Intratone EEN-TAF Installation guide

Type
Installation guide
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 1 of 14
INSTALLATION AND CONNECTION OF EEN-
TAF NOTICE BOARD
GENERAL POINTS
The digital Notice Board is an electronic device which can replace paper-based publication of
information in apartment-building entrance halls.
Three models are available:
- Two models for interior installation:
o A built-in model which can be fitted within a utility column or a wall-fitting.
o Flush-mount model.
- A surface-mounted model for exterior installation with a built-in temperature control and
connection behind the back-box.
A)
A
3G
M
ODULE
A
N
OTICE
B
OARD
This panel must be connected to a 3G module (with a specific communication channel
dedicated to it). You can, nevertheless, connect it to a "Real-time" central unit from the range.
Please note:
A single panel per 3G Module.
B)
P
ANEL CONFIGURATION
It is mainly configured using the following website: www.intratone.com in the "management
website" tab. Nonetheless, some settings can be changed directly on the Panel using switches
on the panel's electronic board:
- Contrast settings.
- Resetting the Panel.
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 2 of 14
CONTENTS
GENERAL POINTS-----------------------------------------1
A)
A
3G
M
ODULE
A
N
OTICE
B
OARD
-------------------------------------------------1
B)
P
ANEL CONFIGURATION
-------------------------------------------------------------- 1
CONTENTS---------------------------------------------------2
DIMENSIONS AND ASSEMBLY OF THE PANEL -3
A)
"
SURFACE
-
MOUNTED
INTERIOR VERSION
"
:
DIMENSIONS
AND
F
ITTING
--3
B)
«
SURFACE
-
MOUNTED
INTERIOR VERSION
» :
R
EMOVAL OF CABLE CUT
-
OUT
4
C)
"
SURFACE
-
MOUNTED
INTERIOR VERSION
":
D
IMENSIONS
---------------------- 5
D)
"
SURFACE
-
MOUNTED
EXTERIOR VERSION
" :
D
IMENSIONS
--------------------- 6
E)
"
SURFACE
-
MOUNTED
EXTERIOR VERSION
":
D
IMENSIONS OF BRACKET
------7
F)
"
FLUSH
-
MOUNTED
INTERIOR VERSION
" :
C
UT
-
OUT FOR THE WALL PLATE
---8
G)
"
FLUSH
-
MOUNTED
INTERIOR VERSION
":
D
IMENSIONS
-------------------------- 9
H)
"
FLUSH
-
MOUNTED
INTERIOR VERSION
" :
F
ITTING THE WALL PLATE
-------- 10
WIRING ------------------------------------------------------11
A)
G
ENERAL POINTS
-------------------------------------------------------------------- 11
B)
DIFFERENT MODELS
----------------------------------------------------------------- 11
C)
A
S
INGLE POWER SUPPLY
---------------------------------------------------------- 11
D)
D
UAL POWER SUPPLIES
------------------------------------------------------------ 12
EQUIPMENT CONFIGURATION----------------------12
A)
O
N
-
SITE CONFIGURATION OF CONTRAST
:
S
WITCH
N
O
.6 ---------------------- 12
B)
R
ESETTING THE PANEL
------------------------------------------------------------- 13
C)
C
ONFIGURATION USING THE FOLLOWING WEBSITE
:
WWW
.
INTRATONE
.
COM IN
THE
"
MANAGEMENT WEBSITE
"
TAB
.------------------------------------------------------- 13
POST-INSTALLATION CHECK -----------------------13
TROUBLESHOOTING -----------------------------------13
CERTIFICATE OF CONFORMITY--------------------14
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 3 of 14
DIMENSIONS AND ASSEMBLY OF THE PANEL
A)
"
SURFACE
-
MOUNTED
INTERIOR VERSION
"
:
DIMENSIONS
AND
F
ITTING
Slide
the Panelto
close
AND
hold it
against the
wall while
screwing it
on
2 screws for fixing the
panel onto its base
External cable
cut-out
"see OTHER
SIDE"
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 4 of 14
B)
«
SURFACE
-
MOUNTED
INTERIOR VERSION
» :
R
EMOVAL OF CABLE CUT
-
OUTS
1) Unscrew the nuts and plate
2) Fit the protective sleeve
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 5 of 14
C)
"
SURFACE
-
MOUNTED
INTERIOR VERSION
":
D
IMENSIONS
Internal - cable cut-outs
without // with protective
sleeve
Wall-mounting
points
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 6 of 14
D)
"
SURFACE
-
MOUNTED
EXTERIOR VERSION
" :
D
IMENSIONS
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 7 of 14
E)
"
SURFACE
-
MOUNTED
EXTERIOR VERSION
":
D
IMENSIONS OF BRACKET
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 8 of 14
F)
"
FLUSH
-
MOUNTED
INTERIOR VERSION
" :
C
UT
-
OUT FOR THE WALL PLATE
M
OUNTING PLATE ON WHICH THE STUDS ARE FIXED
C
UT
-
OUT
for the
wall-plate:
300 X 224
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 9 of 14
G)
"
FLUSH
-
MOUNTED
INTERIOR VERSION
":
D
IMENSIONS
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 10 of 14
H)
"
FLUSH
-
MOUNTED
INTERIOR VERSION
" :
F
ITTING THE WALL PLATE
3
1
2
NOTE:
MAKE THE
DIMENSIONS
SUFFICIENTLY
GENEROUS TO
MAKE FITTING
EASIER
4
5
6
P
OWER SUPPLY TO THE
CENTRAL UNIT
(12
24
V)
Make the cut-out
Fit the 10 studs onto the mounting plate on the utility column.
Insert the panel onto the studs and hold it against the column
Screw the 10 nuts onto the studs
Wire up the equipment
Final view on the utility column
1
2
3
4
5
6
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 11 of 14
WIRING
A)
G
ENERAL POINTS
Power supply : 24V – 2A (interior versions) or 3A (exterior version)
Twisted-pair wiring
Diameter: 0.8 – Max. length: 100m
Panel connections with a 3G Module: Always use the " Auxiliary data bus "
B)
DIFFERENT MODELS
C)
A
S
INGLE POWER SUPPLY
Terminal Detail NB. pairs
+ / - Power supply 1
1 / 2 Connection Pow. 1
D+ / D- Data 1
Interior surface-mount
model
POWER:
24V
2
OR
3
A
MP
AS CLOSE AS POSSIBLE
TO THE
PANEL
(NOT SUPPLIED)
Interior flush-mount
24V
-
2
A
MP
(NOT SUPPLIED)
E
XTERIOR SURFACE
-
MOUNT
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 12 of 14
D)
D
UAL POWER SUPPLIES
EQUIPMENT CONFIGURATION
A)
O
N
-
SITE CONFIGURATION OF CONTRAST
:
S
WITCH
N
O
.6
Adjustment of the panel's contrast is by means of switch no.6.
There are 4 different levels of contrast.
The factory setting is:
How to proceed:
1. Turn switch no.6 to ON
2. You will see a number between 1 and 4 displayed
indicating the contrast setting.
3. Select the required contrast setting.
4. Turn switch no.6 to OFF.
5. This saves the contrast setting.
Terminal Detail NB pairs
+ / - Power
supply
2
2 Ground 0.5
D+ / D- Package 1
Power supply to central units:
12 or 24V
(NO
T
SUP
Contrast setting
2
POWER:
24V
2
OR
3
A
MP
AS CLOSE AS POSSIBLE TO
THE PANEL
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 13 of 14
B)
R
ESETTING THE PANEL
Resetting the panel returns it to the factory settings.
This is done by means of switches no.5 and 6:
"Follow the instructions displayed on the panel"
How to proceed:
1. Turn switch no.5 to ON then no.6 to ON
2. The panel displays a message: "Follow the instructions".
3. Switch the panel on and off.
4. Waitfor the panel to be fully switched on
5. Turn switch no.5 and 6 to OFF.
6. The panel isreset to its factory settings.
C)
C
ONFIGURATION USING THE FOLLOWING WEBSITE
:
WWW
.
INTRATONE
.
COM IN
THE
"
MANAGEMENT WEBSITE
"
TAB
.
The Notice Board must be configured beforehand on the following website:
www.intratone.com in the "management website" tab before use.
If you have a fleet contract, you will need to declare this equipment using your Intratone
contract number and the telephone number of the 3G Module connected.
POST-INSTALLATION CHECK
Before leaving the installation, the following points should be checked:
Are you sure the power supply is 24V?
Is the contrast correct?
Check that the power supply is of the correct amperage
TROUBLESHOOTING
What is the fault? What is causing the
fault?
How to fix the fault?
The panel does not turn on - Power is not 24V
- + / - wiring
- See Power recommendation
- Check + / - wiring
Even after update: "No
display"
- Switch positions
- D+ / D- wiring
- Switch 1 to 4 to ON
- Check D+ / D- wiring
No display
EN-V231-5006 - AA - Installation and Connection of the EEN-TAF Notice Board
Page 14 of 14
CERTIFICATE OF CONFORMITY
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14

Intratone EEN-TAF Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI