Toro Baffle Kit, 60in Rear Discharge Z Master Mowers Installation guide
- Category
- Car kits
- Type
- Installation guide
FormNo.3438-977RevA
BafeKit
60inRearDischargeZMaster
®
Mowers
ModelNo.144-0379
InstallationInstructions
Important:Thiskitdoesnotcomewiththerecyclerblades.
1
PreparingtheMachine
NoPartsRequired
Procedure
1.DisengagethePTO,movethemotion-control
leverstotheNEUTRAL-LOCKposition,and
engagetheparkingbrake.
2.Shutofftheengine,removethekey,andwait
forallmovingpartstostopbeforeleavingthe
operatingposition.
3.Raisethefrontofthemachineandsupportit
withjackstands.
WARNING
Raisingthemowerdeckforservice
ormaintenancerelyingsolelyon
mechanicalorhydraulicjackscouldbe
dangerous.Themechanicalorhydraulic
jacksmaynotbeenoughsupportormay
malfunction,allowingtheunittofall,
whichcouldcauseinjury.
Donotrelysolelyonmechanical
orhydraulicjacksforsupport.Use
adequatejackstandsorequivalent
support.
4.Repairallbentordamagedareasofmower
deckandreplaceanymissingparts.
5.Cleanthemachineofanydebrisonthedeckto
easeinstallation.
6.Removetheexistingblades;refertothe
Operator’sManual.
7.Removethe6hex-socketscrews(5/16x3/4
inch)and6angenuts(5/16inch)pluggingthe
exposedmountingholesinthedeck(Figure1).
Note:Retainthesepartsforfutureuse.
g024524
Figure1
1.Retaintheseparts.
8.Removeandretainthe2rearcarriagebolts(3/8
x2-1/4inches)and2angenuts(3/8inch)from
eachsidewithinthecuttingchambersecuring
thesidebumperstothedecksides.
©2020—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3438-977*A
2
InstallingtheBafes
Partsneededforthisprocedure:
1
Front,rightbafe
1
Rear,rightbafe
1
Front,centerbafe
1
Rear,centerbafe
1
Front,leftbafe
1
Rear,leftbafe
1
Rightkickerbafe
1
Centerkickerbafe
1
Leftkickerbafe
2
Locknut(3/8inch)
14
Carriagebolt(3/8x7/8inch)
16
Flangenut(3/8inch)
Procedure
Note:Determinetheleftandrightsidesofthe
machinefromthenormaloperatingposition.
2
g024570
Figure2
1.Front,rightbafe
8.Leftkickerbafe
2.Carriagebolt9.Rear,leftbafe
3.Flangenut
10.Locknut
4.Centerkickerbafe11.Rear,centerbafe
5.Front,centerbafe12.Rear,rightbafe
6.Front,leftbafe13.Rightkickerbafe
7.Carriagebolt(5/16x1inch)andangenut(5/16
inch)—72-inchmodelonly
1.Installthefront,outerbafesusing1carriage
bolt(3/8x7/8inch)and1angenut(3/8inch)
perbafe(Figure2).
Note:Tohelpalignthebafes,looselyinsert
thecarriagebolts(3/8x2-1/2inches)andange
nuts(3/8inch)throughthesideofthebafes
andbumper(Figure5).
2.Installthefront,centerbafeusing3carriage
bolts(3/8x7/8inch)and3angenuts(3/8inch)
asshowninFigure2.
3.Installtherear,outerbafesusing1carriage
bolt(3/8x7/8inch)and1angenut(3/8inch)
perbafeFigure2.
Note:Tohelpalignthebafes,looselyinsert
thecarriagebolts(3/8x2-1/2inches)andange
nuts(3/8inch)throughthesideofthebafes
andbumper(Figure5).
Note:Thefront,outerbafesinstallbetween
therearbafetabs.
3
4.Installtherear,centerbafeusing2carriage
bolts(3/8x7/8inch)and2locknuts(3/8inch)
asshowninFigure3.
Note:Thisbafeinstallsbetweenthefront,
outerbafeanges(Figure3).
Note:Wherethefront,outerbafes,therear,
outerbafes,andtherear,centerbafecome
together,install2carriagebolts(3/8x7/8inch)
and2locknuts(3/8inch)asshowninFigure3.
g021731
Figure3
1.Carriagebolt(3/8x7/8
inch)
3.Frontbafeange
2.Rear,centerbafe4.Locknut(3/8inch)
5.Tightenallthehardware.
6.Installthecorrectkickerbafetoeachchamber
using1carriagebolt(3/8x7/8inch)and1ange
nut(3/8inch)asshowninFigure1.
Note:Thehookedendofeachkickerbafe
attachestotheslotinthechamberbafe(Figure
4).
Note:Youmayneedtoloosenthematingbafe
toallowthehookedendofthekickerbafeto
tcorrectly.
g021732
Figure4
1.Slot
2.Hookedend
4
3
SecuringtheBumpersand
RightandLeftBafetothe
MowerDeck
Partsneededforthisprocedure:
4
Carriagebolt(3/8x2-1/2inches)
4
Flangenut(3/8inch)
Procedure
Note:T oinstallthebumperbolts,youmayneedto
loosenthematingbafeandkickerbafe.
1.Insert2carriagebolts(3/8x2-1/2inches)on
eachsidethroughtherightandleftbafeand
bumpers(Figure5).
g024518
Figure5
1.Flangenut(3/8inch)4.Leftbafe
2.Bumper
5.Rightbafe
3.Carriagebolt(3/8x2-1/2
inches)
2.Securethe2carriageboltsusing2angenuts
(3/8inch)oneachside(Figure5).
3.Torquethecarriageboltsandangenutsto12.4
to14.7N∙m(110to130in-lb).
4
ConvertingBacktoRear
Discharge
NoPartsRequired
Procedure
1.DisengagethePTO,movethemotion-control
leverstotheNEUTRAL-LOCKposition,and
engagetheparkingbrake.
2.Shutofftheengine,removethekey,andwait
forallmovingpartstostopbeforeleavingthe
operatingposition.
3.Removethenish-cutbafesandkickerbafes.
Retainallthehardware.
4.Replacethenish-cutbladeswithstandard
blades.
5.Installthehex-socketscrews(5/16x3/4inch)
andtheangenuts(5/16inch)intheholes
onthetopofthedeckwiththebolthead
underneath.
Note:Youmustplugallopenholesnotcovered
bybeltshieldsortheframetopreventsand
and/orothersmallobjectsfrombeingthrownup
throughthedeck.
5
Notes:
Notes:
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Toro Baffle Kit, 60in Rear Discharge Z Master Mowers Installation guide
- Category
- Car kits
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Toro Baffle Kit, 60in Rear Discharge Z Master Mowers Installation guide
-
Toro Mulching Kit, GrandStand Mower With 122cm Rear Discharge TURBO FORCE Cutting Unit Installation guide
-
Toro Recycler Kit, 52in TURBO FORCE Side Discharge Mower Installation guide
-
-
-
-
-
-
-