Fortress Technologies FWAD10M13 User manual

Brand: Fortress Technologies

Model: FWAD10M13

Category: Mobile air conditioners

Type: User manual

This manual is also suitable for

Before operating or installing the unit, please read this manual thoroughly and

Window Air Conditioner

User Manual

Model

FWAD08M13 FWAD10M13

FWAD13M13 FWAD19M13

retain it for future reference.

CONTENTS

1. SAFETY INSTRUCTION ..................................................................2

2. PARTS DESCRIPTION ...................................................................5

3. OPERATION INSTRUCTION ..........................................................6

4. INSTALLATION INSTRUCTION ......................................................13

5. TROUBLE SHOOTING .....................................................................16

6. SPECIFICATIONS ...........................................................................17

7. WARRANTY ..................................................................................... 18

You can find many helpful information on how to use and maintain the air conditioner

properly. Just a little preventive care on the parts can extend the life of the air conditioner.

Read the trouble shooting tips before call the service centre. Many common problems can

be solved by the chart of trouble shooting tips.

Contact the authorised service technician for repair or maintenance of this unit.

Contact the authorised service technician for installation of this unit.

The air conditioner is not intended for use by children or infirm people without supervision.

Children should be supervised to ensure that they do not play with the air conditioner.

If the power cord is damaged, it must be replaced by the manufacturer, the authorised service

technician or qualified person in order to avoid a hazard.

Make sure the unit power and the circuit breaker are turned off before cleaning and maintenance.

CAUTION

Read This User Manual

Please follow below instructions to prevent injury and property damage.

Meanings of symbols in this user manual.

WARNING

Always do this.

Never do this.

Do not change the power

cord length or share the

outlet with other appliances.

Ensure earthed effectively.

Disconnect the main power

if strange sounds, smell or

smoke comes from the unit.

Close the door while the

air conditioner is running.

Ventilate room before operating air

conditioner if there is a gas leakage from

another appliance.

It may cause electric shock or

fire due to heat generation.

Incorrect earthing may cause

electric shock.

It may cause fire and electric

shock.

It may affect the cooling

effectiveness.

It may cause explosion, fire and burns.

It may cause electric shock.

It may cause failure of machine

or electric shock.

It may cause fire and electric

shock.

It may cause electric shock or fire.

If the power cord is damaged, it

must be replaced by the manufac-

turer or an authorised service

centre or a qualified person in order

to avoid a hazard.

This could damage your health.

Incorrect installation may cause

fire and electric shock.

It may cause electric shock.

It may cause an explosion or fire.

It may cause failure and electric shock.

Do not operate with wet

hands.

Do not allow water to run

into electric parts.

Do not put the power cord

close to any heating

sources.

Do not damage or use an

unspecified power cord.

Do not direct airflow at

room occupants .

Always install circuit

breaker and a dedicated

power circuit.

Do not open the unit

during operation.

Do not put the power cord near

flammable gas or combustibles, such

as gasoline, benzene, thinner, etc.

Do not disassemble or modify the unit.

SAFETY INSTRUCTION

CAUTION

When remove the air filter,

do not touch the metal parts

of the unit.

It may cause an injury.

Do not clean the unit when

power on as it may cause

fire , electric shock or injury.

Windows opened may cause

wetting of indoor and soaking

of household furniture.

Switch off the main power

and the circuit breaker before

cleaning and maintenance.

Stop operation and close

the window in storm or

hurricane.

Be careful when unpacking and

installing. Sharp edges could cause injury.

Do not clean the air

conditioner inner with water.

The insulation will be degraded

if water enter the unit . It may

cause an electric shock.

This could injure the pet or

plant.

Do not put a pet or

plant to direct air flow.

Ventilate the room well when

used together with a stove,

etc.

An oxygen shortage may occur.

It may cause deterioration of

quality.

It may cause failure of product

or fire.

Do not use this air conditioner to

preserve precision devices, food,

pets, plants, and art objects.

Turn off the main power

when not using the

unit for a prolonged period.

If water enters the unit, turn the unit off and switch

off the circuit breaker. Isolate supply by taking the

power-plug out and contact a qualified service

technician.

It may cause failure of

appliance or accident.

Appearance may be

deteriorated due to change

of product color or

scratching of its surface.

Do not put anything

around air-inlets or inside

the air-outlet.

Do not use strong deter-

gent such as thinner but

use a soft cloth.

If bracket is damaged, it may

cause damage due to falling

of unit.

There is danger of fire or

electric shock.

Ensure the installation bracket of

the outdoor appliance is not damaged

due to prolonged exposure.

Do not put anything on the

power cord and ensure that the cord

is not compressed.

Operation without filter may

cause failure.

It contains contaminants and

could make you sick.

Ensure the filter is inserted

securely. Clean the filter

once every two weeks.

Do not drink water drained

from air conditioner.

Before operation

Usage

Cleaning and maintenance

Operating Temperature

1. Contact an installation specialist for installation.

2. Do not use a damaged or non-standard power cord.

3. Do not share the same outlet with other appliances.

1. Exposure to direct airflow for a long period of time could be hazardous to the

health. Do not expose occupants, pets, or plants to direct airflow for a long

period of time.

2. Due to the possibility of oxygen deficiency, ventilate the room when use together

with stoves or other heating devices.

3. Do not use the air conditioner for non-specified purposes (e.g. preserving precision

devices, food, pets, plants, and art objects), otherwise it could harm the property.

1. Do not touch the metal parts of the unit when removing the filter. Injuries may occur

when handling sharp metal edges.

2. Do not use water to clean the air conditioner inner. Water enter the unit can degrade

the insulation and may lead to electric shock.

3. Make sure the unit power and the circuit breaker are turned off before cleaning and

maintenance.

SAFETY INSTRUCTION

If the unit is operated beyond the conditions specified above ,it may cause a failure of the unit.

Cooling operation

Outdoor temp:

18-43 C

Indoor temp:

17-32 C

Notes: The indoor relative humidity should be less than 80%. If the unit is used in a condition with a

relative humidity over 80%, there will be condensed water on the appearance of the unit.

1. Front panel

2. Air filter

3. Frame

4. Cabinet

5. Air inlet grille (outdoor side)

6. Air outlet grille

7. Control panel

8. Power cord

9. Control panel cover

10. Remote control

PARTS DESCRIPTION

NOTE: The front panel and cabinet may be slightly different according to the models, but the

functions are the same. The following illustration is for explanation purpose only, the actual

shape of the machine may be slightly different.

Accessories

Seal

(Used on

drain joint)

Screw

Drain Joint

Drain Tray

1. Power cord conductors are distinguished according to color as follows (see Fig.1)

2. Please contact the manufacturer, its service agent or a qualified person when replace the power cord.

3. For the safety and protection, the unit is earthed through the power cord. The wall

outlet (Air-break switch)should be provided with reliable earth wire (see Fig.2).

4. The unit should be provided with an individual circuit and the circuit breaker/fuse

rating should be same as that of the power cord and wall outlet.

POWER

CORD

E-Earth wire, yellow/green

N-Neutral wire, blue

A-Active wire, brown

Fig. 1

Fig. 2

Air-break switch

Note:

Control Panel

Vent Control

The vent control is located above the control panel. The operation method is different

on different models (see the following figures).

For maximum cooling efficiency, CLOSE the vent. This will allow internal air circulation.

OPEN the vent to discharge stale air.

The control panel will look like the following:

CLOSE VENT OPEN

To open the vent, pull the lever toward

To close it, push it in.

To open the vent, set the lever to the right position

To close it, set the lever in the left position.

CLOSE OPEN

NOTE: The outline of the operation panel is based on typical model, the function is same with the actual

machine even some differences may exist in appearance.

OPERATION INSTRUCTION

POWER:

Press the POWER button to turn the unit on/off.

(The TIMER button controls the auto stop feature of the unit.)

OPERATION INSTRUCTION

MODE:

Press the MODE button to select the appropriate operating mode. The mode selection

including AUTO, COOL, FAN and DRY. The green indicator light beside the "MODE"

button will illuminate to identify the mode selected.

When the unit is under the DRY and AUTO mode, the fan speed cannot be adjusted. The

fan speed is LOW in DRY mode and MED in AUTO mode. (Some models without MED

speed, the fan speed will be HIGH in AUTO mode.)

TEMPERATURE SETTING UP:

Press the button to increase the set (operating) temperature of the unit.

Each time the button is pressed the temperature increases 1 C (Celsius scale).

Maximum setting is 30 C.

TEMPERATURE SETTING DOWN:

Press the button to decrease the set (operating) temperature of the unit.

Each time the button is pressed the temperature decreases 1 C (Celsius Scale).

Minimum setting is 17 C.

FAN:

Press the "FAN" button to activate the fan speed setting. Each press of the button

will alternate through HIGH, MED, LOW fan speed options.

The green indicator light beside the FAN speed option will illuminate to identify the fan

speed selected.

TIMER:

First press the Timer button, the indicator light besides word on illuminates. It indicates

the Auto Start program is initiated.

Press or hold the Up( ) or Down( ) to change the Auto time by 0.5 hour increments,

up to 10 hours,then at 1 hour increments up to 24 hours. The control will count down

the time remaining until start.

SWING:

Press the "SWING" button to activate the automatic oscillation feature. The

green indicator light adjacent to the "SWING" button will illuminate. The vertical louvers will

oscillate back and forth (side to side) automatically sweeping air alternately for comfortable

cooling. To stop the oscillation feature, press the "SWING" button again, the green

indicator light adjacent to the button will turn off.

Press the "SWING" button for 2 seconds will activate the SLEEP mode which can reduce

noise and create a comfortable sleeping environment.

OPERATION INSTRUCTION

DRY:

In the DRY mode, the air conditioner will generally operate in the form of a dehumidifier.

COOL:

The temperature setting are adjustable between 17 C to 30 C . Cooling begins auto-

matically when the room temperature is 1 C above the set point, and stops when the room

temperature is 1 C below the set point. The fan will remain running.

AUTO:

The fan speed is MED in AUTO mode.

(Some models without MED speed, the fan

speed is HIGH in AUTO mode.)

The unit will be operated in the appropriate mode

FAN or COOL based on the temperature difference between the actual and desired

room temperature. If the actual room temperature is 2 C above the set point, the unit be

operated in COOL mode. When the actual room temperature is not 2 C or higher above

the set point and not 1 C or lower below the set point, the unit will be operated in FAN

mode.

Note:

If activating the SLEEP mode when the unit is operated in AUTO mode, the fan speed will be changed into

LOW immediately.

SLEEP:

Press the "SWING" button for 2 seconds to activate/deactivate the "SLEEP" feature.

In the COOL mode, the cooling temperature set point will increase 1 C per hour after the

"SLEEP" mode is activated. Two hours later, the set point will not be changed and the fan

speed will be kept on LOW .

Note:

When activating the SLEEP mode in AUTO mode, the set temperature will not be changed over time.

OPERATION INSTRUCTION

Indicates frosting protection (Turn off the unit and restart it to return to normal operation).

Failure Indicator Display:

Indicates a malfunction of the indoor room temperature sensor

Indicates a malfunction of the evaporator temperature sensor

Indicates a malfunction of the outdoor condenser temperature sensor

Note: When one of the above malfunctions occurs, turn off the unit, and check for any obstructions.

Restart the unit, if the malfunction is still present, turn off the unit and unplug the power cord.

Contact the manufacturer or its service agents or a similar qualified person for service.

REMOTE CONTROL OPERATION

TEMP

AUTO

COOL

DRY

FAN

HIGH

MED

LOW

MODE

FAN SPEED

SWING

TIMER ON

SLEEP

ON/OFF

TIMER OFF

RESET LOCK

SET TEMPERATURE( C)

TEMP DOWN Button

Press the button to increase the set (operating)

temperature of the unit. Each time the button is

pressed the temperature increases 1 C (Celsius scale).

Maximum setting is 30 C.

TEMP UP Button

Press the button to decrease the set (operating)

temperature of the unit. Each time the button is

pressed the temperature decreases 1 C (Celsius Scale).

Minimum setting is 17 C.

Press the MODE button to select the appropriate

operating mode. The mode selection including

AUTO, COOL, FAN and DRY.

When the unit is under the DRY and AUTO mode,

the fan speed cannot be adjusted. The fan speed is

LOW in DRY mode and MED in AUTO mode.

(Some models without MED speed, the fan speed will

be HIGH in AUTO mode.)

MODE Button

SWING Button

TIMER ON :

Press the "TIMER ON" button to activate the auto on

time setting. Each press will increase the time setting

in 30 minutes increments, up to 10 hours, then at

1 hour increments up to 24 hours. To cancel the

auto on time setting, press the button until the time

setting is 0.

SLEEP Button

Press the "SLEEP" button to activate/deactivate the

"SLEEP" feature. In the COOL mode, the cooling temp

erature set point will increase 1 C per hour after the

"SLEEP" mode is activated. Two hours later, the set point

will not be changed and the fan speed will be kept on LOW .

Note: When activating the SLEEP mode in AUTO mode,

the set temperature will not be changed over time.

TIMER OFF :

CAUTIONS

Never immerse the remote control in water or other liquids. Do not put it under direct sunshine.

Remove the batteries in the remote control if it is not in use for prolonged period.

Use the remote control within a distance of 5 meters from the air conditioner. A sound of beep will be generated by the

air conditioner when signals received.

Press the "SWING" button to activate the automatic

oscillation feature. The green indicator light adjacent

to the "SWING" button will illuminate. The vertical

louvers will oscillate back and forth (side to side)

automatically sweeping air alternately for comfortable

cooling. To stop the oscillation feature, press the

"SWING" button again, the green indicator light

adjacent to the button will turn off.

RESET Button

Press the "RESET" button to cancel all of the

current settings.

ON/OFF Button

Press the "ON/OFF" button to turn the appliance

ON/OFF.

Press the "FAN" button to activate the fan speed setting.

Each press of the button will alternate through LOW, MED,

HIGH fan speed options.

FAN SPEED Button

LOCK :

Press the " TIMER OFF" button to activate the auto off

time setting. Each press will increase the time setting

in 30 minutes increments, up to 10 hours, then at

1 hour increments up to 24 hours. To cancel the

auto off time setting, press the button until the time

setting is 0.

Press the "LOCK" button to lock all current

settings and the remote control will not accept

any operation. Press the "LOCK" button again to

cancel the LOCK function.

If the signal receiver on the air conditioner is exposed to direct sunshine, the air conditioner may be not function properly.

TIMER ON OFF

SET TEMPERATURE

Transmission Indicator

Temp./Timer display

FAN SPEED display

MODE display

ON/OFF display

This transmission indicator will light when remote

control transmits signals to the main unit.

The temperature setting (from 17 C to 30 C) or

timer setting (0~24h) will be displayed.

If FAN mode is selected, there will be no display.

FAN MODE display

TIMER ON/OFF display

LOCK Indicator

Indicators on LCD

REMOTE CONTROL OPERATION

AUTO

COOL

DRY

FAN

HIGH

MED

LOW

NEVER operate the air conditioner without the

air filter, as dust/dirt particles can cause

equipment failure.

CAUTION

The air filter behind the inlet grille should be checked and

cleaned at least once every 2 weeks (or as necessary) to

maintain optimal performance of the air conditioner.

Air Filter

CONTROL PANEL COVER

Grasp the right of the control panel cover and

pull it upwards to open it .

Close the control panel cover and press the

right of the cover again until it snaps into the

locked position.

To adjust vertical air flow direction of the up or low horizontal

louvers, adjust any one of the up or low horizontal louver blades.

Manual vertical air flow adjustment

Always keep the top or bottom blades in horizontality. This can

prevent water drops condensed on the front panel of the unit.

OPERATION INSTRUCTION

How to remove the air filter

1. Hold the tabs under the front panel, then uplift it outwards,

and remove the front panel.

2. Pinch the handle under the air filter and make the air filter

arched, remove it from the slot from underside to upside.

3. Clean the filter with warm water. The water

should be below 40 C to prevent distortion of the filter.

4. Rinse off and gently shake off excess water from the

filter. Allow the filter to dry before re-install it. To prevent

distortion of the filter, do not dry it in direct sunlight.

Different requirement for different type of air

conditioner, there are two methods to treat the

condensed water.

See the following procedures to perform back drainage:

1. Fit the seal onto the drain joint (which is provided with

the air conditioner accessory).

Drainage

SEAL

DRAIN

JOINT

RUBBER

PLUG

RUBBER

PLUG

SCREW

DRAIN TRAY

DRAIN

OUTLET

2. Remove the rubber plug from the back of the unit

and insert the rubber plug into the bottom drain hole

of the unit.

3. Attach the drain joint to the back of the cabinet where you remove the plug and rotate 90

to securely assemble them.

4. Connect the drain joint with an extension drain hose .

1. Remove the rubber plug from the bottom of the cabinet and

attach to the back drain hole.

2. Take out the drain tray and screws (which are provided with

the air conditioner accessory).

3. Install the drain tray at the bottom of the unit and secure with

screws provided.

4. Connect the drain hose to the outlet located at one side of the

drain tray. You can purchase the drain hose or tubing locally to

satisfy your particular needs .

Suggestion: To ensure the condensed water drain off

smoothly, always keep the drain outlet of the the drain tray

downward when install the drain tray.

See the following procedures to perform bottom drainage:

If you choose non-drainage,both the bottom and the back drain hole of the unit should be

inserted with the rubber plug.

Note:

Bottom Drainage

Back Drainage

1. To avoid vibration and noise, make sure the unit is installed securely and firmly.

2. Install the unit where the sunlight does not shine directly.

If the unit is installed under direct sunlight, build an awning to shade the cabinet.

3. There should be no obstacle, such as a fence or wall, within 50cm from the back of the

cabinet because it will prevent heat radiation of the condenser.

Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner.

4. Install the unit a little obliquely outward not to leak the condensed water into the room

(about 10mm with level).

5. Install the unit with its bottom portion 75~150cm above the floor level.

6. The power cord must be connected to an independent circuit. The yellow/green

wire must be earthed.

Over 50cm

About 10mm

FENCE

AWNING

75-150cm

Over 50cm

About 10mm

FENCE

AWNING

75-150cm

* The appliance shall be installed in accordance with local wiring regulations.

All side louvers of the cabinet must remain exposed to the outside of the structure.

CAUTION

Select the best location

INSTALLATION INSTRUCTION

Installation of the unit into the Cabinet

Installation of the unit into the wall

1. Slide the unit into the cabinet until it is firmly against the

rear of the cabinet. Ensure the foam

sealing strips on the cabinet remain in position.

2. Connect the air conditioner to the power and put

excess cord on the air conditioner base.

3. Engage the chassis fixing brackets into the bottom cabinet

rail and secure to the base with the screw provided.

4. Remove the front panel from the carton and plastic bag

and fit as per the Installation lnstruction.

5. Switch unit on to check for operation of the unit and

vibration in the installation.

6. Fit the drain pan to the cabinet and run a drain tube to a

suitable location if required.

Alternative method of installation if external

support cannot be provided.

FLASH OR SEAL AROUND EXTERNAL

WALL FRAME OR ARCHITRAVE

STURDY TIMBER

FRAME

TIMBER FRAMED

WALL OR PARTITION

SOLID TIMBER SUPPORT

STEADYING BRACKET

(ONE PER SIDE)

DRAIN TRAY

ENSURE LOUVRES

ARE ENTIRELY

OUTSIDE THE WALL

Step 1

Remove the air conditioner from the package, remove fixing

screws and slide the air conditioner out from the cabinet (Refer

to Installation Steps).

Step 2

Drill holes in the wall to ensure the cabinet can be well

supported. Holes from the outside through to the cavity should be

sealed. The cabinet should slope down towards the rear by

about 10mm to allow water drainage during operation.

Step 3

Install and secure the cabinet into the wall. Ensure the foam

seals are not damaged. Flash, seal or fill gaps around the

inside and outside to provide satisfactory appearance and

protection against the weather, insects and rodents.

Installation of the Cabinet

NOTE: UNIT CAN BE SUPPORTED BY A

SOLID FRAME FROM BELOW OR

BY A HANGER FROM A SOLID

OVERHEAD SUPPORT.

Preferred method of installation into a timber

framed wall, partition or window.

FLASH OR SEAL AROUND EXTERNAL

WALL FRAME OR ARCHITRAVE

STURDY TIMBER

FRAME ALL ROUND

UNIT

TIMBER FRAMED

WALL OR PARTITION

EXTERNAL SUPPORT

FRAME AT BALANCE

POINT OF A/C

ALTERNATIVELY, BRACKETS

AS ILLUSTRATED BELOW

MAY BE USED.

DRAIN TRAY

Scrape

10mm

Less than C

more than D

More thanA

More than B

Less than

more thanA

Wall thickness is less than C

If the wall thickness is more than

scrape the wall as shown above.

Make rear side lower so that water will drain

out smoothly.

Size(mm)

200*

500

210

The minmum gap between the wall and the cabinet or air inlet louvers:

Position A is determined by

the specific model and

environment, however,

the installation distance

must not be less than 200 mm.

Step 2. Remove the frame.

1. Remove two fixing screws from the frame (See Fig.3).

2. Grasp the left corner of the frame's underside, release the coupler plugs,

then loosen the frame (See Fig.4).

Step 3. Installation.

1. Remove two fixing screws on the chassis fixing brackets, then remove the chassis fixing brackets

(See Fig.5).

2. Grasp the handle on the chassis and carefully slide the air conditioner out of the cabinet (See Fig.6).

3. Remove shipping pad from around compressor before operation and make sure the discharge points

to the drain pan are aligned before the chassis is pushed into the cabinet (See Fig.7).

4. Push the unit chassis into the cabinet (See Fig.8).

5. Install two chassis fixing brackets by two fixing screws (See Fig.5).

Step 4. Install the frame.

1. Install the frame and connect the coupler plugs, make

sure not to interfere with the temperature sensor cable

(See Fig.9).

2. Fix the screws on the frame (See Fig.3).

Step 5. Install the air filter and front panel.

1. Install the air filter into the frame's slot from upside to

underside (See Fig.2).

2. Hang the front panel on the frame's buckle, then press the

front panel into the frame's slot until you hear a click (See Fig10).

Installation Steps

Step 1. Remove the front panel and the air filter

1. Hold the tabs under the front panel, then uplift it outwards, and remove the front panel (See Fig.1).

2. Pinch the handle under the air filter and make the air filter arched, remove it from the slot from underside

to upside (See Fig.2).

Abnormal Operation

TROUBLESHOOTING

Normal Operation

Air conditioner

does not cool as

it should

Air conditioner

does not work

Air conditioner

freezing up

Problem

Possible Causes

What To Do

The air conditioner is

unplugged.

Make sure the air conditioner plug is pushed

completely into the outlet.

Troubleshooting Tips

Please review the chart first before you call for service.

You may hear a pinging noise caused by water being picked up and thrown against the

condenser on rainy days or when the humidity is high. This design feature helps remove

moisture and improve efficiency.

You may hear the thermostat click when the compressor turns on and off.

Water will be collected in the base pan during high humidity or on rainy days .The water may

overflow and drip from the outdoor side of the unit.

The fan may continue operation when the compressor is off.

The fuse is blown/circuit

breaker is tripped.

Check the house fuse/circuit breaker box and

replace the fuse or reset the breaker.

Power failure.

If power failure occurs, switch off and disconnect

/unplug the power cord. When power is restored,

reconnect (plug in) the power cord, switch on the

power and wait 3 minutes to restart the air

conditioner to prevent tripping of the compressor

overload.

Airflow is restricted .

Make sure there are no curtains, blinds, or

furniture blocking the front of the air conditioner.

Clean the filter at least every 2 weeks.

See the operating instruction section.

When the air conditioner is first turned on, it takes

some time for the room to cool down.

Check for open furnace floor registers and cold

air returns.

Set the air conditioner's vent to the closed position.

See Air Conditioner Freezing Up below.

The air filter is dirty.

The room was hot.

Cold air is escaping.

Cooling coils have iced up.

Ice blocks the air flow and

stops the air conditioner

from cooling the room.

Set the fan at MED or HIGH until the ice melts.

SPECIFICATIONS

TYPES(Btu/h)

BODY DIMENSION(mm)

(W x H x D)

WIRING SIZE

(mm )

< 9000

> 9000 and <12000

450x346x535

600x380x560

3*1.0

3*1.5

18000

660x428x680

3*2.5

1. The product has 3 years warranty from the date of purchase.

2. The warranty shall not apply:

A. To any Product subjected to accident, misuse, neglect, alteration, Acts of- God, improper handling,

improper transport, improper use, improper testing or unauthorized repair;

B. To cosmetic problems or defects which result from normal wear and tear under ordinary use, and do

not affect the performance or use of the product. All warranties are void if the product is opened, altered,

and/or damaged;

C. To any packing, transportation, export / import tax or any related expenses.

3. Customer must present the sales invoice or receipt for 3 years warranty services.

5. To prevent circuit overload and fire, no more than one adaptor or one extension unit should be inserted

into a socket outlet. (Do not connect other appliances to the socket outlet supplying an electric heater.)

No adaptor should be inserted into any extension unit or vice versa.

6. Stop using an adaptor or extension unit or socket if its socket holes cannot firmly hold a plug or if it is too

hard to insert a plug into it.

7. This appliance must be plugged into a specific socket for 220V with no less than 10A provided. Please

make sure the plug is fully plugged-in before use. Do not use any adapter or extension cord; Never use

the same supply socket for this appliance and other appliances at the same time, in order to avoid damage

to this appliance.

8. THE APPLIANCE IS FOR HOUSEHOLD USE ONLY

IMPORTANT NOTICES

IN NO EVENT SHALL OUR COMPANY OR THE SUPPLIER BE LIABLE TO YOU OR ANY OTHER PARTY

FOR ANY DIRECT, INDIRECT, GENERAL SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY OR

OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT (INCLUDING,

WITHOUT LIMITATION, DAMAGES FOR INJURY, LOSS OF PROPERTY, BUSINESS PROFITS, BUSINESS

INTERRUPTION) OR FROM ANY BREACH OF WARRANTY, EVEN IF OUR COMPANY OR SUPPLIER

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO CASE SHALL OUR COMPANY

OR SUPPLIER'S LIABILITY EXCEED THE AMOUNT YOU PAID FOR THE PRODUCT.

Specifications, designs and dimensions subject to change without prior notice.

4. All require for service,please contact Fortress Service Centre Hotline, Tel: 2555-5788

WARRANTY

Page is loading ...

Fortress Technologies FWAD10M13 User manual

Brand: Fortress Technologies

Model: FWAD10M13

Category: Mobile air conditioners

Type: User manual

This manual is also suitable for

Download PDF

report

Fortress Technologies FWAD10M13 User manual

This manual is also suitable for

Fortress Technologies FWAD10M13 User manual

Related papers

Other documents