Barco F50 Panorama User guide

Projector Toolset

User guide

For F- se ries

R5905904/03

31/08/2017

Barco NV

President Kennedypark 35, 8500 Kortrijk, Belgium

Phone: +32 56.36.82.11

Fax: +32 56.36.883.86

Support: www.barco.com/en/support

Visit us at the web: www.barco.com

PrintedinBelgium

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not

limited to the implied warranties or merchantability and ﬁtness for a particular purpose. Barco may make im-

provements and/or changes to the product(s) and/or the program(s) described in this publication at any time

without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made

to the information in this publication; these changes are incorporated in new editions of this publication.

The latest edition of Barco manuals can be downloaded from the Barco web site w

ww.barco.com or from the

secured Barco web site h

ttps://www.barco.com/en/signin.

be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights

of their respective holders. All brand and product names mentioned in this manual serve as comments or

examples and are not to be understood as advertising for the products or their manufacturers.

Table of contents
TABLE OF CON TENTS
Basic concepts ................................................................................... 3
1 Introduction .................................................................................................... 3
2 About a Conﬁguration ........................................................................................ 3
3 About a Snapshot............................................................................................. 3
4 About storing Conﬁgurations and Snapshots .............................................................. 4
Installation ......................................................................................... 5
1 General requirements ........................................................................................ 5
2 Free download of Projector Toolset ......................................................................... 6
3 Projector Toolset installation ................................................................................. 6
4 Starting up ..................................................................................................... 8
5 Manual installation of a device plug-in......................................................................10
6 Uninstall Projector Toolset ...................................................................................12
7 About this manual.............................................................................................13
Menus ............................................................................................... 15
1 General.........................................................................................................15
2 Menu and button bar..........................................................................................15
3 Main window...................................................................................................16
4 Short cut keys .................................................................................................17
5 Workspace Explorer ..........................................................................................18
6 How to adjust a setting .......................................................................................18
7 About Projector Toolset.......................................................................................19
8 Snapshot management.......................................................................................22
8.1 About snapshots.........................................................................................23
8.2 Managing snapshots ....................................................................................23
8.3 Take a snapshot .........................................................................................24
8.4 Apply a snapshot ........................................................................................26
8.5 Delete a snapshot .......................................................................................27
8.6 Add shot cut key to a snapshot ........................................................................28
8.7 Remove shot cut key association......................................................................29
Preferences ........................................................................................ 31
1 Introduction ....................................................................................................31
2 Start up the preferences......................................................................................31
3 Access level ...................................................................................................32
4 Software Appearance.........................................................................................33
5 Bug report setup ..............................................................................................36
6 Logging.........................................................................................................38
7 Settings ........................................................................................................39
8 Workspace selection..........................................................................................40
Conﬁgurator ....................................................................................... 43
1 Introduction ....................................................................................................43
2 Conﬁgurator window..........................................................................................43
3 Create a new conﬁguration ..................................................................................43
4 Add device to a conﬁguration via scanning ................................................................45
5 Add projector to a conﬁguration .............................................................................47
5.1 Add projector.............................................................................................48
5.2 General properties ......................................................................................48
5.3 Connection setup........................................................................................49
5.3.1 Set up a serial connection ........................................................................49
5.3.2 Set up an Ethernet connection ...................................................................51
5.4 Decorator setup..........................................................................................54
6 Reconnect a projector ........................................................................................54
7 Edit projector properties......................................................................................55
8 Conﬁguration preview ........................................................................................56
9 Conﬁguration properties......................................................................................56
R5905904 PROJECTOR TOOLSET 31/08/2017
1

Table of contents
10 Preview layout properties ....................................................................................57
10.1 Background color........................................................................................57
10.2 Background image ......................................................................................60
10.3 Rearrange pictographs in preview pane ..............................................................62
General projector settings ..................................................................... 63
1 Projector information..........................................................................................63
2 Basic control, Lamp ON-OFF................................................................................63
3 Basic control, Shutter.........................................................................................64
4 Basic control, OSD feedback ................................................................................64
5 Input selection.................................................................................................65
6 Advanced settings, start up ..................................................................................65
7 Advanced settings, control...................................................................................66
8 Maintenance, restore factory defaults ......................................................................67
Installation ......................................................................................... 69
1 Image orientation..............................................................................................69
2 Lens control....................................................................................................70
2.1 Speed of a control.......................................................................................70
2.2 Lens shift.................................................................................................70
2.3 Lens mid position........................................................................................70
2.4 Lens zoom ...............................................................................................71
2.5 Lens focus................................................................................................71
2.6 Lens Iris control..........................................................................................72
3 Scaling .........................................................................................................73
4 Test pattern ....................................................................................................73
5 Lamp - Illumination............................................................................................74
Adjustment ........................................................................................ 77
1 Picture..........................................................................................................77
2 Gamma.........................................................................................................77
3 3D settings.....................................................................................................78
Direct communication .......................................................................... 79
1 Send............................................................................................................79
Remote ............................................................................................. 81
1 Remote keyboard .............................................................................................81
Lens calculator ................................................................................... 83
1 Introduction ....................................................................................................83
2 Launching the lens calculator................................................................................83
Service mode ..................................................................................... 85
1 Service mode start up ........................................................................................85
2 Standard Maintenance .......................................................................................85
3 P7 calibration..................................................................................................85
4 P7 Common ...................................................................................................88
2
R5905904 PROJECTOR TOOLSET 31/08/2017

1. Basic concepts

1. BASIC CONCEPTS

Overview

• Introduction

• About a Conﬁguration

• About a Snapshot

• About storing Conﬁgurations and Snapshots

1.1 Introduction

Overview

Projector Toolset is a software tool to set up, conﬁgure, manage and control Barco projectors.

The concept of this Projector Toolset software is modular. The basic package can be extended with sev-

eral optional device plug-in modules, now and in the future available.

The Projector Toolset software works with conﬁgurations that can be loaded. Within a conﬁguration, differ-

ent snapshots can be taken. A snapshot represents a current state of a conﬁguration and can be reloaded

to return to this typical state. These terms will be used through the complete software.

Projector Toolset is a stand-alone application that runs on a Java Virtual Machine and that does not require

extraservicestorun.

Several conﬁgurations can be controlled simultaneously. Even when the conﬁgurations are connected via

different ways.

Screenshots through out the manual are only given as information. The content can be

slightly different with the current Projector Toolset version, or connected projector.

1.2 About a Conﬁguration

What is a Conﬁguration?

A Conﬁguration is a collection of projectors with all their current settings, connected to a computer. A

conﬁguration can contain different settings, called snapshots, for all the projectors in the conﬁguration.

1.3 About a Snapshot

What is a S napshot?

A Snapshot is collection of settings of a conﬁguration. Such a snapshot represents the current state of a

conﬁguration.

A snapshot can contain all settings or speciﬁc settings as input settings, lamp settings, layout settings or

projector settings. When restoring a snapshot, only the stored settings will be restored. The others remain

on their current value.

R5905904 PROJECTOR TOOLSET 31/08/2017

3

1. Basic concepts

1.4 About storing Conﬁgurat ion s and Snap shots

Overview

All information is stored by default in the install directory of Projector Toolset in the subdirectory Workspace.

Conﬁgurations are directly under the subdirectory Workspace and have the extension .conﬁg. Snapshots

are stored in a subdirectory of Workspace, called Snapshots.Theﬁles have the extension .snapshot .

This structure makes it possible to zip the workspace and send it the another computer for further use.

Tomakeabackupofallyourconﬁgurations and snapshots, just make a copy of Workspace with all its

content.

4

R5905904 PROJECTOR TOOLSET 31/08/2017

2. Installation

2. INSTALLATION

Overview

• General requirements

• Free download of Projector Toolset

• Projector Toolset installation

•Startingup

• Manual installation of a device plug-in

• Uninstall Projector Toolset

• About this manual

2.1 General requiremen ts

Before you begin

It assumes you are familiar with the computer system at your site.

System requirements for Microsoft Windows

Minimum hardware speciﬁcations :

• PC Pentium III or equivalent, 1 GHz

•512MBRAM

• Free hard disk space: 80 MB

• XGA resolution (1024 x 768) (recommended : SXGA resolution (1280 x 1024) with 32 MB video mem-

ory but better is for some advanced features to have the same resolution as the projector.)

• Serial communication port and/or Ethernet connection

Software

• Windows XP Home or Windows XP Professional, Windows Vista, Windows 7, Windows 8.

System requirements for Linux

Software

• Any Linux distribution that supports Sun’s Java Runtime Environment v1.5.0 (RedHat 9.0, SuSe 8.2,

Debian/Ubuntu, Mandriva, ...)

Check out the documentation of your favorite distribution to ﬁnd out if Java 1.5 is supported.

Minimum hardware speciﬁcations

• PC Pentium III or equivalent, 1 GHz

•512MbRAM

• Freeharddiskspace: 100MB

• XGA resolution (1024 x 768) (recommended : SXGA resolution (1280 x 1024) with 32 MB video mem-

ory but better is for some advanced features to have the same resolution as the projector.)

• Ethernet connection (serial connection is not supported)

Mac OS X

Software

• Apple’s Java SE 5.0 Release 3 or better

• Mac OS X v10.4.2 or better

R5905904 PROJECTOR TOOLSET 31/08/2017

5

2. Installation

Minimum system requirements :

•PowerPCG3

•256MBRAM

•10MBdiskspace

• Display with XGA resolution (1024x768) (recommended : Display with SXGA resolution (1280x1024)

but better is for some advanced features to have the same resolution as the projector)

• Network connection

2.2 Free download of P rojector Toolset

Overview

The program and all necessary plug-ins can be downloaded for free from Barco’s website, (URL:

h

ttp:www.barco.com). Once on the home page, go to Partnerzone to enter the partnerzone. Registration

is necessary.

If you are not yet registered, click on Sign up My.barco and follow the instructions. With the created lo-

gin and password, it is possible to enter the partnerzone where you can download the Projector Toolset

software and the device plug-in updates.

When downloading the complete Projector Toolset, this software contains already the latest device plug-

ins.

It is not necessary to install any other software. A Java virtual machine is included with this download.

2.3 P rojector Toolse t installation

The installation ﬁle contains the Projector Toolset framework and the a vailable plug-ins.

Do not install over an existing install, install in a new directo

ry or uninstall ﬁrst the pre-

vious version.

To install on Microsoft Windows

The process of installing your software involves the following s

teps:

1. Browse to the directory where the install program is downloaded.

2. Double click on Ptoolset_Installer.exe .

The installation starts. Depending on the local Internet Explorer settings, it is possible that a warning is

displayed. Just click Run to start the installation.

3. Follow the instructions given in the different install windows.

4. Complete installation is automatic.

Note: A restart of the computer is necessary before the software can be used.

Barco → Projector Toolset → Projector Toolset item is added to the program list (unless otherwise

selected during the installation).

6

R5905904 PROJECTOR TOOLSET 31/08/2017

2. Installation

Only Projector Toolset framework is installed. To start using it, ﬁrst install one or more

device plug-ins. The software will request to install the plug-ins.

To install on M AC OS X

The process of installing your software involves the following steps:

1. Browse to the folder where the downloaded installer zip ﬁle is stored.

2. Double click on the zip ﬁle to unzip.

3. Double-click on the PToolset_Installer ﬁle.

Theinstallationstarts.

4. Follow the instructions given in the different install windows.

5. The complete installation is done automatically.

Only Projector Toolset framework is installed. To start using it, ﬁrst install one or more

device plug-ins. The software will request to install the plug-ins.

To install on Linux

The process of installing your software involves the following steps:

1. Browse to the folder where the downloaded installer ﬁle (PToolset_installer .bin) has been stored.

2. Check if the ﬁle is executable. This is done by right clicking on the ﬁle and selecting ‘Properties’ from

the popup menu.

3. Select tab Permissions and check if Is executable is enabled.

Image 2-1

File properties

4. Double click on the Ptoolset_installer.bin to st

art the installation.

5. Follow the instructions given in the different install windows.

6. The complete installation is done automatically.

Only Projector Toolset framework is installed. To start using it, ﬁrst install one or more

device plug-ins. The software will request to install the plug-ins.

R5905904 PROJECTOR TOOLSET 31/08/2017 7

2. Installation

2.4 Starting up

Launching Projector Toolset on Microsoft Windows

To start up the Projector Toolset software:

1. Click on Start → Programs and select Barco → Projector Toolset → Projector Toolset.

Or,

if a desk top icon is available, double click that desk top icon.

The software starts up. This start up procedure can take a while. First splash screen opens.

Image 2-2

Start u p splash s creen

The software starts up with the latest used conﬁguration or, if new plug-ins or updated plug-ins are

downloaded, with overview table of the downloaded plug-ins. All plug-ins in the table are selected by

default.

Image 2-3

Overview downloaded plug-ins

2. Unselect the plug-ins which you do not want to install.

Or,

click on Unselect all and then select the plug-ins you want to install.

Select all will check all plug-ins at once.

8

R5905904 PROJECTOR TOOLSET 31/08/2017

2. Installation

3. Click OK to install the selected plug-ins.

When all plug-ins are installed, a restart message is displayed.

Image 2-4

Plug-ins installed

4. Click Yes to shutdown the application and restart the application.

Click No to continue working with the old plug-ins.

Launching Projector Toolset on Mac OS X

To start the Projector Toolset software on Mac OS X system:

1. With Finder, go to the Applications folder under your home folder.

2. Double-click on the Projector_Toolset icon to start the application.

It can take a while to start up. First splash screen opens.

The software starts up with the latest used conﬁguration or, if new plug-ins or updated plug-ins are

downloaded, with overview table of the downloaded plug-ins. All plug-ins in the table are selected by

default. (image 2-3)

3. Unselect the plug-ins which you do not want to install.

Or,

click on Unselect all and then select the plug-ins you want to install.

Select all will check all plug-ins at once.

4. Click OK to install the selected plug-ins.

When all plug-ins are installed, a restart message is displayed. (image 2-4)

5. Click Yes to shutdown the application and restart the application.

Click No to continue working with the old plug-ins.

6. Once Projector Toolset is fully started, it has the following look and feel.

Image 2-5

Look and feel on MAC

R5905904 PROJECTOR TOOLSET 31/08/2017 9

2. Installation

Launching Projector Toolset on Linux

To start the Projector Toolset software on a Linux system:

1. Go to your home folder.

2. Double click on the Projector_Toolset icon to start the application.

It can take a while to start up. First splash screen opens.

The software starts up with the latest used conﬁguration or, if new plug-ins or updated plug-ins are

downloaded, with overview table of the downloaded plug-ins. All plug-ins in the table are selected by

default. (image 2-3)

3. Unselect the plug-ins which you do not want to install.

Or,

click on Unselect all and then select the plug-ins you want to install.

Select all will check all plug-ins at once.

4. Click OK to install the selected plug-ins.

When all plug-ins are installed, a restart message is displayed. (image 2-4)

5. Click Yes to restart the application.

Click No to continue working with the old plug-ins.

6. Once Projector Toolset is fully started, it has the following look and feel.

Image 2-6

Look and feel on Linux

2.5 Man ual in stallation of a device plug-in

When sho uld it be done manually

When a new plug-in is downloaded, and the user has decided no to install it yet for some reason. He still

has the possibility to install this plug-in manually.

10

R5905904 PROJECTOR TOOLSET 31/08/2017

2. Installation

How to install

1. Start up Projector Toolset.

2. Click Help onthemenuandselectInstall plugin... .

Image 2-7

Install plug-ins, start

An Install device plug-in dialog box opens.

3. If the path and ﬁle name is known, ﬁll it out next to Select a tpi ﬁle.

Or,

click on the Browse button (...).

An Open dialog box opens.

4. Browse to the desired plug-in ﬁle and click Open.

Plug-in ﬁles are .tpi ﬁles and are mostly located in the Plugins subdirectory of Projector Toolset’s install

directory.

The Install device plug-in dialog is re-displayed with the complete path ﬁlled out.

5. Click Next.

An overview of projector name, plug-in ID and version is given.

A question dialog box appears to ask if you really want to install the selected plug-in.

6. Click Next to continue.

Installation procedure starts. Result is displayed in a dialog box. A restart of Projector Toolset is nec-

essary to activate the new installed plug-in.

R5905904 PROJECTOR TOOLSET 31/08/2017

11

2. Installation

7. Check Shutdown application and click Finish.

Image 2-8

Finish the installation

Projector Toolset will be closed.

8. Restart Projector Toolset.

The new plug-in is activated.

2.6 Uninstall Projec tor To olset

How to uninstall on a M icrosoft Windows platform

To uninstall the program, normal Windows functionality can be used to remove a software.

Click on Windows Start, select Settings and open Add/Remove software.

Select the version of Projector Toolset whi

ch must be removed and click on Remove.

The complete program will be removed from the hard disk.

How to uninstall on a Linux platform

Remove the Projector Toolset folder from the home folder.

How to uninstall on a Mac OS X platform

Remove the Projector Toolset folder from the application folder in the home folder.

12

R5905904 PROJECTOR TOOLSET 31/08/2017

2. Installation

2.7 Abo ut this manual

Overview

This Reference manual provides detailed information about the conﬁguration and setup software Projector

Toolset. This manual is designed to be a reference tool in your everyday work with Projector Toolset.

The following icons are used in the manual :

Caution

Warning

Info, term deﬁnition. General info about the term.

Note, gives extra information about the described subject.

Tip, gives extra advice about the described subject.

Images given in the manual are used as illustration. The content of the image can be slightly different with

the real image on the screen, e.g. version numbers, installed modules, etc. .

Typography:

• Clickable menu items or buttons are indicated in bold, e.g. OK

• Menu items are indicated in italic.

• A dialog window is indicated in italic, e.g. Make a new conﬁguration.

• Step related notes, tips, warnings or cautions are printed in italic.

• Procedure related notes, tips, warnings or cautions are printed in bold between 2 lines preceding by

the corresponding icon.

About the illustrations

The software is used to control different devices. The same function is sometimes uses in the GUI but

this GUI indicates another device name or pictograph depending on the connected device. Therefore, the

screenshots given as illustrations in this manual will show only one typ

e of device, independently which

device is connected, except if the way of working is different for the connected device.

What’s next?

Now that you are familiar with the style of this guide, you are now ready to know more about its modules

and what they can do.

R5905904 PROJECTOR TOOLSET 31/08/2017

13

2. Installation

14 R5905904 PROJECTOR TOOLSET 31/08/2017

3. Menus

3. MENUS

Overview

• General

• Menu and button bar

• Main window

•Shortcutkeys

• Workspace Explorer

• How to adjust a setting

• About Projector Toolset

• Snapshot management

Illustrations given in this chapter are only given as information. Depending on the pro-

jector type, t he real GUI can be slightly different with the illustrations but the functions

are the same and are located on the same position as in the illustration. The name of

the proje ctor is only used as illustration but can be any type of projector.

3.1 General

The right mouse button

The right mouse button is used in Projector Toolset for direct controls. The use of this button can be handy

throughout the complete software.

Ergonomics

Projector Toolset works on the principle of windows with adjustable sizes that can be positioned as you

like.

When Projector Toolset opens, it displays the main window along with the Menu and button bar. The

drop-down menus include the usual functions of any software (File,etc.) and menus speciﬁc for Projector

To o ls e t.

The button bar allows switching between the different modules.

An extra Workspace explorer window makes conﬁguration management more easy.

3.2 Me nu a nd button bar

Structure

The menu contains drop down menus accessible by clicking with the mouse on an item. To select an item,

justclickonaniteminthedropdownlist.

The button bar contains on the left side navigation buttons to the different modules and on the right side

manage buttons to the workspace explorer and snapshot function.

To activate a module, click on a navigation button. The window will change accordingly. When activating

some buttons, some extra items will be added to the menu.

R5905904 PROJECTOR TOOLSET 31/08/2017

15

3. Menus

Image 3-1

Menu and bu tton bar

3.3 Main window

Overview

The content of the main window changes when a other navigation (module) button is activated, but the

main parts are the same for all modules.

Image 3-2

Main window indications

Indica-

tion

Description

A Window title. Construction of active module - Conﬁguration name

BMenu

C

Module navigation buttons

D

Conﬁguration preview pane

E

Log window. Can be hidden by the log information button on top of the conﬁguration preview

pane.

16

R5905904 PROJECTOR TOOLSET 31/08/2017

Page is loading ...

Barco F50 Panorama User guide

Barco F50 Panorama User guide

Related papers

Other documents