Comelit AHDVR042 Series Quick Manual

Page is loading ...

24

4-8-16 HD/FULL-HD INPUTS H264

STAND-ALONE AHD DIGITAL VIDEO

RECORDER

QUICK GUIDE

ART. AHDVR040x-AHDVR080x-AHDVR160x

ART. AHDVR042x-AHDVR082x-AHDVR162x

Please read this manual thoroughly before use and keep it for future reference

25

Technical Parameters

Model Number AHDVR040x AHDVR080x AHDVR160x

Operating

System

Embedded Linux

Video parameter

Video Input 4 (BNC: 1.0Vp-p,75Ω) 8 (BNC: 1.0Vp-p,75Ω) 16 (BNC: 1.0Vp-p,75Ω)

Compression H.264

Encode

resolution

720p / 960H / D1

Bit rate 512 ~ 4096 Kbps (default: 3072 Kbps)

Record &

Playback

4 ch @ 720p record + 1 ch

@ 720p playback in

real-time

8 ch @ 720p record + 1 ch

@ 720p playback in

real-time

16 ch @ 720p record + 1 ch

@ 720p playback in

real-time

Video interface

Inputs BNC x 4 BNC x 8 BNC x 16

Outputs 1 x VGA, 1 x HDMI

Audio interface

Inputs RCA x 1

Outputs RCA x 1 16

Video management

Record mode Alarm, Auto, Motion Detection, Manual

Backup mode USB, Network

Alarm

Inputs 4

Output 1

HDD

Interface SATA

Communication port

Network RJ45 x 1, 10/100 Mbit/sec. Ethernet

Communication RS485 x 1

USB 2

Others

Power Supply 12 VDC

Power

Consumption

< 15 W (without HDD)

Operating

Temperature

-10°C－＋55°C

Operating

Humidity

10%~90% max NOT condensing

26

Model Number AHDVR042x AHDVR082x AHDVR162x

Operating

System

Embedded Linux

Video parameter

Video Input 4 (BNC: 1.0Vp-p,75Ω) 8 (BNC: 1.0Vp-p,75Ω) 16 (BNC: 1.0Vp-p,75Ω)

Compression H.264

Encode

resolution

1080p / 720p / 960H / D1

Bit rate 512 ~ 4096 Kbps (default: 3072 Kbps)

Video interface

Inputs BNC x 4 BNC x 8 BNC x 16

Outputs 1 x VGA, 1 x HDMI

Audio interface

Inputs RCA x 1

Outputs RCA x 1 RCA x 1

Video management

Record mode Alarm, Auto, Motion Detection, Manual

Backup mode USB, Network

Alarm

Inputs 4

Output 1

HDD

Interface SATA

Communication port

Network RJ45 x 1, 10/100 Mbit/sec. Ethernet

Communication RS485 x 1

USB 2

Others

Power Supply 12 VDC

Power

Consumption

< 15 W (without HDD)

Operating

Temperature

-10°C－＋55°C

Operating

Humidity

10%~90% max NOT condensing

27

HDD Installation

Make sure to install the HDD when you first use it.

Panels Description

1. POWER led 9. PTZ: PTZ key

2. 1 ~ 4: CH1 ~ CH4 Single-Screen keys 10. ESC: Exit key

3. QUAD key 11. MENU: Menu key

4. State led, reserved 12. ▲▼◄►: Direction key

5. HDD led 13. : Confirm key

6. FN Switch 14. IR receiver

7. PLAY: Playback key 15. N.C.

8. REC: Manual recording key

Art. AHDVR040x front panel description

28

1. HDD led 8. REC: Manual recording key

2. State led, reserved 9. PLAY: Playback key

3. 1 ~ 8: CH1 ~ CH8 Single-Screen key 10. ESC: Exit key

4. ▲▼◄►: Direction key 11. MENU: Menu key

5. POWER led 12. : Confirm key

6. IR receiver 13. N.C.

7. QUAD key

Art. AHDVR160x, AHDVR082x and AHDVR162x front panel description

1. HDD led 8. REC: Manual recording key

2. State led, reserved 9. PLAY: Playback key

3. Single-Screen key 10. ESC: Exit key

4. ▲▼◄►: Direction key 11. MENU: Menu key

5. POWER led 12. : Confirm key

6. IR receiver 13. N.C.

4 channels DVR rear Panel

1. VIDEO IN: video input 2. HD OUTPUT: high definition video output

3. AUDIO IN: audio input 4. AUDIO OUT: audio output

5. VGA: VGA video output 6. NET: RJ45 network interface

7. USB interface 8. ALARM: alarm inputs / output

3 8 11

1

2 4

5 6 7 9 10

Art. AHDVR080x and AHDVR042x front panel description

29

9. RS485 10. 12 VDC power supply

11. POWER key

8 channels DVR rear Panel

1. VIDEO IN: video input 2. HD OUTPUT: high definition video output

3. AUDIO IN: audio input 4. AUDIO OUT: audio output

5. VGA: VGA video output 6. NET: RJ45 network interface

7. USB interface 8. ALARM: alarm inputs / output

9. RS485 10. 12 VDC power supply

11. POWER key

16 channels DVR rear Panel

1. VIDEO IN: video input 2. Ground terminal

3. AUDIO IN 1: audio input 1 4. ALARM: alarm inputs / output

5. POWER key 6. HD OUTPUT: high definition video output

7. AUDIO OUT: audio output 8. VGA: VGA video output

9. NET: RJ45 network interface 10. USB interface

11. RS485 12. 12 VDC power supply

13. AUDIO IN 2-16: audio input 2-16

3 8 11

1

2 4 5 6 7 9 10

30

Turn ON / OFF

Confirm that AC voltage accessible matches with DVR. Ensure that the DVR power outlet connect with a good

middle ground grounding. After switching power, the device started, 【POWER】 light is on. Turn into system,

if the panel status light flashing, it's normal conditions.

After device start, preview interface can be seen immediately. In the preview interface you can see the system

date, time, channel name.

Note: Default password is empty, click "enter" can into menu directly.

Main Menu Introduction

Press MENU key or right mouse, it will pop-up the main menu. Main menu consists of the following

components:

Split screen: select the corresponding preview mode.

Shortcut menu: System setup, Video playback, Video backup, Color adjust, Channel mode, PTZ control,

Manual record, Volume, Setup wizard and Exit System.

Channel mode

In the shortcut menu, choose "Channel mode". In this menu you can, using the scroll bar [1], select the mode of

the channels that will be connected to the DVR (AHD cameras, Analog cameras, IP cameras Easy series). To

automatically add IP cameras Easy series, then click the button "Add IP Camera" [2].

31

System setup

In the shortcut menu, choose “system setup” and turn into it's sub menu. It includes: General setup, Channel

setup, Record setup, Network setup, System admin.

General setup

Choose the "General setup" and turn into it's setup interface.

Auto Logout: DVR will log off if there is no operation within 10 minutes, it needs login again.

Key Buzzer

：

Enable: there is sound with the controller or pressing key on front panel; Disable: without sound.

Language

：

There is multiple choice according to users

Standard

：

PAL and NTSC are available.

Choose the "Time setup" and turn into it's setup interface.

Date Format: Y/M/D”、“D/M/Y”、“M/D/Y”

System date

System Time

After setting finished, click "ok", the information will be saved. Click "cancel" to exit without saving.

Record setup

Select “record setup” in system setup.

Channel

：

chose the target channel by clicking the select box

Weekday : chose the correspond day as user's need, "ALL" means record all date.

In the time edit box, user can set different time with different recoding mode . "Time " : in red color , "Motion": in

green color , "Sensor": in yellow color ; “☑" means selected, “□” means invalid. There is times status display

which 0~24 hours for whole schedule.

Copy to

：

select the target channel on the right of "copy to "button ,click "copy to" and ''ok " then system will set

the current channel setup informations to other target video channel. Click button "cancel", the setup

informations is non-saved but to exit.

32

Network setup

Select “network setup” from “system setup” menu.

DHCP：select DHCP to get IP automatically. “☑”means works ；“□” means non-work.

ESee

：

after connecting internet , click“☑ Esee” and save the setting, user will get an Esee ID. You can

remote DVR with this ID by www.dvrskype.com. It's free DDNS, no need to apply the domain name from any

server.

IP address

：

the IP address must be unique and cannot be in conflict with the host or work station which on

the same network segment.

Subnet Mask

：

use for distinguish the network segment.

Gateway

：

need to set the gateway address to achieve communication between the different network

segments.

MAC address

：

device's MAC address

Web port

：

this port number is used for IE browser visit; default port is "80".

Preferred DNS

：

preferred DND IP address.

DDNS: The automatic analytic function of dynamic domain name, it could supported Comelit DNS, etc. To

use Comelit DNS see the last page of this manual.

In the "network setup" menu, click " DDNS " to enter it's setup interface

Enable

：

“☑”means DDNS service start using ;“□”means stop using.

Select the corresponding network server and input user name, password and domain name

Select “PPPOE” from “network setup” menu..

Enable

：

“☑ PPPOE Function” means to start up dial-up by PPPOE protocol, “□” means stop it.

Username

：

input the user name of ISP into edit box

Password

：

input the password of ISP into edit box

After the page setup is completed, click '"OK " to save the changes and exit ; click "cancel ", to exit the setting.

33

Esee User Manual

1. Connect DVR with network, make sure network working fine

2. For remote view in computer, go to www.dvrskype.com

Do the following setup before you log in Esee on computer

Note: Internet Explorer setting. If use it for the first time and the software can't load, then need to make

the following setting: Internet options  Safety-Internet  Custom options  pick Active X and plugin

all for opening, click ok.

4. Go to www.dvrskype.com ,input Esee ID, user name and password, this user name and password is same

with DVR user name and password

Note: the default user name is admin, no password

Remote Video Viewer

After connecting, remote video viewer includes: preview window, PTZ control, preview mode, stream

option, channel on/off, setting, configuration, playback, user logout, as below :

34

Open preview: In preview window, click left mouse, choose target channel, (If channel frame is red, means

select). In channel on/off table, click left mouse, can open or close that channel video, such as:

on; off

Preview mode: In preview mode switch table, can click to choose mode, or double click channel to

signal channel preview mode, or switch to multi-channel mode.

NOTE: to view images of this series of DVRs from smartphones (iOS or Android OS) please use the app

"ESEENET+" which is freely downloadable from the relative stores (Apple Store and Play Store). The

same app for smartphones has to be used for tablet devices.

Page is loading ...

47

Technische specificaties

Model AHDVR040x AHDVR080x AHDVR160x

Besturingssysteem

Embedded Linux

Parameters video

Video-ingangen 4 (BNC: 1.0Vp-p,75Ω) 8 (BNC: 1.0Vp-p,75Ω) 16 (BNC: 1.0Vp-p,75Ω)

Beeldcompressie H.264

Coderingsresolutie 720p / 960H / D1

Bit rate 512 ~ 4096 Kbps (default: 3072 Kbps)

Opnemen / Afspelen

4 ch @ 720p opnem. + 1

ch @ 720p afspelen in

real time

8 ch @ 720p opnem. + 1

ch @ 720p afspelen in

real time

16 ch @ 720p opnem. + 1

ch @ 720p afspelen in real

time

Video interface

Ingangen BNC x 4 BNC x 8 BNC x 16

Uitgangen 1 x VGA, 1 x HDMI

Audio interface

Ingangen RCA x 1

Uitgangen RCA x 1 16

Video management

Opnamemodus Alarm, Automatisch, Bewegingsdetectie, Handmatig

Backup-modus USB, netwerk

Alarm

Ingangen 4

Uitgangen 1

Harde Schijf

Interface SATA

Communicatiepoorten

Netwerk RJ45 x 1, Ethernet 10/100 Mbit/sec.

Communicatie RS485 x 1

USB 2

Ander

Voeding 12 VDC

Verbruik < 15 W (zonder Harde Schijf)

Bedrijfstemperatuur -10°C－＋55°C

Bedrijfsvochtigheid 10%~90% max NIET condenserende

48

Model AHDVR042x AHDVR082x AHDVR162x

Besturingssysteem

Embedded Linux

Parameters video

Video-ingangen 4 (BNC: 1.0Vp-p,75Ω) 8 (BNC: 1.0Vp-p,75Ω) 16 (BNC: 1.0Vp-p,75Ω)

Beeldcompressie H.264

Coderingsresolutie 1080p / 720p / 960H / D1

Bit rate 512 ~ 4096 Kbps (default: 3072 Kbps)

Video interface

Ingangen BNC x 4 BNC x 8 BNC x 16

Uitgangen 1 x VGA, 1 x HDMI

Audio interface

Ingangen RCA x 1

Uitgangen RCA x 1 RCA x 1

Video management

Opnamemodus Alarm, Automatisch, Bewegingsdetectie, Handmatig

Backup-modus USB, netwerk

Alarm

Ingangen 4

Uitgangen 1

Harde Schijf

Interface SATA

Communicatiepoorten

Netwerk RJ45 x 1, Ethernet 10/100 Mbit/sec.

Communicatie RS485 x 1

USB 2

Ander

Voeding 12 VDC

Verbruik < 15 W (zonder Harde Schijf)

Bedrijfstemperatuur -10°C－＋55°C

Bedrijfsvochtigheid 10%~90% max NIET condenserende

Page is loading ...

57

SERVIZIO COMELIT DNS

Per questa serie di DVR è ora disponibile il servizio di DNS proprietario.

Per l’utilizzo procedere come segue:

1 – verificare la versione firmware del dispositivo. Se necessario, procedere all’aggiornamento del firmware

2 – verificare che sul dispositivo, nelle vicinanze dell’etichetta che riporta l’articolo, sia presente l’etichetta con il

codice univoco di registrazione al servizio. In caso non fosse presente, rivolgersi al centro di assistenza di

zona

3 – collegarsi al sito http://www.comelitdns.com , registrarsi seguendo le istruzioni e successivamente creare

un host utilizzando il codice di attivazione di cui sopra

4 – inserire i dati (nome host, utente e password) nell’apposito menu del DVR

5 – per connettersi al dispositivo registrato, digitare http://nomehost.comelitdns.com:porta (se diversa dalla 80)

COMELIT DNS SERVICE

For this

series

of

DVR

is now available

the Comelit

DNS service.

To use

it

proceed as follows:

1 – check the firmware version

of the device. If

necessary, update the firmware

2 – verify that

on the device, nearby

the

label showing

the model, is present the label with the univocal code

for

the

DNS

service registration. In case

it was not

present, contact Comelit

Technical

support

3 – connect to the site http://www.comelitdns.com , sign up

by following the instructions and then create

a

host using

the activation code

above

4 – enter the data (hostname, user and password) in the appropriate

DVR menu

5 – to connect to the

device

registered, enter http://hostname.comelitdns.com:port (if different from

80)

SERVICE COMELIT DNS

Pour cette série de

DVR est maintenant disponible le service

de DNS propriétaire.

Pour l'utilisation procédez comme suit:

1 – vérifiez la version du

firmware

du dispositif. Si

nécessaire, mettre à jour le

firmware

2 – vérifier que sur le

dispositif, en proximité de l'étiquette qui montre

le modèle, est présent l'étiquette avec le

code unique

necessaire pour utiliser le service DNS. Au cas où il

n'était pas présent, contacter le

service

Technique Comelit

3 – connecter au site http://www.comelitdns.com , enregistrer-vous

en suivant les instructions et puis créer un

hôte en utilisant le code d'activation ci-dessus.

4 – entrer les données (nom hôte, utilisateur et mot de passe) dans

le menu

du

DVR

5 – pour se connecter à

l'appareil enregistré, tapez http://nomhôte.comelitdns.com:port (si différente de

80)

Page is loading ...

Comelit AHDVR042 Series Quick Manual

This manual is also suitable for

Comelit AHDVR042 Series Quick Manual

in other languages

Related papers

Other documents