MicroNet SP6148WS Quick Installation Guide

Brand: MicroNet

Model: SP6148WS

Type: Quick Installation Guide

P/N: 2300-0485

Quick Installation Guide

48-Port Gigabit Web Smart Switch

Model No.: SP6148WS

http://www.micronet.com.tw ; www.micronet.info

Specifications

Step 3. Select 'Use the following IP Address' button and then

enter the IP address and subnet mask. Ensure the IP address

and subnet mask are on the same subnet as the switch. Click

on 'OK' button to save the setting.

Default Values

IP Address

Subnet Mask

Default Gateway

Password

192.168.1.1

255.255.255.0

192.168.1.254

admin

Web-based User Interface

SP6148WS is embedded with http sever and provides a series

of web pages, which display the configuration and status of the

system. After configuration of IP, the management interface

can be access by entering the IP address of the switch into the

browser.

On the left hand side of the browser will

contain a menu tree with list of functions.

Menu is in hierarchical structure and opening

the menu will display a sub-menu.

For detail information of

each function, refer to the

user manual.

Standards

Buffer Memory

Mac Address Table

Interface

Bridging

QoS

Security

IEEE802.3 / 802.3u / 802.3ab

/ 802.3z / 802.3x

768 KB on-chip frame buffer

8K entries

• 44 x Port 10/100/1000Mbps TP

• 4 x Port Gigabit TP/SFP Fiber

• Tag-based VLAN (802.1Q)

• Port-based VLAN

• Port Mirror, Port Sniffer

• Port Trunk

• Jumbo frame (16k bytes)

• QOS modes (DSCP, 802.1p and port

priority)•

• Scheduling (Weighted Round Robin)

• Multicast and broadcast storm control

• 4 shaper queues

• ACL QoS load

• ACL rules for traffic classification and

prioritize•

• VLAN for isolation of traffic between

users•

Management

SNMP & MIBs

SNMP, All MIB OIDs, RMON MIB

Data Transfer Rate

Switch Fabric

Filtering /

Forwarding Rate

Emission

Environment

Dimension

Power Supply

Web-based, Telnet, Console

10M(Half duplex)/20M(Full duplex)

100M(Half duplex)/200M(Full duplex)

1000M(Full duplex)

48 Gbps

10Mbps: 14,880pps

100Mbps: 148,800pps

1000Mbps: 1,488,000pps

o o

Operating Temperature: 0 - 40 C

Operating Humidity: 5% - 90%

442 x 248.6 x 44 mm

100-240V AC, 50-60Hz

AC:100-240V~

50/60 Hz, 3.0A Max

MADE IN TAIWAN

SERIAL

13 15

29 31

2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48

45 47

SFP

CPU

PWR

RESET

SP6148WS 48-Port Gigabit Web Smart Switch

SFP

1 2

Introduction

Micronet SP6148WS 48-port Gigabit Web Smart Switch

delivers truly non-blocking and wire-speed Gigabit performance

for enterprises and service providers that demand high-port

density applications. Moreover, it brings advanced features, as

tag-based VLAN, port trunk, L2/L3/L4 traffic prioritization,

bandwidth control, and ACL, to optimize the network.

Key Features

Prior to the installation of the device, please verify the following

items are in the package:

SP6148WS Gigabit Web Smart Switch

Quick Installation Guide

Manual CD

Mounting Accessory (for 19" Rack Shelf)

AC Power Cord

•

Package Contents

•

IEEE802.3 10Base-T, IEEE802.3u 100Base-TX, IEEE802.3ab

1000Base-T, and IEEE802.3z 1000Base-LX/SX standards.

48 x 10/100/1000M RJ-45 ports and 4 x shared SFP slots

48Gbps non-blocking switching capability

Wire-speed performance at jumbo packet size of 16K bytes

Head of Line (HOL) blocking prevention

IEEE802.1q tag-based VLAN, 256 VLAN groups

Traffic optimization using various class of service option: per-

port, L2 priority (802.1p), L3 priority (TOS or DSCP), L4

priority (TCP/UDP service number), and IPv6 traffic class

4 hardware priority queues

Enhanced traffic rule and security by L2/L3/L4 ACL (Access

Control List)

Broadcast and multicast storm control

Ingress and egress per port bandwidth control

Port trunk with flexible load distribution and failover function

SNMP trap, E-mail, and SMS alarm for any connectivity

events

•

Installation

SP6148WS can be mounted in a 19-inch rack, which can be

placed in a wiring closet with other equipment. The switch

provides 44 Port 10/100/1000Mbps TP and 4 Port Gigabit

TP/SFP Fiber. Follow the steps below to configure and set up

the gigabit switch.

IP Address Configuration

PC/Notebook must belong in the same IP range and subnet.

Follow the steps below to configure IP settings for LAN PC.

Physical Description

SP6148WS front view

SP6148WS rear view

RESET Button:

The button is used to reboot the equipment.

LED definition

LED Status Operation

System LED

POWER

Switch is working properly

CPU fails or initializes

10/100/1000Ethernet TP Port (1 to 48 port)

Link with remote device is good

Traffic is present

Link is off or bad connection

1000M link is detected

100M link is detected

10M or no link is detected

1000SX/LX Gigabit Fiber Port (44 - 48 port)

Link with remote device is good

Traffic is present

Link is off or bad connection

Power is on

On/Green

CPU Blink/Green

Off

LINK/ACT

On/Green

Blink/Green

Off

10/100/

1000M

On/Green

Blink/Green

Off

SFP

(LINK/ACT)

On/Green

Blink/Green

Off

Step 1. In the control panel,

double click on Network

Connections. Double click on

the local area connection

(e.g. LAN). The following

screen will appear.

Step 2. Select 'Internet

Protocol (TCP/IP)', and then

click on the 'Properties'

button. The screen will

appear to allow entry of

TCP/IP settings.

MicroNet SP6148WS Quick Installation Guide

MicroNet SP6148WS Quick Installation Guide

MicroNet SP6148WS Quick Installation Guide

Related papers

Other documents