Comelit WIKIT040A User manual

Brand: Comelit

Model: WIKIT040A

Category: Security cameras

Type: User manual

Comelit WIKIT040A is an IP camera kit that allows you to set up a wireless surveillance system in your home or business. The kit includes four IP cameras and a network video recorder (NVR). The cameras are pre-configured to connect to the NVR, so you don't have to worry about setting up a complicated network.

The WIKIT040A system is easy to use. The default user is "admin" and the default password is blank. Once you're logged in, you can use the wizard mode to help you with the basic configuration.

The cameras have a range of up to 50m indoors and up to 250m outdoors, depending on the environment and building materials. If you need to extend the range, you can use extra extendable Wi-Fi antennas.

The WIKIT040A system is easy to use. The default user is "admin" and the default password is blank. Once you're logged in, you can use the wizard mode to help you with the basic configuration.

4 IP INPUTS WI-FI KIT

ART. WIKIT040A

Please read this manual thoroughly before use and keep it for future reference

• The kit is pre-configured, the cameras will automatically connect to the NVR

and will be displayed on the screen

• The default User is admin, the default Password is blank (leave the field empty,

simply click on OK)

• The default IP address is 192.168.1.114 (DHCP function is enabled by default)

• In the Network menu, after clicking on the "Show QR code" button, you can find

the QR code to use in the app Comelit View S (available for iOS and Android)

• Once logged in, the wizard mode start and will assist you in basic configuration

• If there are obstacles between the NVR and camera, adjust the camera position

or the NVR position to avoid it

• Operating distance up to 50m indoor and up to 250m outdoor (in free field),

depending on the environment and building materials of the walls. The walls

(including metal garage gate) absorb Wi-Fi signal. Use extra extendable Wi-Fi

antenna to bring camera's antenna inside the wall

• Keep camera and NVR's antennas parallel to get better signal

• If one or few cameras are out of Wi-Fi range, use standard CAT5e cables to

connect them to the NVR's WAN port.

Statement

The instruction is for guidance only. Detailed information is in accordance with the product.

The instruction may include some technical inaccuracies or typographical error thought it is prepared

with our every effort.

The product or procedures described in the instruction may be changed or updated at any time

without advance notice.

For any doubts or to request documents about latest procedures and complementary notes, please

consult with the after-sales service department.

Precautions

The followings describe information about correct usage and risk prevention as well property loss

prevention to be strictly followed.

Please use the devices in an environment within allowable temperature and humidity.

Check if the power supply works normally before operation.

Do not furiously strike on the product and be careful not to fall it over.

Do not install the product in a place with strong electromagnetic radiation.

Do not place a container or others with liquid on the product or allow liquid flowing into inside the

product.

Do not disassemble the product without authorization.

Front Panel Description

1. Power led

2. HDD led

3. Status led

Rear Panel Description

WAN: 10/100 Mbit/sec., standard Ethernet port DC12V: 12 VDC power supply connector

VGA: VGA video output connector HDMI video output

USB: USB connector

Operating System Description

Turn ON / OFF

Confirm that AC voltage matches with NVR .Ensure that the NVR power outlet connect with a good

middle ground grounding. After switching power, the device started, power led is on. Turn into

system, if the status led flashing, it's normal conditions.

Preview

After device start, preview interface can be seen immediately. In the preview interface you can see

the system date, time, channel name. Click the left mouse button, user can preview the single

channel; click the left mouse button, you can return to a multi-interface monitoring state.

Menu operation instructions

Menu composition

Menu component units as following:

（1）Check box: two kinds of status available, "√" means enabled, "□" means disabled. Click the left

mouse button to choose.

For example: "channel" and "video mode" check box in the video search.

（2）Selection box: select the target content according to the drop-down box options. Click the left

mouse button to select.

For example: "channel" and "code stream" in the encode setup menu

（3）List Box: displays the research information in the list, you can try one option for operation

For example: press the left mouse button.

（4）Edit box: enter the name into edit box

For example: in the setup menu, you could input numbers, letters, punctuation and so on in the

"channel" edit box.

a) move the mouse to edit box, click the left mouse button, then enter keyboard appears, select the

desired input target characters click the left mouse button.

b) after input the information, click 【OK】button or button【ESC】can safe or exit

（5） Button: used to implement a specific function or enter the next setup menu, click the left

mouse button.

ESC MENU

Press the right mouse button to exit the menu mode

Click the right mouse button and return to the previous menu level.

Main Menu Introduction

Press right mouse, it will pop-up the main menu. Main menu consists of the following components:

Split screen: select corresponding preview mode in the menu column.

Shortcut menu: in menu column, there are: Device Manage, System setting, Video playback, Video

backup, Color adjust, PTZ control, Manual record, Volume, Setup Guide, Networking,

Add by Wi-Fi, Exit system. User could enter the corresponding menu preview mode.

Video Playback

Channel：to choose the target channel by clicking the check box

means non-selected.

Record mode：to choose the recode mode by clicking the check box

Search time：input the starting and finishing time into edit box

Search：after setup the above search condition, click "search" to begin the corresponding video file

searching and show the files. Red means time recording, green means MD recording,

yellow means sensor recording.

Playback: chose playback and turn into playback interface. In the search list box, choose the time

bucket according up, down, left, right key or move the mouse. Click left mouse to enter

"video playback" interface

Cancel：back to previous menu

Playback toolbar

Select the playback file or time playback file, it will turn into video playback interface.

Playback toolbar: it will show below the playback interface. Each channel can magnify or narrow by

clicking the left mouse.

Stop play：click to stop the video and turn back to playback interface.

Pause/play: click can pause the playback video, click can continue the playback video.

Fast forward：click can fast-forward the video, also times fast forward the video by click the

button again.

Exit playback：click “ESC” or can exit the playback video; or exit until all file have been played.

Manual Record

In the shortcut menu, click Manual record to enter the setup the manual record interface.

Manual record menu include several parts:

Channel: ☑”means enable; “□”means disable.

All on: enable all the channel.

All off: disable all the channel.

OK: confirm an exit

Cancel: click cancel can exit the manual record interface and back to main menu.

PTZ control

Choose the "PTZ control" from shortcut menu .

PTZ control menu including: direction control; auto pan scan; zoom; focus; Iris; speed.

Video backup

Choose the channel, and record mode; setup the search time, then begin search the file. After

choosing the needed file from list box, click Backup and Ok, wait for process bar until 100% and

show backup success.

Notes

：

USB driver pen must be FAT32 format when backup the file

General setup

Choose the "General setup" and turn into it's setup interface.

Time Setup

：

the real time when preview, click ”Refresh” after setting, make sure saving when it

shows ”the recording will stop once you modify the time” and save the setting.

Auto Logout: the present user will be logged off if there is no operation within 10 minutes, and it

needs login again.

Language

：

there is multiple choices according to users, English and so on.

After setting finished, click "Ok", the information will be saved. Click "Cancel" to exit without saving.

Device manage

Before connecting and set up IPC, please confirm that IPC is already connected to LAN.

Right click on the preview interface, pop-up shortcut interface, click “Device manage".

Match code: add cameras to NVR and configure them to work Wi-Fi

When use the function:

• Add/replace a camera to the system

• Match again the camera to the NVR when they lose connection

You’ll need to delete the camera unreachable channel first, then match again the camera to

a free channel (free channel always shows No Video Source under Status).

How to add the camera:

• Connect the camera to the same NVR switch

• Right click with the mouse to popup the NVR main menu, then click Device Manage. Click

“Refresh” on upper right and wait a moment, you’ll see the camera showed in upper box.

• Select the camera in the upper box, select a free channel in the bottom box, click the

“Match Code” button. Wait for the system to match. Once finish, you should see the camera

video on your monitor

• You can disconnect the camera from the switch and move it anywhere you want. When it

gets power, it will automatically connect to NVR and display the image on the monitor (the

camera must be in the NVR’s Wi-Fi range)

Auto Add: add all cameras detected

Delete: delete the selected connected IPC

Delete All: delete all the connected IPC

Manual Edit: modify the IPC parameters of the selected IPC

After finish setup, click “ Ok” button, it will be saved; click: “Cancel” button, it will be not save

Record Setup

Select “Record setup”.

Channel

：

chose the channels as needed by clicking the inverted triangle

Weekday: chose the day as needed, "ALL" means all days in a week.

Schedule

：

every time slot can set different recording modes in all 4 time slot. "Time" recording with

red color, "Motion" recording with green color, "Sensor" recording with yellow color; “☑" means

enabled, “□” means disabled. The bottom parts has times status display, whole schedule from time

0~24 hours

Copy to

：

select the target channel on the right of "copy to "button, click "copy to" and ''Ok" to set

the current channel setup informations to other target video channel. By clicking the button "Cancel",

the setup informations are non-saved.

Network setup

Select “network setup”.

DHCP

choose to enable to obtain IP address automatically. "☑" means enabled ，"□" means

disabled

Cloud (P2P)

：

after connecting internet , click“☑ Cloud (P2P)” to gain a ID , which can be used in IP

remote monitoring in ESeenet network server

IP address

：

the IP address must be unique and cannot be in conflict with the host or workstation on

the same network segment

Subnet mask

：

subnet for the network segment.

Gateway

：

need to set the gateway address to achieve communication between the different

network segments.

MAC address

：

showing the device's MAC address

Preferred DNS

：

DNS IP address

Web port

：

port number IE browser visit, default port is "80"

PPPOE

Start using

：

“☑ PPPOE” means to start up PPPOE dial-up. “□” means not to start up

Username

：

input the user name of ISP into edit box

Password

：

input the password of ISP into edit box

After the page setup is completed, click '"Ok" to save the changes; click "Cancel ", non-save.

DDNS

Automatic analytical function of dynamic domain name, supported Comelit DNS, etc. To use Comelit

DNS see the last page of this manual.

In the "network setup" menu, click " DDNS "

Start using

：

“☑”means DDNS dynamic domain services start using: “□”means not to start up.

Select the right network server and input user name, password and domain

Wi-Fi setup

Wi-Fi channel: choose the Wi-Fi channel

Region: choose between EU, FCC or MKK

Screen Setup

Select “screen setup”

OSD Alpha

：

OSD menu transparency can be adjusted as needed.

VGA Resolution:

choose the desired resolution

Auto Switch:

user can setup the time of auto switching for preview image, it switch in single screen

or 4 channels screen.

Enable

：

“☑”start using, “□” non-start using

After the page setup is completed, click '"Ok" to save the changes ; click "Cancel ", non-save.

Video detection

Channel:

the option to set the alarm channel selection box

Detection

：

select detection type  motion, video loss

Sensitivity

：

chose the trigger video detection sensitivity

Alarm duration: after chose the trigger video detection, choose the time alarm.

Area edit : setup motion detection area; move by dragging the left of mouse.

Alarm

：

“☑”means start ，“□”means non start 。

Buzzer

：

“☑”means start ，“□”means non start。

E-Mail notice: “☑” means sent E-Mail enabled, “□” means sent E-Mail disabled.

Copy to

：

click "copy to", select the target channels and ''Ok" to set the current channel setup

informations to other target video channel. By clicking the button "Cancel", the setup

informations are non-saved.

PTZ Setup

Select ”PTZ setup”

Channel: choose the right channel, click the select box to choose

Protocol: the selected protocol must be the same with the one of PTZ

Copy to

：

click "copy to", select the target channels and ''Ok" to set the current channel setup

informations to other target video channel. By clicking the button "Cancel", the setup informations

are non-saved.

After the setting, click the button of sure to exit with saving the setting, or click the button Cancel to

exit without saving.

User management

Select "User".

Add user: input a new user name in the edit box and set up the operational authority. Click the "Set

Password" to set the new password or it can be the default password.

Delete user: delete the selected user (except Admin, other user has no the right to set up or delete

other users)

Edit user: modify the selected user (Admin, other users has no right to set up other user

permissions)

Set password: set password of logging in user

After the setting, click "OK" to save and exit, or click "cancel" to exit without saving

HDD setup

Select "HDD setup".

Overwrite: “☑” earliest recording files will be covered when the disk is full, “□"shows not cover.

Format: “☑” stands selected, “□” stands not selected, when click "Format" a confirm interface will

pop up, then click confirm to format, click cancel to return the main interface.

System maintenance

Select "System maintenance".

Auto reboot: setting automatic reboot time, it can set" Saturday to Sunday", "Never" means do not

reboot automatically.

System upgrade

: copy firmware to the root directory of USB drive, insert USB, select the USB

storage device, then click "start" to upgrade. When upgrade is completed, click "Ok" then system

auto reboot.

Note: during upgrade, do not cut off power to protect from device damage

Factory setting

Select "Factory setting".

Select the items which need factory setting, click "Ok" to save and exit or click "Cancel" to exit

without saving.

Notes: after factory setting, all the settings will be the initial one, please use carefully.

HDD info

The listbox shows the HDD status information

System version

Device name, device model, H/W version, S/W version could be checked here.

System log

Choose the log type which need to check from list box, and input the time period in the edit box, then

click "Search", the related log information will showed below, you can turn the page by click

"previous" and "next" or input target page to turn

System logout

In the main menu, click "System logout", popup setting interface

Logout: apply for logging users. After logout, if you want to use the device again, need to login

again

Reboot: it will reboot after "OK".

Shutdown: shutdown the NVR

LAN connection

1. Connect NVR with network, make sure network working fine

2. For local view in computer (LAN), open the browser and enter the NVR IP address and the port (if

different from 80)

Note: Internet Explorer setting. If use it for the first time and the software can't load, then

need to make the following setting: Internet options  Safety-Internet  Custom options 

pick Active X and plugin all for opening, click OK.

3. Input Username and Password (the same NVR username and password)

Note: the default user name is admin, no password

Video monitoring homepage:

Monitoring homepage including: preview window, PTZ control, preview, stream selection, channel

opening, setting, playback, user logout, as below:

WAN connection (Esee service)

1. Connect NVR with network, make sure network working fine

2. For remote view in computer (WAN), go to www.dvrskype.com or www.e-seenet.com

Note: Internet Explorer setting. If use it for the first time and the software can't load, then

need to make the following setting: Internet options  Safety-Internet  Custom options 

pick Active X and plugin all for opening, click OK.

1. Go to www.dvrskype.com or www.e-seenet.com, input Esee ID, user name and password, this

user name and password is same with NVR user name and password

Note: the default user name is admin, no password

Video monitoring homepage:

Monitoring homepage including: preview window, PTZ control, preview, stream selection, channel

opening, setting, playback, user logout, as below:

Connection with app Comelit View S

NOTE: to view images of NVRs from smartphones (iOS or Android OS) please use the app

"Comelit View S" which is freely downloadable from the relative stores (Apple Store and

Google Play Store). The same app for smartphones has to be used for tablet devices.

1. Download and install the app Comelit View S from Apple Store or Google Play Store

2. Type the icon to open the application

3. Type "Trial"

4. Type "+" to add the device

5. Type "Add device by ID"

6. Type the icon to add the device with the QR code showed in the Network menu, after

clicking on the "Show QR code" button

7. In the field "Descriptions" enter the name You want

8. In the field "User Name" enter the username (default: admin)

9. In the field "Password" enter the password (default: blank)

10. On the bar select the number 4

11. Type "Submit" to save the configuration

12. To connect to the device, type on the area highlighted in the image below

13. Type on the OK button on the window that appear

14. Now You can see and manage the camera images

COMELIT DNS SERVICE

For this series of NVR is now available the Comelit DNS service.

To use

proceed as follows:

1 – check the firmware version

of the device. If

necessary, update the firmware

2 – verify that,

on the device, nearby

the

label showing

the model, is present the label with the

univocal code

for the

DNS

service registration. In case

it was not

present, contact Comelit

Technical support

3 – connect to the site http://www.comelitdns.com, sign up

by following the instructions and then

create

a host using

the activation code

above

4 – enter the data (hostname, user and password) in the appropriate

NVR menu

5 – to connect to the

device

registered, enter http://hostname.comelitdns.com:port (if different from

80)

Comelit WIKIT040A User manual

Brand: Comelit

Model: WIKIT040A

Category: Security cameras

Type: User manual

The WIKIT040A system is easy to use. The default user is "admin" and the default password is blank. Once you're logged in, you can use the wizard mode to help you with the basic configuration.

Download PDF

report

Comelit WIKIT040A User manual

Comelit WIKIT040A User manual

Related papers

Other documents