Model FT7000
XP
QUICK REFERENCE GUIDE
TDN 07102-00071
THIS AREA FOR SERVICE PROVIDER
CONTACT INFORMATION:
04/2007
2
2. ENTER THE 2-DIGIT USER ID. PRESS <ENTER> KEY. ENTER THE USER PASSWORD AND PRESS <ENTER> KEY.
THE MANAGEMENT FUNCTIONS MAIN MENU IS DISPLAYED.
1. AT ATM WELCOME SCREEN, PRESS AND HOLD DOWN THE <CTRL> KEY (LOWER-RIGHT CORNER OF KEYPAD),
PRESS <1> KEY, THEN RELEASE BOTH KEYS. THE SECURITY LOGIN SCREEN WILL BE DISPLAYED.
- ACCESS INSTRUCTIONS -
MANAGEMENT FUNCTIONS
THE VIEW ATM SETTLEMENT TOTALS DISPLAYS THE TOTAL NUMBER OF
CAPTURED
CARDS AND DISPENSED CURRENCY WITH THE START AND END DATES.
THE START DATE IS THE LAST ATM SETTLEMENT RESET DAY AND THE END DATE
IS
THE CURRENT DATE. THE SETTLEMENT TOTALS ARE NOT CLEARED.
THE CLEAR ATM SETTLEMENT TOTALS RESETS ALL THE ATM SETTLE-
MENT TOTALS TO ZERO (0) AND RESETS THE START DATE TO THE CURRENT DATE/
TIME.
RESET ATM: FOLLOW A CCESS INSTRUCTIONS TO ENTER MANAGEMENT
FUNCTIONS. SELECT SYSTEM PARAMETERS, THEN RESTART TERMI-
NAL.
SHUTDOWN TERMINAL: FOLLOW ACCESS INSTRUCTIONS TO ENTER
MANAGEMENT FUNCTIONS. SELECT SYSTEM PARAMETERS, THEN
RESTART / SHUTDOWN TERMINAL
SHUTDOWN TERMINAL. NOTE: THIS OPTION POWERS DOWN THE PC ONLY!
!!
!!
! PRESS THE <ALT> AND “R” KEYS ON THE REAR KEYBOARD.
!!
!!
! WHEN PROMPTED, ENTER THE PIN NUMBER OF THE SETTLEMENT CARD.
!!
!!
! THE HOST/PROCESSOR SETTLEMENT SCREEN APPEARS. NOTE: OPTIONS
MAY VA R Y DEPENDING ON THE HOST.
VIEW / CLEAR ATM SETTLEMENT TOTALS
!!
!!
! FOLLOW ACCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SELECT TERMINAL SETTLEMENT
FUNCTIONS. CHOOSE VIEW ATM SETTLEMENT TOTALS. SELECT <PRINT> OPTION TO PRINT A REPORT.
REAR DISPLAY HOST SETTLEMENTS
3
THE DISPLAY LAST X FUNCTION IS USED TO DISPLAY AND PRINT RECORDS
FROM
THE ELECTRONIC JOURNAL. RECORDS PRINTED USING THIS COMMAND
ARE
NOT MARKED IN ANY WAY . THIS FUNCTION WILL NOT AFFECT ANY OTHER
JOURNAL
FUNCTIONS.
- DISPLAY LAST X -
!!
!!
! FOLLOW A CCESS INSTRUCTIONS TO ENTER MANAGEMENT FUNCTIONS. SE-
LECT TERMINAL SETTLEMENT FUNCTIONS. CHOOSE REPLENISH
CASSETTE(S).
!!
!!
! A SCREEN IS DISPLAYED THAT ALL CASSETTE(S) MAY BE REMOVED.
< FOLLOW THE CASSETTE REPLENISHMENT PROCEDURES >
!!
!!
! PRESS <1> TO RETURN TO TERMINAL SETTLEMENT FUNC-
TIONS.
!!
!!
! A SCREEN WARNING APPEARS THAT THE TIMEOUT FUNCTION NOR-
MALLY ASSOCIATED WITH MANAGEMENT FUNCTIONS IS DISABLED. PRESS
<1> TO CONTINUE.
!!
!!
! FOLLOW A CCESS INSTRUCTIONS TO ENTER MANAGE-
MENT FUNCTIONS. SELECT ELECTRONIC JOURNAL.
CHOOSE DISPLAY LAST X RECORDS.
REPLENISH CASSETTE(S)
THE REPLENISH CASSETTE(S) FUNCTION ALLOWS USER TO REPLENISH THE
MEDIA
(CURRENCY, COUPONS, ETC) IN THE CASSETTE(S).
ELECTRONIC JOURNAL
!!
!!
! PRESS <2>, PERFORM QUERY, TO DISPLAY THE RECORDS. SELECT <PRINT> OPTION TO PRINT THE REPORT.
!!
!!
! PRESS <1> TO HIGHLIGHT THE NUMBER OF RECORDS
TO
DISPLAY. ENTER AN AMOUNT (#), THEN PRESS <ENTER>
KEY.
Note: The Fujitsu 510 dispenser does not have the capability to
lock/unlock cassettes. Cassette(s) may be removed/inserted at any
time.
4
3
1
2
4
5
6
7
8
UNLOCK / OPEN CABINET.
REPLENISH CASSETTE(S) - NMD-100
STEP
ACTION
STEP
ACTION
GRASP NOTE CASSETTE
HANDLE
WITH ONE HAND
WHILE
HOLDING THE MECHA-
NISM WITH THE OTHER. PULL
THE
CASSETTE OUT
SLIGHTLY
, THEN PLACE ONE
HAND
UNDERNEATH AS YOU
SLIDE
IT OUT.
PLACE CASSETTE ON A LEVEL SURFACE. INSERT KEY
INTO
THE CASSETTE LOCK AND TURN CLOCKWISE. PRESS
GREEN RELEASE BUTTON TO RAISE LID.
MOVE PUSHER PLATE TOWARDS THE CASSETTE HANDLE.
PLATE SHOULD STAY INPLACE. LOAD NOTES USING 1" -
2" STACKS OF CURRENCY.
LEVEL NOTE PILE BY HAND. MOVE PUSHER PLATE
AGAINST
THE NOTES WITH ENOUGH PRESSURE TO HOLD
NOTES
BEFORE CLOSING.
EXTEND “PAWLS” FULLY (IN-
SERT) ON THE PUSHER PLATE.
CLOSE CASSETTE LID TO ITS
LOCKED
POSITION. THE
GREEN RELEASE BUTTON
SHOULD
“POP” OUT. TURN
KEY
COUNTERCLOCKWISE TO
LOCK
CASSETTE. SLIDE CAS-
SETTE INTO ITS SLOT IN THE
MECHANISM
.
REMOVE REJECT CASSETTE FROM MECHANISM. PLACE
ON
LEVEL SURFACE. INSERT KEY INTO LOCK AND TURN
CLOCKWISE
. PRESS GREEN RELEASE BUTTON TO RAISE
LID
.
REMOVE ANY REJECTED NOTES - BOTH SINGLE AND
BUNDLED
AREAS. FOLLOW LOCKING PROCEDURES FROM
STEP 6 AND SLIDE CASSETTE BACK INTO MECHANISM.
Single Note Reject
Area
Bundled Note Reject
Area
5
2
3
!!
!!
! PLACE CASSETTE ON FLAT SUR-
FACE.
""
""
" OPEN CASSETTE BY SLIDING
LATCH
LEVER TO RIGHT AND LIFT LID.
##
##
# FLIP LID BACK FULLY.
!!
!!
! MOVE PRESSURE PLATE
AGAINST
THE NOTES WITH ENOUGH
PRESSURE
TO HOLD NOTES BEFORE
CLOSING
LID.
""
""
" FOLD CASSETTE LID DOWN TO
ITS
LOCKED POSITION. INSERT CAS-
SETTE BACK INTO THE MECHANISM.
$$
$$
$ HOLD GREEN KNOB AND PULL
PRESSURE
PLATE BACK TOWARDS
REAR
.
%%
%%
% RELEASE KNOB AND ENSURE
PLATE
IS LATCHED.
&&
&&
& LOAD NOTES USING 1" - 2"
STACKS OF CURRENCY.
REPLENISH CASSETTE(S) - FUJITSU 510
STEP
1
!!
!!
! UNLOCK / OPEN CABINET.
""
""
" GRASP CASSETTE HANDLE AND
PUSH
GREEN RELEASE BUTTON.
##
##
# PULL CASSETTE OUT SLIGHTLY,
THEN PLACE ONE HAND UNDERNEATH
AS
YOU SLIDE IT OUT.
ACTION
Lid latch
REMOVE ANY REJECTED NOTES FROM
REJECT
AREA. NOTE: ONLY THE
TOP CASSETTE ACCEPTS REJECTS.
Release button
* IMPORTANT *
BEFORE INSERTING CASSETTES IN THE FEED CHAN-
NELS, ENSURE THE OPEN/CLOSE TAB (LOCATED IN
EACH
CHANNEL) IS IN THE “CLOSE” POSITION. THE
TAB
SHOULD BE IN THE POSITION SHOWN BELOW. IF
NOT
, BILL FEED ERRORS WILL OCCUR!
6
IF PAPER REMAINS ON ROLL, CUT
BETWEEN
THE ROLL AND INPUT TO
PRINTER
.
1
4
7
2
5
8
3
6
PUSH UP ON THE FEED BUTTON
(BLUE) REPEATEDLY TO ADVANCE
REMAINING
PAPER FROM FEED PATH.
ALIGN PAPER ROLL (W/SPINDLE) IN
PAPER
SUPPORT BRACKET SLOTS.
ENSURE PAPER FEEDS FROM BOT-
TOM!
PLACE SPINDLE IN NEW PAPER ROLL.
CUT OFF ANY PAPER WHERE THERE
IS
GLUE PRESENT.
REPLACE PAPER (RECEIPT PRINTER)
STEP
ACTION
STEP
STEP
ACTION
ACTION
PASS END OF PAPER OVER THE TEN-
SION ROLLER AND INSERT INTO THE
PRINTER
TAKE-UP SLOT. PRINTER
WILL
AUTOMATICALLY GRAB PAPER.
REMOVE EXISTING PAPER ROLL AND/
OR SPINDLE FROM PAPER SUPPORT
BRACKET
.
OPEN UPPER LEFT CABINET DOOR.
PULL UP ON THE LOCKING PIN AND
EXTEND
PRINTER ASSEMBLY TRAY
FULLY
.
Feed button
FROM REAR SERVICE PANEL - ENTER MANAGEMENT FUNCTIONS >
DIAGNOSTICS > PRINTER. SELECT OPTION <3>, RESET. THE
PRINTER
WILL RESET AND DISPLAY A STATUS REPORT. SELECT <PRINT>.
THE REPORT WILL PRINT TO THE RECEIPT PRINTER. PUSH PRINTER TRAY
BACK
INTO CABINET. THE PRINTER IS NOW READY.
7
PRINTER ACCESS AREAS
PAPER SPECIFICATIONS
!!
!!
!
""
""
"
##
##
#
$$
$$
$
GREEN MARKINGS ON ASSEMBLY ARE DESIGNATED ACCESS AREAS.
PAPER SPECIFICATIONS
htdiW)1-/0+(mm08"8/1-3
retemaiDmm452otpu"01otpu
)edisni(retemaideroCmm52~"1
)ylp(ssenkcihTrepaP
)snorcim5-/+26(
054DP
)snorcim4-/+16(053P
8
tnemeriuqeReziSepolevnE s
htgneL htdiW ssenkcihT
muminiM]"19.5[mm051]"57.3[mm59
]"72.[mm7
mumixaM]"6.9[mm442]"52.4[mm801
)mm1.832xmm8.401(epolevne01#asiezisdednemmoceR:etoN
THE OPTIONAL ENVELOPE SUPPLY UNIT HOLDS APPROXIMATELY 200 ENVELOPES. WHEN LOADING ENVELOPES, ALTER-
NATE EVERY 50-100 WITH THE FLAPS UP. FOR EXAMPLE, LOAD 50 WITH FLAPS UP FACING LEFT, THEN NEXT 50 WITH
FLAPS
UP FACING RIGHT. THE ENVELOPE SIZE REQUIREMENTS ARE AS FOLLOWS:
1. OPEN UPPER LEFT REAR CABINET DOOR. PULL UP ON TRAY LOCKING
PIN
AND PULL THE ENVELOPE DEPOSITORY UNIT SLIDE TRAY OUT FULLY.
REPLENISH ENVELOPES (ENVELOPE SUPPLY UNIT)
2. FOLLOWING THE INSTRUCTIONS ON INSERTING ENVELOPES (LABEL ON
UNIT
), LOAD ENVELOPES (FLAP UP INTO THE SUPPLY BIN). SLIDE TRAY BACK
INTO
THE CABINET.
3. ACCESS MANAGEMENT FUNCTIONS AND FROM THE MAIN MENU SCREEN
SELECT
DIAGNOSTICS > ENVELOPE DEPOSITORY > ENVELOPE DISPENSE AND
RETRACT TEST.
4. AFTER THE TEST IS COMPLETE, PRESS <2> TO EXIT.
THE TEST DISPENSES AN ENVELOPE AND THEN AUTOMATICALLY RETRACTS IT
INTO
THE DEPOSITORY STORAGE BIN (NORMAL OPERATION).
* NOTE *
REMEMBER TO ALTERNATE EN-
VELOPES APPROXIMATELY EVERY
50 WITH FLAPS UP FACING LEFT-
RIGHT.
9
REPLACE RIBBON CARTRIDGE (ENVELOPE DEPOSITORY UNIT)
THE OPTIONAL DEPOSITORY ACCEPTS AN ENVELOPE, MONITORS ITS PROGRESS THROUGH THE UNIT, STAMPS IT WITH
IDENTIFYING
DATA (UP TO 68 CHARACTERS WITH THE DOT MATRIX PRINTER), AND DEPOSITS THE ENVELOPE IN THE
ENVELOPE
DEPOSIT BIN.
1. REMOVE RIBBON CARTRIDGE FROM THE FOUR (4) PLASTIC TABS THAT HOLD IT.
2. MOUNT THE NEW RIBBON CARTRIDGE INTO THE PRINTER HOLDER AS SHOWN BELOW. ENSURE CARTRIDGE ALIGNS
WITH
THE PLASTIC TABS.
3. CONFIRM THAT THE RIBBON IS POSITIONED BETWEEN THE MASK AND HEAD, THEN TURN THE RIBBON KNOB IN A
“CLOCKWISE” DIRECTION UNTIL TAUT.
10
ELECTRONIC LOCK (LaGard)
ENTERING THE COMBINATION
THE ELECTRONIC LOCK COMBINATION CONSISTS OF SIX (6) DIGITS. IF LOCK IS
PROGRAMMED
FOR DUAL CODE, EACH CODE WILL CONSIST OF SIX (6) DIGITS.
THE PRESET COMBINATION OF THE LOCK SHOULD ALREADY BE SET AT 1-2-3-4-
5-6. AFTER INSTALLATION OF THE UNIT HAS BEEN COMPLETED, PERFORM THE
FOLLOWING
STEPS:
1. ENTER THE PRESET COMBINATION(S) AND CHECK FOR PROPER OPERATION. AFTER EACH KEYPRESS, THE LOCK
WILL
BEEP. AFTER THE FINAL DIGIT HAS BEEN ENTERED, THE LOCK WILL BEEP TWICE AND THE OPEN PERIOD
WILL
BEGIN.
2. WITHIN FOUR (4) SECONDS, TURN THE KEYPAD “CLOCKWISE” TO THE OPEN POSITION.
3. AFTER THE LOCK IS OPENED, THE DOOR MAY BE OPENED.
INVALID CODE ENTRY - LOCK WILL BEEP THREE (3) TIMES.
* NOTE *
FOR DUAL CODE OPERATION, THE SECOND CODE MUST BE ENTERED
WITHIN
TEN (10) SECONDS AFTER THE FIRST CODE WAS ENTERED.
CHANGING THE COMBINATION
* IMPORTANT *
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN!
IF YOUR UNIT IS PROGRAMMED FOR DUAL CODE, EACH CODE MUST BE CHANGED INDEPENDENTLY. FOLLOW
THESE
INSTRUCTIONS FOR EACH CODE CHANGE.
TO CHANGE THE COMBINATION OF THE LOCK, SIMPLY FOLLOW THESE DIRECTIONS.
1. ENTER SIX (6) ZEROS.
2. ENTER THE CURRENT COMBINATION (INITIALLY SET AT 1-2-3-4-5-6).
3. ENTER THE NEW SIX (6) DIGIT COMBINATION TWICE.
- IF A MISTAKE IS MADE, WAIT THIRTY (30) SECONDS AND REPEAT THE FIRST 3 STEPS.
4. TEST LOCK COMBINATION SEVERAL TIMES BEFORE CLOSING THE DOOR. THE COMBINATION IS NOW CHANGED.
VALID CODE ENTRY - DOUBLE SIGNAL AFTER VALID SIX (6) DIGIT CODE IS ENTERED.
INVALID CODE ENTRY - TRIPLE SIGNAL AND OLD CODE IS STILL VALID.
11
ELECTRONIC LOCK (LaGard)
SILENT SIGNAL A LARM
(IF FEATURE IS PROGRAMMED AND OPTIONAL ALARM BOX IS CONNECTED TO AN ALARM SYSTEM)
- ALWAYS PERFORM THIS OPERATION WITH THE DOOR(S) OPEN!
1. ENTER LAST DIGIT OF CODE ONE (1) NUMBER HIGHER OR ONE (1) NUMBER LOWER.
EXAMPLE:CODE: 1-2-3-4-5-6
DURESS: 1-2-3-4-5-5 OR 1-2-3-4-5-7
2. THE LOCK WILL OPEN WITHOUT ANY INDICATION THAT THE DURESS SIGNAL HAS BEEN SENT.
LOCKOUT FEATURE
THE LOCK INCLUDES A WRONG TRY PENALTY LOCKOUT FEATURE THAT PREVENTS ENTRY FROM UNAUTHORIZED
PERSONNEL
. THIS FEATURE PERFORMS AS FOLLOWS:
•ENTRY OF FOUR (4) CONSECUTIVE INVALID COMBINATIONS STARTS A 5-MINUTE DELAY PERIOD.
- LED FLASHES RED AT TEN (10) SECOND INTERVALS.
•AT THE END OF THE DELAY PERIOD, TWO (2) MORE CONSECUTIVE INVALID COMBINATIONS WILL RESTART AN ADDITIONAL
5-MINUTE DELAY. ENTRY WILL NOT RESPOND TO A SINGLE KEYSTROKE DURING DELAY PERIOD.
BATTERY LOW WARNING
REPEATED BEEPING DURING AN OPENING INDICATES THAT THE BATTERY IS LOW AND NEEDS TO BE REPLACED. RECOM-
MEND REPLACEMENT OF BATTERY AT LEAST ONCE ANNUALLY. THE BATTERY BOX IS LOCATED ON THE INSIDE OF THE DOOR.
NOTE: IF THE LOCK WILL NOT OPERATE (I.E. REPEATED BEEPING OR NO BEEPING) WHILE THE DOOR IS CLOSED AND LOCKED, THE
BATTERY
MUST BE ENERGIZED FROM THE TWO EXTERNAL TERMINALS ON THE FRONT OF THE PUSH-BUTTON PANEL.
TO ENERGIZE THE LOCK, CONNECT A 9-VOLT ALKALINE BATTERY ON THE EXTERNAL TERMINAL POINTS. MAINTAIN
CONTACT
, ENTER A VALID COMBINATION, AND TURN THE DIAL CLOCKWISE TO OPEN THE LOCK.
NOTE: YOU MUST MAINTAIN BATTERY CONTACT AT ALL TIMES THROUGHOUT THIS PROCEDURE.
CHANGING THE BATTERY
1. OPEN THE ATM VA U LT DOOR(S). REMOVE THE BATTERY BOX COVER BY PULLING THE FRONT PORTION AWAY FROM
THE
VAULT DOOR.
2. THE CONNECTOR IS EASILY REMOVED BY UNSNAPPING IT FROM THE TWO (2) TERMINAL ON THE TOP OF THE BATTERY.
3. REMOVE THE OLD BATTERY. INSTALL/CONNECT A NEW 9-VOLT ALKALINE BATTERY.
4. PUSH THE BATTERY AND THE LEADS COMPLETELY UP INTO THE BATTERY COMPARTMENT.
5. REINSTALL THE COVER AND TEST THE UNIT SEVERAL TIMES BEFORE CLOSING THE VAULT DOOR.
12
ENVELOPE DEPOSIT BIN
THE SECURE ENVELOPE DEPOSIT BIN STORES DEPOSIT TRANSACTIONS. THE CUSTOMER INSERTS AN ENVELOPE CON-
TAINING CHECKS OR BILLS (NOT COINS), THE DEPOSITORY UNIT ACCEPTS THE ENVELOPE, STAMPS IT, AND DEPOSITS IN
THE
ENVELOPE BIN.
REMOVE:
1. OPEN LOWER (LEFT) REAR CABINET DOOR. PULL THE BIN OUT SLIGHTLY, THEN PLACE ONE HAND UNDERNEATH AS
YOU
SLIDE IT OUT FROM THE GUIDE RAILS.
2. INSERT THE KEY AND TURN IT 90° CLOCKWISE. CLOSE THE COVER (HELD BY A MAGNET). TURN THE KEY BACK TO
SECURE
.
MOUNT:
1. INSERT THE KEY AND TURN IT 90° CLOCKWISE. OPEN THE COVER (HELD BY A MAGNET). TURN KEY BACK TO
REMOVE
.
2. WITH ONE HAND UNDERNEATH BIN, GRASP HANDLE AND SLIDE BACK INTO THE GUIDE RAILS. SLIDE THE BIN
FORWARD
UNTIL IT “CLICKS”.
RECOMMENDATION
THE ENVELOPE DEPOSITORY STAMPS DEPOSITED ENVELOPES WITH IDEN-
TIFYING DATA. THIS DATA IS STAMPED APPROXIMATELY IN THE MIDDLE
OF
THE ENVELOPE AS SHOWN IN THE FIGURE AT RIGHT. IF YOUR ENVE-
LOPES HAVE A LOGO/GRAPHIC THAT IS AT OR NEAR THE CENTER, THIS
DATA
WILL PRINT OVER THIS AND MAY MAKE IDENTIFICATION HARD TO
DETERMINE
. RECOMMEND EITHER MOVING YOUR LOGO UP TO THE COR-
NERS OR USE PLAIN ENVELOPES.
/
