastest way to get technical support for your VoIP product is to

submit a VoIP Technical Support form at the following website:

http://support.cyberdata.net/



Phone: (831) 373-2601, Ext. 333

Email: [email protected]

Fax: (831) 373-4193

Company and product information is at www.cyberdata.net.

The IP Endpoint Company

Operations Guide 930591G CyberData Corporation

Revision Information

Revision 930591G, which corresponds to design version 1.0.0, was released on March 19, 2021,

and has the following changes:

• Adds Section 1.1, "How to Identify This Product".

• Updates Section 1.2, "Features".

• Updates Section 1.3, "Specifications".

• Updates Section 1.4, "Compliance".

• Adds Chapter 2, “Installing the 2-Port PoE Gigabit Switch.

• Updates Figure 4, "Typical Installation of the 2-Port PoE Gigabit Switch"

CyberData Corporation 930591G Operations Guide

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

9. Only use attachments/accessories specified by the manufacturer.

10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been

spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

11. Prior to installation, consult local building and electrical code requirements.

CyberData Corporation 930591G Operations Guide

Pictorial Alert Icons

Hazard Levels

Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or

serious injury. This is limited to the most extreme situations.

Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or

serious injury.

Caution: Indicates a potentially hazardous situation which, if not avoided, could result in minor or

moderate injury. It may also alert users against unsafe practices.

Notice: Indicates a statement of company policy (that is, a safety policy or protection of property).

The safety guidelines for the equipment in this manual do not purport to address all the safety issues

of the equipment. It is the responsibility of the user to establish appropriate safety, ergonomic, and

health practices and determine the applicability of regulatory limitations prior to use. Potential safety

hazards are identified in this manual through the use of words Danger, Warning, and Caution, the

specific hazard type, and pictorial alert icons.

General Alert

This pictoral alert indicates a potentially hazardous situation. This alert will be

followed by a hazard level heading and more specific information about the

hazard.

Ground

This pictoral alert indicates the Earth grounding connection point.

GENERAL ALERT

Operations Guide 930591G CyberData Corporation

Contents

Chapter 1 Product Overview 1

1.1 How to Identify This Product .................................................................... 1

1.2 Features .................................................................................................. 2

1.3 Specifications .......................................................................................... 3

1.4 Compliance .............................................................................................. 4

1.4.1 CE Statement ......................................................................................................... 4

1.4.2 FCC Statement ....................................................................................................... 4

Chapter 2 Installing the 2-Port PoE Gigabit Switch 5

2.1 Checklist .................................................................................................. 5

2.2 Installation ............................................................................................... 5

2.2.1 Installation Method ................................................................................................. 5

2.2.2 Desktop or Shelf Installation ................................................................................... 5

2.3 Powering on the 2-Port PoE Gigabit Switch ............................................ 6

2.3.1 How the Input Power is Distributed ........................................................................ 6

2.4 Network Connection ................................................................................ 7

Appendix A The Standard RJ-45 Introduction 8

A.1 The Standard Cable, RJ-45 Pin Assignment .......................................... 9

Appendix B Mounting 10

B.1 Dimensions and Mounting Hole Measurements ................................... 10

B.2 Mounting Option .................................................................................... 11

Appendix C Typical Installation 12

C.1 Example ................................................................................................ 12

Operations Guide 930591G CyberData Corporation

1 Product Overview

1.1 How to Identify This Product

To identify the 2-Port PoE Gigabit Switch, look for a product label similar to the one shown in

Figure 1-1. Confirm the following:

• The part number on the label should be 011187.

• The serial number on the label should begin with 187.

Figure 1-1. Product Label

OUT1 OUT2 IN

The IP Endpoint Company

2 Port Gigabit with

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

SN:

802.3at Class 4 Type 2802.3at Class 0 Type 1

[email protected] MAX[email protected] MAX

PSE PSE PD

Link/ActPwr Link/ActPwr Link/ActPwr

PoE Power Splitter

187100001

PN:011187B

CyberData Corporation

www.cyberdata.net

Serial number begins with 187The part number on the label should be 011187

Product Overview

Features

Operations Guide 930591G CyberData Corporation

1.2 Features

Power

• Fully compliant to IEEE 802.3af/at standard

• 1 Power Device (PD) input port 802.3af or 802.3at

• 2 Power Source Equipment (PSE) output ports 802.3af or 802.3at (limited PD input)

Data

• All ports are 10/100/1000Mbps (10BASE-T, 100BASE-TX, 1000BASE-T) auto sensing based

upon the port's individual connection

• Each port has auto MDI-X

• 802.11q VLAN tagging

• Automatic address learning, address aging and address migration

• Supports 9216-byte jumbo frame length

Notification

• Link/Status and connection speed LEDs

Product Overview

Specifications

Operations Guide 930591G CyberData Corporation

1.3 Specifications

Specifications

Ethernet I/F 10/100/1000 Mbps, Auto MDI-X, RJ45

Power Distribution

Input

Internal Circuit Use

Output

PD input up to 30W:

802.3af @ 15W

802.3at @ 25W

Generic PoE Injector up to 30W

Power available to share between two PSE outputs:

13W with 802.3af input

23W with 802.3at input

28W with generic 30W PoE injector input

Operating Range Temperature: -40

C to 55

C (-40

F to 131

F)

Humidity: 5-95%, non-condensing

Storage Temperature

Storage Altitude

-40

C to 70

C (-40

F to 158

Up to 15,000 ft. (4573 m)

Dimensions

5.31 inches [134.8 millimeter] Length

3.03 inches [76.9 millimeter] Width

1.06 inches [26.9 millimeter] Height

Weight

Boxed Weight

0.56 lbs [0.25 kg]

1.0 lbs [0.54 kg]

Compliance CE: EMC Directive – Class A EN 55032 & EN 55035, LV Safety Directive

– EN 62368-1; RoHS Compliant; FCC P

art 15 Class A; IEEE 802.3 Compliant

Part Number 011187

Table 1-1. Specifications

a. Either one or both of the PSE outputs can provide PoE power as long as the overall PSE output wattage is 2W less

than the PD input.

b. Dimensions are measured from the perspective of the product being upright with the front of the product facing you.

Product Overview

Compliance

Operations Guide 930591G CyberData Corporation

1.4 Compliance

1.4.1 CE Statement

As of the date of manufacture, this product has been tested and found to comply with the

specifications for CE marking and standards per EMC and Radiocommunications Compliance.

EMC Directive - Class A Emissions, Immunity, and LV Safety Directive, RoHS Compliant.

Flammability rating on all components is 94V-0.

1.4.2 FCC Statement

This equipment has been tested and found to comply with the limits for

a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for

compliance could void the user's authority to operate the equipment.



Operations Guide 930591G CyberData Corporation

2 Installing the 2-Port PoE Gigabit Switch

2.1 Checklist

Before you start installing your equipment, verify that the package contains the following:

• The 2-Port PoE Gigabit Switch

• The 2-Port PoE Gigabit Switch Quick-Reference Placemat

Please notify your supplier immediately if any of the previously items are missing or damaged.

2.2 Installation

2.2.1 Installation Method

The site where you install the switch may greatly affect its performance. When installing, please take

the following into consideration.

• Install the switch in a cool, dry place. See technical specifications for the acceptable

temperature and humidity operating ranges.

• Install the switch on a secure, level surface that can support its weight (at least 1Kg).

Alternatively, the switch can be applied to any smooth dry surface using furnished stick-on tape.

• Leave at least 10cm of space at the front and rear of the switch to ensure adequate ventilation.

2.2.2 Desktop or Shelf Installation

When installing the switch on a shelf on desktop, make sure that the previously mentioned

guidelines in

Section 2.2.1, "Installation Method" are followed for adequate ventilation.

Installing the 2-Port PoE Gigabit Switch

Powering on the 2-Port PoE Gigabit Switch

Operations Guide 930591G CyberData Corporation

2.3 Powering on the 2-Port PoE Gigabit Switch

The switch is powered by your existing central POE Switch. No additional power supply is required.

Simply plug your cable from your central POE switch into the PD port of the switch and your switch

will power on for use.

Figure 2. Front Panel of the 2-Port PoE Gigabit Switch

2.3.1 How the Input Power is Distributed

• The PD input can be up to 30W.

• A 802.3af source @ 15W

• A 802.3at source @ 25W

• A generic PoE injector up to 30W

• The internal circuits on the splitter takes 2W to operate.

• With an 802.3af input, 13W are available to share between the two PSE outputs.

• With an 802.3at input, 23W are available to share between the two PSE outputs.

• With a generic 30W PoE injector, 28W are available to share between the two PSE outputs.

Link / Activity (green)

PSE-1 Power ON (yellow) PSE-2 Power ON (yellow) PD Power ON (yellow)

Table 2. Powering on the 2-Port PoE Gigabit Switch

LED Status Description

PD (Orange) ON Switch has a connection from the PD port to the PSE device.

Power has been successfully applied.

OFF Connection to the PSE device is not present. 

No power has been applied to the switch.

PSE (Orange) ON PD device such as IP phone is connected to the port and

drawing power.

OFF PD device is not connected or no power is being drawn from

the switch.

Link/Act (Green) ON

A valid link

established.

Blink Traffic is present on port.

OFF

link

has been established.

Installing the 2-Port PoE Gigabit Switch

Network Connection

Operations Guide 930591G CyberData Corporation

2.4 Network Connection

Figure 3. Front Panel of 2-Port PoE Gigabit Switch

Connect your devices (computer, router, switch, IP Phone, Wireless Access Point, IP Camera etc.) to

the ports with a CAT-5/CAT-5e/CAT-6 network cable. Since the switch supports Auto MDI/MDI-X, you

can use either a straight through or cross-over network cable.

Figure 4. Typical Installation of the 2-Port PoE Gigabit Switch

• Connect the switch from the PD port to your central Gigabit PoE Switch.

• Connect your IP Phone from the PSE port on the switch.

• Connect your computer or other networking device to any of the PSE2 ports on the switch.

Link / Activity (green)

PSE-1 Power ON (yellow) PSE-2 Power ON (yellow) PD Power ON (yellow)

PoE Switch

Operations Guide 930591G CyberData Corporation

Appendix A: The Standard RJ-45 Introduction

Regarding cable-making methods, a cable which does not meet the standards of the sequence data

will make the data transmission speed slow, unstable and even be blocked.

Tabl e A-1 represents the

standard RJ-45 jack and the connector (Figure A-1) and pin definition:

Figure A-1. Standard RJ-45 Jack / Connector

Table A-1. RJ-45 Connector Pin Definitions

Pin Number Signal

1_TX1 +(PoE Power+)

2 _TX1 - (PoE Power+)

3 _RX1 + (PoE Power-)

4_TX2 +

5_TX2 --

6 _RX1 - (PoE Power-)

7_RX2 +

8_RX2 -

The Standard Cable, RJ-45 Pin Assignment

Operations Guide 930591G CyberData Corporation

A.1 The Standard Cable, RJ-45 Pin Assignment

The following figures shows a straight cable and a crossover cable connection. Use a straight cable

connection to connect switch/Hub or other devices:

Figure A-2. Straight cable for the switch (uplink MDI-II port) to switch/Hub or other devices

connection.

Figure A-3. Crossover cable for switch (MDI-X port) to switch/hub or other network devices

(MDI-X port) connection.

Operations Guide 930591G CyberData Corporation

Appendix B: Mounting

B.1 Dimensions and Mounting Hole Measurements

Figure B-1 shows the dimensions and mounting hole measurements for the 2-Port PoE Gigabit

Switch.

Figure B-1. Dimensions and Mounting Hole Measurements

4.832 [122.7]

DIMENSIONS ARE IN INCHES [MILLIMETER]

3.033 [77.0]

1.063 [27.0]

5.305 [134.7]

Ø0.217

[Ø5.5]

PSE PSE PD

CyberData Corporation

www.cyberdata.net

Mounting Option

Operations Guide 930591G CyberData Corporation

B.2 Mounting Option

Figure B-2 shows a mounting option for the 2-Port PoE Gigabit Switch.

Figure B-2. Mounting

Mounting Option:

1. Mounting Screw

• Use a size 6 to 8 pan head screw.

2. Adhesive

• Peel off the adhesive backing and

attach the unit to a suitable surface.

Operations Guide 930591G CyberData Corporation

Appendix C: Typical Installation

C.1 Example

Figure C-1 shows a typical installation setup for the 2-Port PoE Gigabit Switch.

Figure C-1. Typical Installation

CyberData 011187 Operations Guide

Brand: CyberData

Model: 011187

Category: Network switches

Type: Operations Guide

The switch also supports 10/100/1000Mbps data rates, making it suitable for use in high-speed networks.

Download PDF

report

CyberData 011187 Operations Guide

CyberData 011187 Operations Guide

Related papers

Other documents