Alfa Network AIP-W525H V2 Setup Manual

Brand: Alfa Network

Model: AIP-W525H V2

Type: Setup Manual

Presentd by

www.PcXpert.org

AIP-W525H_V2 Wifi Repeater, also called Wifi Extender setup

Before you start, read this entire document.

Configuration Alfa AIP-W525H in "Repeater" mode

This setup allows you to connect the AIP-W525H on an existing router, the connection

between the two Routers is wireless. In "Repeater" mode, DHCP is disabled, the main

router assigns all IP addresses to connected devices. All computers connected to both

routers can communicate with each other. The Repeater can use the same or can have

its own wifi name [SSID]. In "Repeater" mode the AIP-W525H can be placed anywhere,

as long as it can reach the wireless Network you want connect to.

Important:

Before you configure your AIP-W525H, you must know the wireless network name

[SSID] and password (security key) of your existing router.

1. Simplified setup: connect the AIP-W525H to a Power source, connect a network

cable to your computer and the other end to one of the routers LAN ports.

Open an internet page, type 192.168.2.1 and press « Enter »

This page should open

Click Operation Mode, check Repeater, click Apply, the Router will reboot.

After reboot click on Advanced Settings + Basic Settings and type the main router’s

wireless network name in the SSID field [here linksys], also check the “Enable Universal

Repeater Mode” box and press “Apply Changes”

Click on Reboot Later

Go to Advanced Setting + Site Survey, check the main routers SSID [here linksys], then

click Next.

PS. If the main router’s SSID is password protected, a window will open and ask you the

password.

Click Connect and wait

If you can see Connect Successfully, go to final step. If not begin from start

Final step: click « Reboot Now »

Your Device is now set in Repeater mode !

===============================================================

2. Advanced Setup (optional)

Option 1. If you want to access your Repeater later, change the LAN address.

To do this you must first know the address of the main router.

In this example the main router’s address is 192.168.1.1 and the Repeater’s address

192.168.1.2

PS. If you change the LAN address, you have to do that as first step and then

continue with simplified setup. To change LAN address, go to Advanced Settings + LAN

interface (see photos below)

Option 2. Use a different SSID for the repeater [here linksys2]

The difference is, main Router & Repeater will have their own SSID , linksys & linksys2

here, as shown below

Option 3, Password Protection (also called security key).

Important; if the repeater’s SSID is same as main router’s SSID, you have to set the

same password. If the main is not password protected, you have to leave the repeater’s

SSID unprotected too.

If you use a different SSID for the Repeater, you can do the setup with or without

password.

To set password; click Advanced Settings + Security Settings, in this example the

repeater SSID is W525H and Encryption is WPA2, just type the wanted password in Pré-

Shared Key Field and click Apply changes.

Important note:

This setup Guide is free to use or give away, but do not modify!

If you buy Alfa products from us, they come pre-configured for your needs

with 100% FREE support.

If you buy the product else were, we still can help you but charges are

applied.

If you don’t agree to pay for help, please do not ask us, contact your sales

person or find information on internet.

Peter Spani

www.PcXpert.org

1
2
3
4
5
6
7
8
9
10
11
12
13

Alfa Network AIP-W525H V2 Setup Manual

Brand: Alfa Network

Model: AIP-W525H V2

Type: Setup Manual

Download PDF

Related papers

Other documents