Digital Watchdog Spot DW-HDSPOTMOD16 User manual

Before operating the system, please read this user manual and retain it for future

reference.

The picture might differ according to the specification and model.

Rev: 07/20

USER MANUAL

DW Spot™ Monitoring Module

[2]

WARNING

TO REDUCE FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE.

The installation should be made by a qualified service

person and conformed to all local codes.

[3]

Cautions

Read Before System Operation

Follow these details to prevent material damage or personal injury.

Signs of Caution and Warning

Warning: This sign indicates that the user could die or be seriously wounded if not

used or installed properly.

Caution: This sign indicates that the user could be wounded or could expect property damage if not used or installed

properly.

Warning: Do not expose the product to fog, rain, or too much humid to decrease the danger from electric shock or fire

.

General Warning

Warning

1. Use the power cord, which is supplied or recommended by the supplier, or it may cause a fire.

2. Do not disassemble or reassemble the product. It may cause malfunction or fire.

3. Enquire to your vendor for repair. It may cause electric shock or fire if the repair is not done properly.

4. Do not touch the product with wet hands. It may cause malfunction or electric shock.

5. Product installation must be ensured to a professional for product installation, or it may cause malfunction, electric shock, or fire.

6. Ground applies to video products equipped with a 3-wire grounding type plug having a third (grounding) pin. This plug only fits

into a grounding-type power outlet. If grounding is not done, it may cause malfunction or electric shock.

7. A ground connection must not touch the gas pipe, water pipe, or telephone line. If grounding is not done properly, it may cause

electric shock.

8. Prevent metallic foreign substances from going inside the product. It may cause malfunction or electric shock.

9. Do not spray insecticide or flammable spray while driving. It may cause a fire.

10. Place the system in an open place where air ventilation is guaranteed, or it may cause over-heating and seriously damage the system

to be fired.

11. Prevent water from instilling inside electrical parts. Clean with a dry towel or malfunction or electric shock could result.

Caution

1. Use the power cord, which is supplied or recommended by the supplier. The internal fan rotates at high speed and may cause an

accident.

2. Do not drop, give strong vibration or shock to the product. It may cause malfunction.

3. The air inhaler of the front panel and air outlet of the back panel must not be blocked during installation.

The internal temperature of the product would be greater than allowable and could cause malfunction or fire.

4. Do not touch the product or the power cord when there is thunder. It may cause an electric shock.

5. Do not install the product near or on top of the heating source. The internal temperature of the product would be greater than

allowable and could cause malfunction or fire.

6. Do not install the product on an inclined or unstable location or where vibration could be committed. It may cause malfunction.

Cautions about the Power

Warning

1. Must use the outlet of the grounding to connect the power cord, or it may cause a fire.

2. Do not connect in the middle of the power cord or use the extension cord. It may generate heat or cause a fire.

3. Do not touch the power cord with wet hands. It may cause an electric shock.

4. Keep the power cord dry and protect from humidity. It may generate heat or cause a fire. The power cord is not waterproof.

5. Hold the body of the plug while removing the power plug. Do not pull the power cord. Damage to the power cord may generate

heat or cause a fire.

6. Check the power plug regularly. Humidity and moderation in smoking may cause a fire.

7. Remove the power cord from the outlet when the product is not used for a long time. It may cause short-circuit or electric shock.

Caution

1. Do not turn off the power by removal of the power plug.

To turn off the power, click the power button from the front panel.

When the system stops abnormally, the power button might not work. Click the power button for 5 full seconds to turn the power off.

2. Do not cut off the power artificially, or give shock or vibration to the unit while the hard disk is activating. It may cause hard disk

failure or loss of data.

Remarks

※ Pictures and buttons are subject to be changed or modified up to different models.

※ Function or configuration is subject to be changed or modified without prior notice for improvement of the product.

User Manual

[4]

Ta b l e o f Contents

1.

GETTING STARTED ................................................................................................................................. 5

1.1 Checking Supplied Items .................................................................................................................................... 5

1.2 System Startup ....................................................................................................................................................... 6

1.3 System Shutdown ................................................................................................................................................. 6

1.4 System Overview ................................................................................................................................................... 7

2.

STARTUP WIZARD .................................................................................................................................. 9

2.1 Language ................................................................................................................................................................. 9

2.2 Network .................................................................................................................................................................... 9

2.3 Camera Management .......................................................................................................................................... 11

2.4 Finish........................................................................................................................................................................ 12

3.

OPERATION .............................................................................................................................................. 12

3.1 User Log-in ............................................................................................................................................................ 12

3.2 DVR/NVR/CAM Registration ........................................................................................................................... 13

3.3 Deleting Devices .................................................................................................................................................. 15

3.4 Live Display Mode ............................................................................................................................................... 15

4.

SETTING .................................................................................................................................................... 19

4.1 System .................................................................................................................................................................... 20

4.2 Monitoring ............................................................................................................................................................. 26

4.3 Network ..................................................................................................................................................................27

5.

WEB SURVEILLANCE THROUGH INTERNET EXPLORER ............................................................ 31

5.1 Web Login.............................................................................................................................................................. 31

5.2 Web Setup ............................................................................................................................................................ 32

6.

Q & A ......................................................................................................................................................... 34

7.

PRODUCT SPECIFICATIONS ............................................................................................................... 35

8.

WARRANTY INFORMATION ................................................................................................................ 36

9.

LIMITS AND EXCLUSIONS ................................................................................................................... 37

Spot™ Monitoring Module

[5]

1.

Getting Started

1.1

Checking Supplied Items

Make sure that you have the following items supplied with your module. If any of these items are missing

or damaged, notify your vendor immediately. Keep the packing utilities for moving or storage purposes.

Items

Photo

Quantity

Quick setup and

download guides

1 set

12V D/C power cable

1 set

USB mouse

1

User Manual

[6]

1.2

System Startup

After connecting peripheral devices such as monitors and a mouse to the module, power up the

module by connecting DC12V adaptor/ power cable to the power jack on the rear panel. The boot

logo will display. Please wait until the boot process completes.

When the system is up, the password change window is displayed. The user must set the password to

a minimum of 8 characters with at least 3 combinations of uppercase letters, lower case letters, numbers

and special characters. Acceptable special characters are 『~ ‘ ! $ ^ ( ) _ - | { } [ ] ; . ? /』. To login, right-

click anywhere on the screen and enter the username and password in the popup screen. There is only

one Administrator Account configurable in the module. It is assigned with an unchangeable User ID

marked as ‘admin’. The administrator account has full access to the module and its configurable

parameters and can also create new users and assign rights to the new user accounts.

If the module is set as AUTO LOGIN, the login process is not necessary.

Caution

1) It may take a few minutes to start up the system after turning on the power, in case the

user sets the network configuration as DHCP mode but under the situation that there is

no DHCP server in the network or the network is not connected.

2) The mouse is included. In case you need to replace it, it is highly recommended to

choose well-known major brands such as DELL, MICROSOFT, LOGITECH, or

SAMSUNG.

Note

1) Contact DW’s technical support to reset your password.

2) Refer to “Section 4.1.2 User” for AUTO LOGIN and AUTO LOGOFF.

1.3

System Shutdown

To turn off the power, click the exit button [ ] the toolbar, then select SHUTDOWN in the Exit

screen.

Input the password and click the OK button to shut down the system. Click the YES button to confirm

shutdown.

Note

Input passwords using the virtual keyboard.

Spot™ Monitoring Module

[7]

1.4

System Overview

Front Panel

1. USB Port: for USB mouse, import, and export settings and firmware upgrade.

2. LED Indicator: Indicates system status. (Power, Record and Network status)

Back Panel

1. VGA out: connect a VGA monitor to the unit (cables not included).

2. HD out: Connect a true HD monitor to the unit (cables not included).

3. LAN: Connect an RJ45 cable to the unit to connect it to the local network (cables not

included).

4. Power: Connect the 12V DC power cable to the unit and then to an adequate power supply.

User Manual

[8]

Tool Bar

In live view, move the mouse cursor to the bottom of the screen to show the menu bar.

Menu

Click on the menu button to access the module’s main menu screen. See “4. Setting” for details.

Display Mode

Select the display split mode from the available options. Select 1CH, 4CH, 9CH or 16CH mode.

Sequence

Start/stop the sequence mode in live mode. The sequence is disabled if all channels are displayed.

Channel

Switch to a single-channel view of a specific channel by pressing the corresponding number.

Exit

Exit the module with three different options: Log Off, Reboot and Shutdown.

When selected, the menu bar will be fixed on the screen permanently, regardless of the mouse’s

position.

Spot™ Monitoring Module

[9]

2.

Startup Wizard

When the module is launched for the first time, the STARTUP WIZARD will appear. This wizard helps

you setup the module’s most basic settings for proper functioning. You can access the Startup Wizard

screen at any time by clicking the Startup Wizard button under the MENU>SYSTEM>SETTINGS menu.

(See “4.1.5 SETTINGS”). If “DISPLAY ON SYSTEM STARTUP” is selected, Startup Wizard will appear

every time the system reboots.

2.1

Language

Select the language from the available drop-down options. Click APPLY to save the changes and

NEXT to move to the next screen.

.

2.2

Network

Setup the module’s network settings for remote connection.

Network Type

DHCP: The module will acquire all the network settings automatically according to the current

network requirements. Click the ‘IP DETECT’ button to automatically fill out all the network settings.

Static IP: manually enter all the network settings. For proper configuration, it is recommended to

assign the module a DHCP address and let it auto-discover all the proper network settings, and

then change the Network Type back to Static IP and save the changes. Contact your Network

User Manual

[10]

Administrator for more information.

IP Address

If DHCP is selected, the IP address will automatically adjust to match the network’s requirements.

You may manually change the IP address as needed (Network Type must be set to Static).

Subnet Mask

Subnet Mask address classifies the subnet that the system belongs to. Contact your Network

Administrator for more information.

Gateway

This is the IP address of the router or gateway server. It is required when connecting to the module

through the external router over the internet (from another network). Contact your Network

Administrator for more information.

DNS Server

Enter the IP address of the Domain Name Server. You should input the DNS Server information to

use DDNS, E-mail notifications and NTP Server. Contact your Network Administrator for more

information.

WEB Port

Input the port number to use when connecting from the Web Browser. The default is 80. Contact

your Network Administrator for more information.

Auto IP

Displays the system’s IP address.

Use UPnP (Universal Plug and Play)

UPnP is a plug-and-play feature that allows the module to be automatically discovered by a PC on

the same network. To locate the module, go to “My Network” on your PC. The computer will scan

your network for all supported devices. The first five characters of the file name of a detected

module represent the model number, followed by the module’s IP address

Once the PC discovered the module, double click on the icon to open the module’s web client.

Enter your User ID and Password to login and click ‘Connect’ to connect.

Spot™ Monitoring Module

[11]

2.3

Camera Management

The Camera Management menu allows you to search, register and manage your IP cameras, DVRs and

NVRs. See “3.2 Camera Registration” for more information.

Search (DVR/NVR)

The module will scan the network for all supported DVR/NVR. Select the devices you wish to register

from the search results and press the ‘GET INFO’ button.

‘DETAIL INFO’ allows you to get more information on the device’s streams.

Enter the user ID and password for the devices you are registering.

You can also select which channels to register.

Click ‘APPLY’ to register the device.

Search (CAM)

The module will scan the network for all supported IP cameras automatically. From the results, you can

drag cameras to the viewing channel to assign them to channels.

5. Click the START button to search the camera.

6. Select a camera and while clicking on the camera, drag it to a channel to assign it. If needed,

enter the user ID and password for the device you are registering.

7. Click the CLOSE button to finish the process.

User Manual

[12]

2.4

Finish

Complete the setup of your module by registering your product.

When the setup wizard is completed, click the FINISH button to close the setup wizard.

3.

Operation

3.1

User Log-in

Enter the user ID and password. Use the hint button to check for your password hint if needed.

Note

1) The login window displays permanently until a user logs in with the right user ID and

password.

2) If the module is set as AUTO LOGON, the login process is not necessary. See “4.1.2 User”

for more information.

Note

The key in the virtual keyboard includes common words, such as Admin, root, http://,

rtsp://, www., .com, .net, .org etc.

Spot™ Monitoring Module

[13]

3.2

DVR/NVR/CAM Registration

Recorder Connection through the Network

The module will scan the network for all supported DVR/NVR automatically. Select the DVR/NVR you

wish to register from the search results and press the ‘GET INFO’ button to obtain the device’s

streaming profile. ‘DETAIL INFO’ allows you to get more information on the device’s streams. If

necessary, enter the user ID and password for the device you are registering. You can also select which

channels from the DVR/NVR you wish to register. Click ‘APPLY’ to register the device.

Camera Connection through the Network

1. Click the START button to search the camera. The module will search the network for

cameras and display all results in the table on the right.

2. Select the camera in the list and drag and drop it to the channel you want to assign to the

camera. (While moving, the mouse pointer is changed to ).

3. Click the CLOSE button to save the registration.

Add DVR/NVR Manually

If a user wants to connect to DVR/NVR in a different network, DVR/NVR can be added manually using

the ADD DVR/NVR MANUALLY button.

1. Click the SEARCH button to open the camera property window.

User Manual

[14]

2. Select channel number to register.

3. Input necessary information with button and click the GET INFO button to get streams

information.

4. Select the channel to register.

5. Click the APPLY button to register DVR/NVR.

Manually add Cameras

If a user wants to connect to an IP camera in a different network, the cameras can be added

manually using the ADD CAMERAS MANUALLY button.

1. Click the ADD CAMERAS MANUALLY button to open the camera property window.

2. Select channel number to register.

3. Select protocol (ONVIF, RTSP, FOCUS and VHT) of the camera. Registration is available with

one of the following. – IP Address, RTSP URL or ONVIF URL

4. Input necessary information with button and click the GET STREAM button to get streams

information.

5. Click the APPLY button to register the camera.

Adding a recorder or camera using RTSP

1. Click on the ADD CAMERAS MANUALLY button.

2. Enter the DVR’s user ID and password.

3. Select which channel you want to add to the Spot Monitoring Module.

4. Under Protocol, select RTSP instead of ONVIF (default).

5. Enter the DVR’s model and brand names (optional).

6. Enter the DVR’s RTSP URL in the first RTSP field.

a. To add DW’s VMAX® A1™ DVR, the RTSP URL should be as follow:

rtsp://xxx.xxx.xxx.xxx:port/rtsp/unicast/live/profile-x

For example: rtsp://192.168.1.100:80/rtsp/unicast/live/profile-1

7. Enter the device’s IP address: xxx.xxx.xxx.xxx.

8. Port: Use the device’s web port (default value is 80).

9. Profile-x: Enter the channel number you want to add.

10. Press the APPLY button to save changes.

Spot™ Monitoring Module

[15]

3.3

Deleting Devices

1. Click the delete ( ) button for deleting each DVR/NVR or camera.

2. Click the DELETE PAGE for deleting devices on the same page and click the DELETE ALL for

deleting all devices.

3.4

Live Display Mode

Channel Selection

The live image can be seen by easy button operation after power-up. The images can be seen in 1, 4, 9

and 16 screen splits (some split options may not be available according to the module’s number of

channels). Whenever the screen display mode button ( ) on the toolbar is clicked, the

screen will change to display the next channel or sequence of channels.

To switch from a multi-channel view to a single camera, click on the selected channel. To return to the

previous screen mode, click on the left mouse button again.

“VIDEO LOSS” is shown on the display screen when no camera is connected or disconnects suddenly.

When a camera is disconnected, a warning sound shall be generated depending on the system setting.

Admin users can set different levels of authorization for each user, granting them specific access to

specific channels. If a certain user is not authorized to view a channel, no image is shown on the display

screen as below.





User Manual

[16]

Icons

The Spot Monitoring Module shows the channel’s current status based on the settings in the DVR or

NVR.

Icons at the right-upper corner on each

channel screen

Icons at the right-bottom corner on fullscreen

Continuous Recording

No HDD detected

Motion Detection Recording

Emergency Recording is in use

Sensor Activated Recording

PTZ is enabled

Continuous + Motion Alarm

Recording

Warning for exceeding the set

temperature

Continuous + Sensor Activated

Recording

Sequence mode is enabled

Motion Detection + Sensor

Activated Recording

Digital zoom is enabled

Sensor Activated

Motion Detected

Audio Channel

PTZ Camera

Note

If you cannot find any recording icon in the right corner of the screen, then the system is not

recording. Check the recording schedule or camera in the main setup menu.

Pop-up Menu

Users can click the right button of the mouse to pop up sub-menu as below. If the user wants to

control a specific channel, put the mouse cursor on that channel and then click the right button.

Display Mode

Users can change the screen display mode from the available split options.

Change Next CH

View the next channel or next group of cameras in the current split

mode.

Sequence

When “SEQUENCE” is selected, icon will appear on the right-

bottom corner of the screen. The display screen will be sequentially

changed.

Digital Zoom

• Digital Zoom is available in a single-channel view only. When

“ZOOM” is selected, icon will appear on the bottom-right

corner of the screen and digital zoom control is available.

• To zoom in, drag the mouse’s cursor on the desired area to create

a zoom box. You can also control zoom-in and zoom-out by mouse scrolling the mouse’s

wheel up and down. Once the image is zoomed-in, the user can move the zoom area by

clicking on the edge of the square and dragging it.

Spot™ Monitoring Module

[17]

• To exit from the zoom mode, click the right and select “ZOOM EXIT’ on the menu.

PTZ

Enable PTZ mode. (Please refer to “3.6 PTZ Operation” for detail.) The available PTZ options

depend on the camera’s ONVIF integration. See the camera’s manual for more information.

Freeze

Freeze the current live view. System clock (date/time information) will continue running at the

bottom of the screen. Select “FREEZE” again to resume the live view.

Camera Setup

View the setup camera menu.

Users can setup resolution, frame, etc. The available options depend on the camera’s ONVIF

integration. See the camera’s manual for more information.

1. Click the GET STREAM button and get the current camera status.

2. Click the CAMERA INFO button to check the camera’s information such as model name, IP

address, port, MAC Address, etc.

3. MAINTENANCE – User can camera reset, reboot, firmware upgrade and setup to use the live

buffering function on NVR.

Reset

• Soft Reset: Reset camera settings except for basic network settings like IP address,

subnet and gateway or DHCP settings.

• Hard Reset: Reset all camera settings (factory reset).

Reboot

- Reboot the camera

Scheduled Reboot: Set the schedule to reboot the camera

F/W Upgrade

: Upgrade the camera firmware

User Manual

[18]

Network

: Set the camera network setting.

System Status

See the system status, including information on the network condition, the number of clients

currently connected to the module, etc. A green line means the connection is live and working.

Menu

Open the main menu setup screen.

Spot™ Monitoring Module

[19]

4.

Setting

The general setting structure consists of “System”, “Monitoring”, and “Network”. Each Setup menu

consists of sub-menus and additional categories.

Main Classification

Sub Classification

SYSTEM

INFORMATION

USER

DI SP LAY

SETTINGS

MONITORING

REGISTRATION

NETWORK

DDNS

To access the setup menu, click the button in the menu bar or right-click anywhere on the

screen and select the Setup Menu.

User Manual

[20]

4.1

System

Information

Site Name

Enter a site name to differentiate the module from other sites.

Date/Time

Using the available options, manually adjust the date and time, select the display mode for the time

and the date, and select the appropriate time zone. If applicable, check the ‘USE DST’ box.

There are four types of time sync modes:

• Server Mode: The operating module is set as a Time Sync Server, which can synchronize the

time to another module (s) connected over the same network.

• Client Mode: Input the IP address of a designated module or PC running Remote Software as

a Time Sync Server in “SYNC SERVER”. The module’s time clock will be synchronized with

the server by interval time set in “TIME SYNC CYCLE”.

• NTP Mode: “pool.ntp.org” is the recommended NTP Server. To activate, set the TIME ZONE of

your local area and then click the SYNC NOW button.

• GPS Mode: Connect USB type GPS device and click the SYNC NOW button.

Page is loading ...

Digital Watchdog Spot DW-HDSPOTMOD16 User manual

This manual is also suitable for

Digital Watchdog Spot DW-HDSPOTMOD16 User manual

Related papers

Other documents