Toro Baffle Kit, 72in Rear Discharge Z Master Mowers Installation guide
- Category
- Lawnmowers
- Type
- Installation guide
This manual is also suitable for
Toro Baffle Kit, 72in Rear Discharge Z Master Mowers is a reliable tool that will enhance the capabilities of your mower, allowing you to work more efficiently and achieve a professional-looking finish on your lawn. With the ability to convert your mower to a rear discharge configuration, you'll gain greater control over the direction of grass clippings, making it easier to achieve an even cut and reduce the amount of time spent cleaning up.
Toro Baffle Kit, 72in Rear Discharge Z Master Mowers is a reliable tool that will enhance the capabilities of your mower, allowing you to work more efficiently and achieve a professional-looking finish on your lawn. With the ability to convert your mower to a rear discharge configuration, you'll gain greater control over the direction of grass clippings, making it easier to achieve an even cut and reduce the amount of time spent cleaning up.
FormNo.3381-168RevB
BafeKit
60inor72inRearDischargeZMaster
®
Mowers
ModelNo.125-9305
ModelNo.125-9310
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
1
RemovingtheOriginal
Hardware
NoPartsRequired
Procedure
1.Ensurethatallmovingpartshavestopped,theparking
brakeisengaged,andthekeyhasbeenremoved.
2.Raisethefrontofthemachineandsupportitwithjack
stands.
WARNING
Raisingthemowerdeckforserviceor
maintenancerelyingsolelyonmechanical
orhydraulicjackscouldbedangerous.The
mechanicalorhydraulicjacksmaynotbe
enoughsupportormaymalfunction,allowing
theunittofall,whichcouldcauseinjury.
Donotrelysolelyonmechanicalorhydraulic
jacksforsupport.Useadequatejackstands
orequivalentsupport.
Important:Theright-handbladeonthismower
deckiscounter-rotatingandusesaleft-hand
threadedbladebolt.
3.Removethebladesandretainthemforremovalofthe
bafekit.
4.Ifthemowerhasbeenused,scrapetheundersideof
themowerdeckclean.
5.Removethehardwarethatplugstheexposedmounting
holesinthedeck.
•For60-inchdecks,removethe6hex-socketscrews
(5/16-18x3/4inch)andangednylocnuts
pluggingtheexposedmountingholesinthedeck
(
Figure1).
Note:Retainthesepartsforfutureuse.
Figure1
60-inchdeckshown
1.Partsthatneedtoberetained
•For72-inchdecks,removethe4hex-socketscrews
(5/16-18x3/4inch),theangednutsplugging
theexposedmountingholesinthedeck,andthe
inboard-tire-apfasteneroneachside(
Figure2).
Note:Retainthesepartsforfutureuse.
©2014—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.
OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved
*3381-168*B
Figure2
72-inchdeckshown
1.Socketscrew2.Carriagebolt
6.Removeandretainthe2rearcarriagebolts(3/8-16x
2-1/4inches)andangenutsfromeachsidewithin
thecuttingchamberthatattachthesidebumpersto
thedecksides.
2
InstallingtheBafes
Partsneededforthisprocedure:
1
Frontright-handbafe
1
Rearright-handbafe
1
Frontcenterbafe
1
Rearcenterbafe
1
Frontleft-handbafe
1
Rearleft-handbafe
1
Right-handkickerbafe
1
Centerkickerbafe
1
Left-handkickerbafe
2
Locknut(3/8-16)
14
Carriagebolt(3/8-16x7/8inch)—60-inchmodelonly
12
Carriagebolt(3/8-16x7/8inch)—72-inchmodelonly
16
Flangenut(3/8-16)—60-inchmodelonly
10
Flangenut(3/8-16)—72-inchmodelonly
2
Carriagebolt(5/16-18x1inch)—72-inchmodelonly
2
Flangenut(5/16-18)—72-inchmodelonly
Procedure
Note:Determinetheleftandrightsidesofthemachine
fromthenormaloperatingposition.
2
Figure3
1.Frontright-handbafe8.Left-handkickerbafe
2.Carriagebolt9.Rearleft-handbafe
3.Flangenut10.Locknut
4.Centerkickerbafe11.Rearcenterbafe
5.Frontcenterbafe12.Rearright-handbafe
6.Frontleft-handbafe13.Right-handkickerbafe
7.Carriagebolt(5/16-18x1inch)andangenut
(5/16-18)—72-inchmodelonly
1.Installthefrontouterbafesbyusingonecarriage
bolt(3/8-16x7/8inch)andoneangenut(3/8-16)
perbafe(Figure3).
Note:Tohelpalignthebafes,looselyinsertthe
carriagebolts(3/8-16x2.5inches)andangenuts
(3/8-16)throughthesideofthebafesandthebumper
(Figure6).
2.Installthefrontcenterbafewith3carriagebolts
(3/8-16x7/8inch)andangenuts(3/8-16)asshown
inFigure3.
3.Installtherearouterbafesbyusingonecarriagebolt
(3/8-16x7/8inch)andoneangenut(3/8-16)per
bafeasshownin
Figure3.
Note:Tohelpalignthebafes,looselyinsertthe
carriagebolts(3/8-16x2.5inches)andangenuts
(3/8-16)throughthesideofthebafesandthebumper
(Figure6).
Note:Thefrontouterbafesinstallbetweenthe
rear-bafetabs.
Note:The72-inchmodelusesonecarriagebolt
(5/16-18x1inch)andoneangenut(5/16-18)inthe
rearoftheright-handbafe,theleft-handbafe,and
theinnermostsquareholeontheinboardtireapon
eachside(
Figure3).
4.Installtherearcenterbafeusing2carriagebolts
(3/8-16x7/8inch)and2locknuts(3/8-16)asshown
inFigure4.
Note:Thisbafeinstallsbetweenthefrontouter
bafeanges(Figure4).
Note:Wherethefrontouterbafes,therearouter
bafes,andtherearcenterbafecometogether,install
2carriagebolts(3/8-16x7/8inch)andthe2locknuts
(3/8-16)asshowninFigure4.
3
Figure4
1.Carriagebolt(3/8-16x7/8
inch)
3.Frontbafeange
2.Rearcenterbafe4.Locknut(3/8-16)
5.Tightenallofthehardware.
6.Usingonecarriagebolt(3/8-16x7/8inch)andone
angenut(3/8-16),installthecorrectkickerbafeto
eachchamber(Figure1).
Note:Thehookedendofeachkickerbafeattaches
totheslotinthechamberbafe(Figure5).
Note:Youmayneedtoloosenthematingbafeto
allowthehookedendofthekickerbafetotcorrectly.
Figure5
1.Slot
2.Hookedend
3
SecuringtheBumpersandthe
RightandLeft-handBafeto
theMowerDeck
Partsneededforthisprocedure:
4
Carriagebolt(3/8-16x2.5inches)
4
Flangenut(3/8-16)
Procedure
Note:Youmayneedtoloosenthematingbafeandkicker
bafetoallowthebumperboltstobeinstalled.
1.Insert2carriagebolts(3/8-16x2.5inches)oneach
sidethroughtherightandleft-handbafeandthe
bumpers(Figure6).
Figure6
1.Flangenut(3/8-16)4.Left-handbafe
2.Bumper
5.Right-handbafe
3.Carriagebolt(3/8-16x2.5
inches)
2.Securethecarriageboltswith2angenuts(3/8-16)on
eachside(Figure6).
3.Torquethecarriageboltsandangenutsto12.4to
14.7N-m(110to130in-lb).
4
4
InstallingtheBlades
Partsneededforthisprocedure:
1
20.5-inchrotaryblade(red)—60-inchmodelonly
2
20.5-inchlow-owblade(black)—60-inchmodelonly
1
24.5-inchrotaryblade(red)—72-inchmodelonly
2
24.5-inchlow-owblade(black)—72-inchmodelonly
Procedure
Note:Determinetheleftandrightsidesofthemachine
fromthenormaloperatingposition.
Important:Theright-handbladeonthismowerdeck
iscounter-rotatingandusesaleft-handthreadedblade
bolt.
1.Installtheredreverse-rotationbladeontothe
right-handspindle(Figure7).
Note:Ensurethatthecurvedpartofthebladeis
pointingupwardtowardtheinsideofthemowerdeck
toensurepropercutting.
Note:Ensurethatthecurved-washerconeisinstalled
towardsthebolthead(
Figure8).
Figure7
1.Centerspindle4.Centerblade(black)
2.Left-handspindle
5.Right-handspindle
3.Left-handblade(black)6.Right-handblade(red)
Figure8
Leftandcenterspindleshown
1.Sailareaoftheblade3.Curvedwasher
2.Blade4.Bladebolt
2.Installthe2blackbladesontothecenterandleft-hand
spindle(Figure7).
3.Torquethebladeboltsto115to150N-m(85to110
ft-lb).
Note:Carefullyandslowlyrotateeachblade360°
byhandtoensurethatthereisclearancebetweenthe
bladesandthebafes.Adjustthebafesslightlyif
interferenceisfound.
WARNING
Incorrectinstallationofthebladesor
componentsusedtoretainthebladescanbe
dangerous.Failuretousealloftheoriginal
componentsandensuringthateverythingis
assembledasshowncouldallowabladeora
bladecomponenttobethrownoutfromunder
thedeck,resultinginseriouspersonalinjury
ordeath.
Alwaysinstallthebladesandthe
blade-retaininghardware;refertothe
Operator’ s Man ual
.
4.Carefullyremovethejackstandsandlowerthemachine
totheground.
5
5
ConvertingBacktoRear
Discharge
NoPartsRequired
Procedure
1.Stopengineandwaitforallmovingpartstostop,
engagetheparkingbrake,removethekey,and
disconnectthenegativebatterycable.
2.Removethenish-cutbafesandthekickerbafes,
andretainallofthehardware.
3.Replacethenish-cutbladeswithstandardblades.
4.Installthe5/16-18x3/4-inchhex-socketscrewsand
theangenutsintheholesontopofthedeckwith
theboltheadunderneath.
Note:Allopenholesnotcoveredbybeltshieldsorthe
framemustbepluggedtopreventsandand/orother
smallobjectsfrombeingthrownupthroughthedeck.
6
Notes:
7
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Toro Baffle Kit, 72in Rear Discharge Z Master Mowers Installation guide
- Category
- Lawnmowers
- Type
- Installation guide
- This manual is also suitable for
Toro Baffle Kit, 72in Rear Discharge Z Master Mowers is a reliable tool that will enhance the capabilities of your mower, allowing you to work more efficiently and achieve a professional-looking finish on your lawn. With the ability to convert your mower to a rear discharge configuration, you'll gain greater control over the direction of grass clippings, making it easier to achieve an even cut and reduce the amount of time spent cleaning up.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Toro Baffle Kit, 60in Rear Discharge Z Master Mowers Installation guide
-
-
-
-
-
-
Toro Recycler Kit, 52in TURBO FORCE Side Discharge Mower Installation guide
-
-
-