WAGO 3-Phase Power Measurement User manual

Pos: 2 /Dokumentation al lgemein/Einband/Ei nband Frontseite - Handbuch; CI 2017; mit DocVar iablen (Standard) @ 28\ mod_1486477502910_0. docx @ 405388 @ @ 1

Manual

WAGO I/O System 750 XTR

750-495/040-010

3

-Phase POM 20KV 300A XTR

3

-Phase Power Measurement; 20 kV AC; 300 A;

Extreme

(* only in connection with sensors according to section “Measurement of

Voltage, Current and Power”)

Version 1.0.0

Pos: 3 /Alle Serien (Al lgemeine Module)/Rec htliches, Allgemeines/ Impressum für Standar dhandbücher - allg. Angaben, Anschrif ten, Telefonnummern und E-Mai l-Adressen @ 3\mod_1219151118 203_21.docx @ 21060 @ @ 1

2 WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 4 45 55

Fax: +49 (0) 571/8 87 – 84 45 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

=== Ende der Liste für Textmarke Einband_vorne ===

WAGO I/O System 750 XTR Table of Contents 3

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 5 /Dokumentation al lgemein/Verzeic hnisse/Inhalts verzeichnis - Überschri ft oG und Verzeichnis @ 3\ mod_1219151230875_21. docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation .............................................................. 6

1.1 Validity of this Documentation .................................................................. 6

1.2 Revision History ....................................................................................... 7

1.3 Copyright.................................................................................................. 7

1.4 Symbols ................................................................................................... 8

1.5 Number Notation ...................................................................................... 9

1.6 Font Conventions ..................................................................................... 9

2 Important Notes ........................................................................................ 10

2.1 Legal Bases ........................................................................................... 10

2.1.1 Subject to Changes ........................................................................... 10

2.1.2 Personnel Qualifications.................................................................... 10

2.1.3 Use of the 750 Series in Compliance with Underlying Provisions ..... 10

2.1.4 Technical Condition of Specified Devices ......................................... 11

2.1.4.1 Disposal ........................................................................................ 11

2.1.4.1.1 Electrical and Electronic Equipment ........................................ 11

2.1.4.1.2 Packaging ................................................................................ 12

2.2 Safety Advice (Precautions) ................................................................... 13

3 Device Description ................................................................................... 16

3.1 View ....................................................................................................... 18

3.2 Connectors ............................................................................................. 19

3.2.1 Data Contacts/Local Bus ................................................................... 19

3.2.2 Power Jumper Contacts/Field Supply ............................................... 19

3.2.3 CAGE CLAMP

®

Connectors .............................................................. 20

3.3 Display Elements ................................................................................... 21

3.4 Operating Elements ............................................................................... 22

3.5 Schematic Diagram ................................................................................ 22

3.6 Technical Data ....................................................................................... 24

3.6.1 Device Data ....................................................................................... 24

3.6.2 Power Supply .................................................................................... 24

3.6.3 Measurement Inputs.......................................................................... 25

3.6.4 Measured Values .............................................................................. 26

3.6.5 Measurement Accuracy..................................................................... 28

3.6.6 Communication ................................................................................. 28

3.6.7 Connection Technology..................................................................... 28

3.6.8 Mechanical Conditions ...................................................................... 29

3.6.9 Climatic Environmental Conditions .................................................... 29

3.7 Approvals ............................................................................................... 30

3.8 Standards and Guidelines ...................................................................... 31

4 Function Description ................................................................................ 35

4.1 Measurement Principle .......................................................................... 35

4.2 Measured Value Overview ..................................................................... 35

4.3 Description of the Measured Values ...................................................... 37

4.4 Measurement Errors .............................................................................. 43

5 Process Image .......................................................................................... 46

4 Table of Contents WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

5.1 Overview of the Process Data ............................................................... 47

5.2 Output Data............................................................................................ 48

5.2.1 Definition of the Control Words ......................................................... 48

5.2.2 Definition of the Output Data Words .................................................. 49

5.3 Input Data .............................................................................................. 50

5.3.1 Definition of the Status Words ........................................................... 50

5.3.2 Definition of the Input Data Words .................................................... 55

5.4 Descriptions for the Process Image ....................................................... 59

5.4.1 AC Measured Value Collection (010) ................................................ 60

5.4.2 Harmonic Analysis Collections (020, 021, 022) ................................. 61

5.4.3 Transient Reaction Measured Values ............................................... 63

5.5 Measured Value Collections .................................................................. 64

5.5.1 Collection 010 – AC Measured Values .............................................. 64

5.5.2 Collections 020, 021 and 022 – Harmonic Analysis .......................... 68

5.6 Examples of the Calculation of the Measured Values from the

Process Values ...................................................................................... 69

6 Mounting ................................................................................................... 71

6.1 Mounting Sequence ............................................................................... 72

6.2 Inserting and Removing Devices ........................................................... 73

6.2.1 Inserting the I/O Module .................................................................... 73

6.2.2 Removing the I/O Module.................................................................. 74

7 Connect Devices ....................................................................................... 75

7.1 Protection against Hazardous Touch Voltages ...................................... 75

7.2 Shielding ................................................................................................ 76

7.2.1 General ............................................................................................. 76

7.2.2 Fieldbus Cables................................................................................. 76

7.2.3 Shielded Signal Lines ........................................................................ 77

7.3 Connecting a Conductor to the CAGE CLAMP

®

.................................... 78

7.4 Measurement of Voltage, Current and Power ........................................ 79

8 Commissioning ......................................................................................... 81

8.1 General .................................................................................................. 81

8.1.1 Software Interface ............................................................................. 82

8.1.2 “Start” Ribbon .................................................................................... 84

8.1.3 “Measured Value Views” Menu ......................................................... 84

8.1.4 Status Bar ......................................................................................... 85

8.1.5 “Settings” Dialog ................................................................................ 86

8.1.6 Setting Measurement Units ............................................................... 88

8.2 Settings and Measured Values .............................................................. 89

8.2.1 “I/O Module” Tab ............................................................................... 89

8.2.2 Tabs “Phase L1,” “Phase L2” and “Phase L3” ................................... 91

8.2.3 “Energy” Tab ..................................................................................... 92

8.2.4 “Factory Settings” Tab ....................................................................... 94

8.2.5 Displaying the Measured Values with WAGO-I/O-CHECK ............... 96

8.2.5.1 “Overview” View ........................................................................... 96

8.2.5.2 “Current/Voltages” View ............................................................... 98

8.2.5.3 “Powers” View .............................................................................. 99

8.2.5.4 “Energies” View .......................................................................... 100

8.2.5.5 “Upper Harmonics” View ............................................................ 101

WAGO I/O System 750 XTR Table of Contents 5

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

8.2.5.6 “Measurement Recording” View ................................................. 103

8.2.5.7 “Information” View ...................................................................... 104

9 Firmware Update .................................................................................... 105

10 Appendix ................................................................................................. 106

10.1 Examples of CSV Files ........................................................................ 106

10.1.1 Snapshot ......................................................................................... 106

10.1.2 Measurement Recording ................................................................. 111

10.2 Factory Settings ................................................................................... 112

10.3 Register Assignment ............................................................................ 114

10.4 Parameter Assignment ........................................................................ 121

List of Figures .................................................................................................. 126

List of Tables .................................................................................................... 127

=== Ende der Liste für Textmarke Verzeichnis_ vorne ===

6 Table of Contents WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 7 /Alle Serien (Al lgemeine Module)/Über schriften/Ebene 1/ Hinweise zu dieser Dokumen tation - Überschr ift 1 @ 4\mod_1237987661750_21.d ocx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /Alle Serien (Al lgemeine Module)/Si cherheits- und sonstige Hinweise/Hinweis/ Hinweis: Dokumentati on aufbewahren @ 4\mod_12379873 39812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation

is included, if necessary.

Pos: 9 /Alle Serien (Al lgemeine Module)/Über schriften/Ebene 2/ Gültigkeitsbereic h - Überschrift 2 @ 12\ mod_1338912448776_21.doc x @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /Serie 750 (W AGO I/O SYSTEM)/Hinweise zur Doku mentation (alte Struk tur)/Gültigkeits bereich/Gültig keitsbereich Dokumen tation I /O-Modul 750-xxxx, ohne Varian tenangabe @ 14\mod_13589 44037947_21.docx @ 1093 46 @ @ 1

This documentation is only applicable to the I/O module 750-495/040-010

(3-Phase POM 20KV 300A XTR).

Pos: 11 /Serie 750 (W AGO I/O SYSTEM)/Hinweise zur Doku mentation (alte Struk tur)/Hinweise/Ac htung: Hinweis zur Doku mentation I/O-Modul e 750-xxxx/040-000 @ 27\mod_14 68502299549_21.doc x @ 216892 @ @ 1

The I/O module 750-495/040-010 shall only be installed and operated according

to the instructions in this manual, in the system description for the WAGO I/O

System 750 XTR and in the manual for the used fieldbus coupler/controller.

Consider power layout of the WAGO I/O System 750 XTR!

In addition to these operating instructions, you will also need the system

description “Design Notes XTR – Guidelines and Recommendations for

Increasing Operational Safety” and the manual for the used fieldbus

coupler/controller, which can be downloaded at www.wago.com

. There, you can

obtain important information including information on electrical isolation, system

power and supply specifications.

Pos: 12 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

WAGO I/O System 750 XTR Table of Contents 7

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 13 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/Än derungshistori e - Überschrift 2 @ 6\mod_12555133 12687_21.docx @ 42790 @ 2 @ 1

1.2 Revision History

Pos: 14 /Serie 750 (W AGO I/O SYSTEM)/Hinweise zur Doku mentation (alte Struk tur)/Änderungshi storie/I/O-Module/ Änderungshistori e -495/040-010 @ 35\mod_1 561045680846_21.doc x @ 548579 @ @ 1

Table 1: Revision History

Document

Version

Device Version

Change

Hardware

Firmware

1.0.0

01 and

above

01

Initial publication

Pos: 15.1 /Alle Serien ( Allgemeine Module)/ Überschriften/E bene 2/Urheberschutz - Üb erschrift 2 @ 23\mod_1435647 042188_21.doc x @ 184808 @ 2 @ 1

1.3 Copyright

Pos: 15.2 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Urheberschut z ausführlich @ 4\mod_123 5565145234_21.doc x @ 27691 @ @ 1

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 15.3 /Dokumenta tion allgemein/Glied erungselemente/- --Seitenwechsel--- @ 3\mod_12211 08045078_0.doc x @ 21810 @ @ 1

8 Table of Contents WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 15.4 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Symbole - Überschr ift 2 @ 13\mod_1351068042408 _21.docx @ 105270 @ 2 @ 1

1.4 Symbols

Pos: 15.5.1 /Alle Serien ( Allgemeine Module) /Sicherheits- und son stige Hinweise/Gef ahr/Gefahr: _War nung vor Personenschäden allg emein_ - Erläuterung @ 13\ mod_1343309450020_2 1.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 15.5.2 /Alle Serien ( Allgemeine Module) /Sicherheits- und son stige Hinweise/Gef ahr/Gefahr: _War nung vor Personenschäden durc h elektrischen Stro m_ - Erläuterung @ 13\mod_13433 09694914_21.doc x @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 15.5.3 /Alle Serien ( Allgemeine Module) /Sicherheits- und son stige Hinweise/W arnung/Warnung: _War nung vor Personenschäden all gemein_ - Erläuterung @ 13\mo d_1343309877041_21.doc x @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 15.5.4 /Alle Serien ( Allgemeine Module) /Sicherheits- und son stige Hinweise/Vor sicht/Vorsicht: _Warnung vor Personenschäden a llgemein_ - Erläuter ung @ 13\mod_13433100287 62_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 15.5.5 /Alle Serien ( Allgemeine Module) /Sicherheits- und son stige Hinweise/Ac htung/Achtung: _War nung vor Sachschäden allge mein_ - Erläuterung @ 13\mod_ 1343310134623_21. docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 15.5.6 /Alle Serien ( Allgemeine Module) /Sicherheits- und son stige Hinweise/Ac htung/Achtung: _War nung vor Sachschäden durc h elektrostatische Auf ladung_ - Erläuterung @ 13\ mod_1343310227702_ 21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 15.5.7 /Alle Serien ( Allgemeine Module) /Sicherheits- und son stige Hinweise/Hin weis/Hinweis: _W ichtiger Hinweis allgemei n_ - Erläuterung @ 13\mod_134 3310326906_21.doc x @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 15.5.8 /Alle Serien ( Allgemeine Module) /Sicherheits- und son stige Hinweise/Inf ormation/Infor mation: _Weitere I nformation allgemein_ - Erläuterung @ 13\mod_13433 10439814_21.docx @ 101051 @ @ 1

WAGO I/O System 750 XTR Table of Contents 9

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 15.6 /Dokumenta tion allgemein/Glied erungselemente/ ---Seitenwechsel--- @ 3\mod_12211 08045078_0.doc x @ 21810 @ @ 1

Pos: 15.7 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Darstellung der Zahlensysteme - Überschr ift 2 @ 23\mod_1435647128078_2 1.docx @ 184811 @ 2 @ 1

1.5 Number Notation

Pos: 15.8 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Zahlensyste me @ 3\mod_1221059454015_21. docx @ 21711 @ @ 1

Table 2: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated

with dots (.)

Pos: 15.9 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Schriftkonventio nen - Überschri ft 2 @ 23\mod_1435647186005_21. docx @ 184814 @ 2 @ 1

1.6 Font Conventions

Pos: 15.10 /Alle Seri en (Allgemeine Module)/ Rechtliches, Allge meines/Schrif tkonventionen @ 3\mod_1221059 521437_21.doc x @ 21714 @ @ 1

Table 3: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu

Menu items are marked in bold letters.

e.g.: Save

>

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.:

Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.:

[F5]

Pos: 16 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

10 Table of Contents WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 17 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 1/W ichtige Erläuterun gen - Überschrif t 1 @ 4\mod_1241428899156_21.doc x @ 32170 @ 1 @ 1

2 Important Notes

Pos: 18.1 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Wichtige Er läuterungen - Einleitung @ 3\m od_1221059818031_2 1.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 18.2 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/ Rechtliche Grundl agen - Überschrif t 2 @ 3\mod_1221060626343_21.d ocx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 18.3 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Änderungsvorbe halt - Überschri ft 3 und Inhalt @ 3\mod_122106003 6484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all

rights arising from the granting of patents or from the legal protection of utility

patents. Third-party products are always mentioned without any reference to

patent rights. Thus, the existence of such rights cannot be excluded.

Pos: 18.4 /Serie 750 (W AGO I/O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Personalqua lifikation/Pers onalqualifikati on 750-xxxx - Überschr ift 3 und Inhalt - ohne "Automa tisierung..." @ 37\ mod_1600684975969_21.doc x @ 594039 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO I/O System 750 devices may only be

carried out by electrical specialists with sufficient knowledge. The specialists

must be familiar with the current norms and guidelines for the devices and

environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 18.5 /Serie 750 (W AGO I/O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Bestimmung sgemäße Verwendung/Bes timmungsgemäße Verwendun g 750-xxxx - Überschr ift 3 @ 32\mod_15360411415 28_21.docx @ 498494 @ 3 @ 1

2.1.3 Use of the 750 Series in Compliance with Underlying

Provisions

Pos: 18.6 /Serie 750 (W AGO I/O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Bestimmung sgemäße Verwendung/Bes timmungsgemäße Verwendun g 750-xxxx für Geräte, STD mit EN 61000-6-3 -Verweis auf Ger äte-HB @ 3\mod_12 24064151234_21.doc x @ 24070 @ @ 1

Fieldbus couplers, controllers and I/O modules found in the modular WAGO I/O

System 750 receive digital and analog signals from sensors and transmit them to

actuators or higher-level control systems. Using controllers, the signals can also

be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO I/O System 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information in

the section “Device Description” > “Standards and Guidelines” in the manual for

the used device.

WAGO I/O System 750 XTR Table of Contents 11

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Appropriate housing (per 2014/34/EU) is required when operating the WAGO I/O

System 750 in hazardous environments. Please observe the installation

regulations! Please note that a prototype test certificate must be obtained that

confirms the correct installation of the system in a housing or switch cabinet.

The implementation of safety functions such as EMERGENCY STOP or safety

door monitoring must only be performed by the F I/O modules within the modular

WAGO I/O System 750. Only these safe F I/O modules ensure functional safety

in accordance with the latest international standards. WAGO's interference-free

output modules can be controlled by the safety function.

Pos: 18.7 /Alle Serien ( Allgemeine Module)/ Rechtliches, Allge meines/Technischer Zustand der Geräte - Übersc hrift 3 und Inhalt @ 3\mod_12210 60446109_21.doc x @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. These

modules contain no parts that can be serviced or repaired by the user. The

following actions will result in the exclusion of liability on the part of WAGO

Kontakttechnik GmbH & Co. KG:

• Repairs,

• Changes to the hardware or software that are not described in the

operating instructions,

• Improper use of the components.

Further details are given in the contractual agreements. Please send your

request for modified and new hardware or software configurations directly to

WAGO Kontakttechnik GmbH & Co. KG.

Pos: 18.8 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 4/ Entsorgen - Überschr ift 4 @ 30\mod_151014511565 2_21.docx @ 469859 @ 4 @ 1

2.1.4.1 Disposal

Pos: 18.9.1 /Alle Serien ( Allgemeine Module) /Überschriften/ Ebene 5/Elektro- und Ele ktronikgeräte - Übersc hrift 5 @ 32\mod_153744698 8068_21.docx @ 501657 @ 5 @ 1

2.1.4.1.1 Electrical and Electronic Equipment

Pos: 18.9.2 /Alle Serien ( Allgemeine Module) /Rechtliches, Allg emeines/Elektro- und E lektronikgeräte @ 32\m od_1532425086061_21. docx @ 491989 @ @ 1

Electrical and electronic equipment may not be disposed of

with household waste. This also applies to products without

this symbol.

Electrical and electronic equipment contain materials and substances that can be

harmful to the environment and health. Electrical and electronic equipment must

be disposed of properly after use.

WEEE 2012/19/EU applies throughout Europe. Directives and laws may vary

nationally.

12 Table of Contents WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Environmentally friendly disposal benefits health and protects

the environment from harmful substances in electrical and

electronic equipment.

• Observe national and local regulations for the disposal of electrical and

electronic equipment.

• Clear any data stored on the electrical and electronic equipment.

• Remove any added battery or memory card in the electrical and

electronic equipment.

• Have the electrical and electronic equipment sent to your local

collection point.

Improper disposal of electrical and electronic equipment can be harmful to the

environment and human health.

Pos: 18.9.3 /Dokumen tation allgemein/Gli ederungselemente/ ----Leerzeile-(1Z) ---- @ 28\mod_1485262995837_0. docx @ 404006 @ @ 1

Pos: 18.9.4 /Alle Serien ( Allgemeine Module) /Überschriften/ Ebene 5/Verpackung - Übersc hrift 5 @ 32\mod_153744704 4202_21.docx @ 501662 @ 5 @ 1

2.1.4.1.2 Packaging

Pos: 18.9.5 /Alle Serien ( Allgemeine Module) /Rechtliches, Allg emeines/Verpackung @ 32\ mod_1537446786416_21. docx @ 501653 @ @ 1

Packaging contains materials that can be reused.

PPWD 94/62/EU and 2004/12/EU packaging guidelines apply throughout

Europe. Directives and laws may vary nationally.

Environmentally friendly disposal of the packaging protects the environment and

allows sustainable and efficient use of resources.

• Observe national and local regulations for the disposal of packaging.

• Dispose of packaging of all types that allows a high level of recovery,

reuse and recycling.

Improper disposal of packaging can be harmful to the environment and wastes

valuable resources.

Pos: 18.10 /Dokumenta tion allgemein/Glie derungselemente/---Sei tenwechsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

WAGO I/O System 750 XTR Table of Contents 13

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 18.11 /Alle Seri en (Allgemeine Module)/ Überschriften/Eben e 2/Sicherheitshi nweise - Überschri ft 2 @ 6\mod_1260180299987_21. docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 18.12 /Alle Seri en (Allgemeine Module)/ Sicherheits- und sons tige Hinweise/Einlei tung Sicherheitshi nweise Hardware @ 6\mod_1260 180170493_21.doc x @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 18.13 /Serie 750 (W AGO I/O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Sicher heits- und sonstige Hin weise/Gefahr/Gefahr: Installation und W artung nur durch geschultes Fac hpersonal @ 35\mod_156 1660289052_21.doc x @ 549373 @ @ 1

Installation and maintenance only by trained specialist personnel

The I/O module must only be installed and maintained by trained specialist

personnel in the medium voltage range.

Pos: 18.14 /Serie 750 (W AGO I/O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Sicher heits- und sonstige Hin weise/Gefahr/Gefahr: Ausschließlich nor mgerechte Sensoren einse tzen und technische Daten b eachten @ 35\mod_156166 0040009_21.doc x @ 549369 @ @ 1

Use only standards-compliant sensors, and pay attention to the technical

data

Use only voltage sensors approved per IEC 60044-7 (new version: IEC 61869-7)

and current sensors per IEC 60044-8 (new version: IEC 61869-8), and do so in

accordance with the information in the section “Technical Data.”

Pos: 18.15 /Serie 750 (W AGO I/O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Sicher heits- und sonstige Hin weise/Gefahr/Gefahr: Berührungsschutz vor sehen! -für Messaufbau @ 15\m od_1366120208015_2 1.docx @ 117160 @ @ 1

Install protection against electric shock!

All wiring for the measurement system shall be provided with protection against

shock hazard voltages along with the corresponding safety signs!

Pos: 18.16.1 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/ Gefahr/Gefahr: Nic ht an Geräten unter Spannung ar beiten! @ 6\mod_126018036 5327_21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 18.16.2 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/ Gefahr/Gefahr: Pr odukt nur in einem geeigneten Gehäu se einbauen! @ 33\mod_154 3581881435_21.doc x @ 511972 @ @ 1

Install device in only one suitable enclosure!

The device is an open system. Install the device in a suitable enclosure. This

enclosure must:

• Guarantee that the max. permissible degree of pollution is not exceeded.

• Offer adequate protection against contact.

• Prevent fire from spreading outside of the enclosure.

• Offer adequate protection against UV irradiation.

• Guarantee mechanical stability

• Restrict access to authorized personnel and may only be opened with tools

Pos: 18.16.3 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/ Gefahr/Gefahr: Trenn vorrichtung und Überstro mschutz @ 33\mod_1543915 978439_21.doc x @ 512267 @ @ 1

14 Table of Contents WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Ensure disconnect and overcurrent protection!

The device is intended for installation in automation technology systems.

Disconnect protection is not integrated. Connected systems must be protected by

a fuse.

Provide suitable disconnect and overcurrent protection on the system side!

Pos: 18.16.4 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/ Gefahr/Gefahr: Unfall verhütungsvorschr iften beachten! @ 6\mod_1 260180657000_21.doc x @ 46735 @ @ 1

Pos: 18.16.5 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/ Gefahr/Gefahr: Auf normgerechten Anschluss ac hten! @ 6\mod_126018075347 9_21.docx @ 46739 @ @ 1

Ensure a standard connection!

To minimize any hazardous situations resulting in personal injury or to avoid

failures in your system, the data and power supply lines shall be installed

according to standards, with careful attention given to ensuring the correct

terminal assignment. Always adhere to the EMC directives applicable to your

application.

Pos: 18.17 /Alle Seri en (Allgemeine Module)/ Sicherheits- und sons tige Hinweise/Gefahr /Gefahr: Leitungen nur in spannungsfreiem Zus tand anschliessen oder trennen - Sensoren auf Pr imäreite @ 35\mod_156750445 6177_21.docx @ 558298 @ @ 1

Only connect or disconnect lines when power is safely isolated

Hazardous voltages and currents are present on the primary side of the sensors

used. Contact with the lines when they are live can result in severe injury or

death. Therefore, read and observe the following safety rules before you perform

work on the device:

1. Disconnect the respective system component from the power supply.

2. Secure the system component against unintentional restart.

3. Verify that the voltage is actually isolated.

Pos: 18.18 /Alle Seri en (Allgemeine Module)/ Sicherheits- und sons tige Hinweise/Vorsi cht/Vorsicht: Heiße Oberfläche nicht berühr en! (allgemein) @ 6\ mod_1264428115588_21. docx @ 48610 @ @ 1

Do not touch hot surfaces!

The surface of the housing can become hot during operation. If the device was

operated at high ambient temperatures, allow it to cool off before touching it.

Pos: 18.19.1 /Seri e 750 (WAGO I/O SYSTEM)/Wic htige Erläuterungen (alt e Struktur)/Sic herheits- und sonstige Hin weise/Achtung/Ac htung: Einwandfreie Kon taktierung zur Tragsc hiene gewährleiste n! @ 34\mod_1550481407638_2 1.docx @ 530599 @ @ 1

Ensure proper contact with the DIN-rail!

Proper electrical contact between the DIN-rail and device is necessary to

maintain the EMC characteristics and function of the device.

Pos: 18.19.2 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/Ac htung/Achtung: Defek te oder beschädigte Ger äte austauschen! @ 6\ mod_1260180857358_21.d ocx @ 46743 @ @ 1

WAGO I/O System 750 XTR Table of Contents 15

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts).

Pos: 18.19.3 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/Ac htung/Achtung: Gerät e vor kriechenden und isoli erenden Stoffen schü tzen! @ 6\mod_1260181036216 _21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for

handling devices/modules.

Pos: 18.19.4 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/Ac htung/Achtung: Reini gung nur mit zulässigen M aterialien! @ 6\mod_1260 181203293_21.doc x @ 46751 @ @ 1

Clean only with permitted materials!

Clean housing and soiled contacts with propanol.

Pos: 18.19.5 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/Ac htung/Achtung: Kein Kon taktspray verwenden! @ 6\mod_1260181290808_ 21.docx @ 46755 @ @ 1

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 18.19.6 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/Ac htung/Achtung: Verpo lungen der Daten- und Versor gungsleitungen vermeiden! @ 6\mod_1260184045 744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 18.19.7 /Alle Ser ien (Allgemeine Module) /Sicherheits- und son stige Hinweise/Ac htung/Achtung: Elek trostatische Entlad ung vermeiden! - DI N EN 613 40-5-1/-3 @ 6\mod_12601 81364729_21.docx @ 4675 9 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 19 /Dokumentation al lgemein/Glieder ungselemente/---Sei tenwechsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

16 Table of Contents WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 20 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 1/ Gerätebeschreibung - Überschrift 1 @ 3\mod_12337 56084656_21.doc x @ 27096 @ 1 @ 1

3 Device Description

Pos: 21 /Serie 750 (W AGO I/O SYSTEM)/Gerätebeschr eibung (alte Struktur )/Einleitung/AI /Gerätebeschrei bung - Einleitung 750-0495/ 040-010 @ 35\mod_156104582 5772_21.docx @ 548583 @ @ 1

The 750-495/040-010 3-Phase Power Measurement Module (also referred to by

the short name “I/O module”) allows measurement of electrical data in a 3-phase

supply network in the medium voltage range up to 20 kV

RMS

by means of voltage

sensors per IEC 60044-7 (new version: IEC 61869-7) and current sensors per

IEC 60044-8 (new version: IEC 61869-8). Observe the information in chapter

“Technical Data”.

The I/O module measures nominal voltages up to U

LL

= 20 kV

RMS

(U

LN

=

11.547 kV

RMS

) and line-to-line nominal currents up to 300 A

RMS

. It provides a large

number of measured variables, allowing comprehensive analysis of the 3-phase

network. These measured values allow operators optimized control of their

equipment, protecting the system against damage and failure.

The measured values provided by the I/O module indicate the load type

(inductive or capacitive) and whether it is an energy consumer or producer, for

example. This allows visualization as a 4-quadrant display, as has been

implemented in the display of the measured values in WAGO-I/O-CHECK,

among other things.

The measured values provided are described in the following sections.

The voltages of the 3 phases are connected via voltage sensors to CAGE

CLAMP® connections L1, L2, L3 and N, and the currents are connected via

current sensors to CAGE CLAMP® connections I1, I2, I3 and N. On the basis of

these input signals, the I/O module determines the various AC measured

quantities, such as voltage and current, reactive, apparent and active power,

energy consumption, power factor, phase angle and frequency. Harmonic

analysis (current/voltage) is also possible for a selectable phase up to the

41st harmonic. The measured quantities are available in the process image,

without requiring high processing power from the controller.

Use only standards-compliant sensors, and pay attention to the technical

data

Use only voltage sensors approved per IEC 60044-7 (new version: IEC 61869-7)

and current sensors per IEC 60044-8 (new version: IEC 61869-8), and do so in

accordance with the information in the section “Technical Data.”

I/O module not suitable for billing purposes

Regardless of the accuracy class of the current and voltage sensors used, the

I/O module is not approved as a meter for billing purposes in the sense of the

electricity metering standard (DIN 43856).

Pos: 22 /Serie 750 (W AGO I/O SYSTEM)/Wichtige Er läuterungen (alte Struk tur)/Sicherhei ts- und sonstige Hinweise/ Hinweis/Hinweis: Pot entialeinspei semodul einsetzen! (kei ne LK) @ 3\mod_12264990896 40_21.docx @ 25026 @ @ 1

WAGO I/O System 750 XTR Table of Contents 17

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Use a power supply module!

Use a power supply module for field-side power supply of downstream I/O

modules.

Pos: 23 /Serie 750 (W AGO I/O SYSTEM)/Wichtige Er läuterungen (alte Struk tur)/Sicherhei ts- und sonstige Hinweise/ Hinweis/Hinweis: X TR - Mischbetrieb XTR/S tandard @ 15\mod_1367496420 828_21.docx @ 118326 @ @ 1

Mixed operation

Mixed operation (standard/XTR modules) within a node is possible when groups

of modules are electrically isolated on the field side (i.e., electrically isolated

power supply).

Pos: 24 /Serie 750 (W AGO I/O SYSTEM)/Gerätebeschr eibung (alte Struktur )/Einleitung/Ei nsatzbereich/ Einsatzbereich 750-xxxx/ 040-000 alle XTR-Koppler/ Controller ohne Ein schränkung+Mischbe triebhinweis @ 32\mod_1 532012421157_21.doc x @ 491879 @ @ 1

The I/O module can be operated with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750 XTR.

Observe the instruction for mixed operation when used in mixed operation behind

standard fieldbus couplers/controllers.

Pos: 25 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

18 Table of Contents WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 26 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/An sicht - Überschri ft 2 @ 4\mod_1240984217343_21. docx @ 31958 @ 2 @ 1

3.1 View

Pos: 27 /Serie 750 (W AGO I/O SYSTEM)/Gerätebeschr eibung (alte Strukt ur)/Ansicht/AI /Ansicht 750-0495/040-01 0 @ 35\mod_1561045940091_21. docx @ 548587 @ @ 1

Figure 1: View 750-495/040-010

Pos: 28 /Serie 750 (W AGO I/O SYSTEM)/Gerätebeschr eibung (alte Struktur )/Ansicht/Ansic ht CageClamp®_Legende mit LED s_ohne Leistungsk ontakte @ 16\mod_13718160 91053_21.docx @ 124052 @ @ 1

Table 4: Legend for Figure “View”

Pos.

Description

Details See Section

1

Marking possibility with Mini-

WSB

---

2

Status LEDs

“Device Description” > “Display Elements”

3

Data contacts

“Device Description” > “Connectors”

4

CAGE CLAMP

®

connectors

“Device Description” > “Connectors”

5

Release tab

“Mounting” > ”Inserting and Removing

Devices”

Pos: 29 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804507 8_0.docx @ 21810 @ @ 1

WAGO I/O System 750 XTR Table of Contents 19

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 30 /Alle Serien ( Allgemeine Module)/ Überschriften/Ebene 2/An schlüsse - Übersc hrift 2 @ 4\mod_1240984262656_2 1.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 31 /Serie 750 (W AGO I/O SYSTEM)/Gerätebeschr eibung (alte Struktur )/Anschlüsse/Dat enkontakte/Lokal bus - Überschri ft 3 @ 6\mod_1256294684083_21. docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Local Bus

Pos: 32.1 /Serie 750 (W AGO I/O SYSTEM)/Gerätebesc hreibung (alte Strukt ur)/Anschlüsse/ Datenkontakte - Feldbusko ppler/-contr oller und Module – Abbildu ng und Beschreibung @ 3\mod_12 31771259187_21.doc x @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the local bus. The

contacting for the local bus consists of 6 data contacts, which are available as

self-cleaning gold spring contacts.

Figure 2: Data Contacts

Pos: 32.2 /Serie 750 (W AGO I/O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Sicher heits- und sonstige Hinweise/ Achtung/Achtun g: I/O-Module nicht auf Goldf ederkontakte legen! @ 7\mod_1266318463636_2 1.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 32.3 /Serie 750 (W AGO I/O SYSTEM)/Wichti ge Erläuterungen (alte Str uktur)/Sicher heits- und sonstige Hinweise/ Achtung/Achtun g: ESD - Auf Potentialausgl eich der Umgebung achten! @ 32\ mod_1539077262331_21. docx @ 504433 @ @ 1

Pay attention to potential equalization from the environment!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, please ensure that

environmental factors (personnel, work space and packaging) are properly

equalized. Do not touch any conducting parts, e.g., data contacts.

Pos: 33 /Serie 750 (W AGO I/O SYSTEM)/Gerätebeschr eibung (alte Struktur )/Anschlüsse/Leis tungskontakte/Fel dversorgung - Übersc hrift 3 @ 6\mod_125629469286 4_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 34 /Serie 750 (W AGO I/O SYSTEM)/Gerätebeschr eibung (alte Struktur )/Anschlüsse/Leis tungskontakte nic ht vorhanden @ 8\mod_1281073 936319_21.doc x @ 62530 @ @ 1

The I/O module 750-495/040-010 has no power jumper contacts.

Pos: 35 /Serie 750 (W AGO I/O SYSTEM)/Wichtige Er läuterungen (alte Struk tur)/Sicherhei ts- und sonstige Hinweise/ Hinweis/Hinweis: Pot entialeinspei semodul einsetzen! (kei ne LK) @ 3\mod_12264990896 40_21.docx @ 25026 @ @ 1

Use a power supply module!

Use a power supply module for field-side power supply of downstream I/O

modules.

Pos: 36 /Dokumentation al lgemein/Glieder ungselemente/---Seitenwec hsel--- @ 3\mod_122110804 5078_0.docx @ 21810 @ @ 1

20 Table of Contents WAGO I/O System 750 XTR

750-495/040-010 3-Phase POM 20KV 300A XTR

Manual

Version 1.0.0

Pos: 37 /Serie 750 (W AGO I/O SYSTEM)/Gerätebeschr eibung (alte Struktur )/Anschlüsse/CAGE C LAMP-Anschlüsse - Über schrift 3 @ 6\mod_1256296337 770_21.docx @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP

®

Connectors

Pos: 38 /Serie 750 (W AGO I/O SYSTEM)/Gerätebeschr eibung (alte Struktur )/Anschlüsse/AI /Anschlüsse 750-0495/040- 010 CAGE CLAMP @ 35\mod_15610 46063456_21.doc x @ 548591 @ @ 1

Twelve CAGE CLAMP

®

connections allow the three voltage sensors and three

current sensors to be connected, each with a two-wire connection; see also

section “Connecting Devices.”

All N connections are connected internally to each other and are used for the

reference potential N. Therefore, all sensors use the same reference potential.

Figure 3: CAGE CLAMP

®

Connections of 750-495/040-010

Table 5: Legend for Figure “CAGE CLAMP

®