TFA Professional Thermo-Hygrometer with Data Logger Function KLIMALOGG PRO User manual

Brand: TFA

Model: Professional Thermo-Hygrometer with Data Logger Function KLIMALOGG PRO

Type: User manual

TFA

KlimaLogg Pro

User Manual

Revision: 1.1

Table of Contents

Overview ............................................................................................................................... 2

Getting Started ...................................................................................................................... 2

Setting up the KlimaLogg Pro device ................................................................................. 2

Installing the USB-Stick ..................................................................................................... 2

Installation ............................................................................................................................. 2

System Requirements ........................................................................................................ 2

Downloading the software .................................................................................................. 2

Installing the software ........................................................................................................ 2

Synchronizing ........................................................................................................................ 5

What is Synchronizing? ..................................................................................................... 5

Requirements .................................................................................................................... 5

Performing the Synchronization ......................................................................................... 5

Operation .............................................................................................................................. 7

Establishing Communication .............................................................................................. 7

Main Window ..................................................................................................................... 7

Overview ........................................................................................................................ 8

Chart .............................................................................................................................. 8

Sensors .......................................................................................................................... 8

Main Menu ......................................................................................................................... 9

Toolbar .............................................................................................................................10

Options .............................................................................................................................10

Logger Settings .................................................................................................................11

Export Data .......................................................................................................................12

Active Channels ................................................................................................................13

Sensor Settings ................................................................................................................13

Charts ..................................................................................................................................15

Overview

Welcome to the KlimaLogg Pro software, the application used to administer your TFA

KlimaLogg Pro device.

Using the KlimaLogg Pro software the data measured by the sensors of your KlimaLogg Pro

device can be transferred and stored on your PC.

The following pages detail the features and usage of the KlimaLogg Pro software application.

Getting Started

Setting up the KlimaLogg Pro device

Before installing the KlimaLogg Pro software on your PC you should complete the setup of

your KlimaLogg Pro device. For further information regarding your KlimaLogg Pro device

please refer to the KlimaLogg Pro device documentation.

Installing the USB-Stick

Before installing the KlimaLogg Pro software on your PC you should complete the setup of

the USB-Stick which is used for wireless communication with your KlimaLogg Pro device. To

install the USB-Stick, plug it into any available USB port on the PC where you want to install

the KlimaLogg Pro software.

Although the USB communication device can be installed on any USB port connected to your

computer, using a non-powered USB hub or extension cable increases the risk for

communication interruptions between the USB communication device and your computer.

Where obstructions are an issue, a good quality USB extension cable can be used if it is

directly connected to either a powered hub or a port on the computer itself.

Installation

System Requirements

The minimum requirements for your PC are as follows:

Supported Operating Systems:

 Windows XP (SP3 or greater)

 Windows Vista (SP1 or greater)

 Windows 7

 min. 1GB main memory

 Suggested display resolution 1024x768 pixels.

Downloading the software

The latest version of the KlimaLogg Pro software can be downloaded at www.tfa-

dostmann.de.

Installing the software

At this point you should have met the following requirements:

 The KlimaLogg Pro device receives data from the internal and external sensors.

 The PC meets the minimum system requirements.

 The KlimaLogg Pro software has been downloaded or otherwise acquired and

transferred to the PC.

Open the KlimaLogg Pro setup file, which you have downloaded. Double click the file to start

the installation. Once the dialog below appears, please click „OK“.

Please click “Next” when the welcome dialog is shown.

Please click “Next” again to accept the default location for installation.

Please click “Next” again to accept the start menu folder where the program shortcuts will be

created.

Finally click “Install” to start the installation process:

During the installation a progress dialog is shown:

When the “Completing” dialog is displayed the installation of the KlimaLogg Pro software is

finished.

Click “Finish” to complete the installation and to start the KlimaLogg Pro Software. Setup

added shortcuts to your start menu and desktop from which you can start the application at

any time.

Synchronizing

What is Synchronizing?

Synchronizing is the process of telling the KlimaLogg Pro device and the KlimaLogg Pro

software how to talk to each other. Usually the synchronize process needs to be done only

once. Software and device are linked to each other during this process through the

exchange of their ID numbers. If device and software somehow loose contact, they will find

each other again through these IDs. Additionally other devices will be ignored so that multiple

devices can work without interfering with each other.

Requirements

Before synchronizing all components should be ready to go:

 The KlimaLogg Pro device is set up and receiving data from the connected sensors.

 The USB stick is connected to the PC.

 The KlimaLogg Pro software is installed.

 The KlimaLogg Pro device is within the transmission range (10m in a free area) of the

USB transceiver. If necessary place the devices side by side.

Performing the Synchronization

If no device has been synchronized, after startup, the KlimaLogg Pro Software shows

automatically the synchronize dialog:

The synchronization can be started manually at any time by choosing “Logger / Synchronize”

from the main menu. You may want to synchronize manually to synchronize additional

devices, the KlimaLogg Pro device and USB stick have lost contact or if the installation has

been finished without successfully synchronizing device and PC.

Using the KlimaLogg Pro software you can use up to 10 KlimaLogg Pro devices at the same

time. Use the logger channel selection to configure the channel that will be used for

synchronization. If you want to resynchronize an already synchronized device please choose

the channel on which the device has been synchronized previously.

If the synchronize dialog is shown and you have selected the channel that should be used for

synchronization you can bring the KlimaLogg Pro device into synchronization mode.

DON’T CLICK THE SYNCHRONIZE BUTTON YET!

Please press the USB key on the KlimaLogg Pro device until it beeps (approximately 3-4

seconds). Next click the synchronize button in the KlimaLogg Pro software (der synchronize

message box should still be shown on the PC) and the KlimaLogg Pro device will attempt to

synchronize to your PC. The process should be finished within the next one or two minutes.

The device will beep if the synchronize process has been successful. The dialog will be close

automatically to show the overview tab in the main window.

You may have to try the synchronization process more than once.

If the synchronization process is not successful, you will see a message similiar to the one

below. At this point, you need to retry the synchronization.

To repeat the synchronization process, please put both the KlimaLogg Pro device and the

KlimaLogg Pro software into synch mode again. To do this please press the USB button on

the device until it beeps, then click the synchronize button in the “Synchronize” dialog.

Operation

This section covers the operation of the KlimaLogg Pro software.

In this document we will not address the operation of your KlimaLogg Pro device, except

where it pertains to the KlimaLogg Pro software. For more information regarding the

operation of the KlimaLogg Pro device, please refer to the device documentation.

Establishing Communication

For communication the KlimaLogg Pro device must be brought into communication mode

and the KlimaLogg Pro software needs to be started. After successful synchronization the

communication between software and device has been established automatically. To

reestablish communication please press the USB key on the device. When the KlimaLogg

Pro device is in communication mode the display of the device will show “USB“.

If the device is searching for the DCF signal or has lost its external sensors, the

communication between PC and device will be interrupted briefly. After the search the

communication will resume automatically.

Main Window

The main window of the KlimaLogg Pro software contains the main menu, the toolbar, the

main area and the status bar. The main area is divided into several tabs.

Overview

The tab “Overview” shows all recorded data of all sensors of a KlimaLogg Pro device. New

datasets are appended at the end of the list.

Chart

The tab “Chart” provides tools to create customizable graphs of the recorded data for

analysis. The section Charts this manual describes this tab in detail.

Sensors

The sensor tabs show all information available for the selected sensor. On the left hand side

the recorded data is displayed. On the right hand side the alarm settings, min./ max. values

and other detailed information about the sensor are displayed. If a custom name was entered

in the sensor settings it will be used as the caption of the sensor tab. It is not possible to set

a custom name for the internal sensor. Clicking on “Edit Sensor Settings” will show the

“Sensor Settings” dialog which can be used to change sensor properties. For additional

information about changing sensor settings please refer to section “Sensor Settings”.

Main Menu

File

 Exit: Closes the KlimaLogg Pro software.

View

 Show Only Alarm Events: The data area will show only datasets that have triggered

alarm events.

 Show Dew point In Device Overview: Shows or hides dew point columns in the device

overview tab.

 Set Active Channels in Device Overview...: Use the dialog to define which channels

are shown in the device overview tab. For details about how to do this please refer to

section „Active Channels“.

Logger

Settings…: Opens the “Logger Settings” dialog. Here you can find all information and

settings of the currently selected logger. You can find a detailed description of all

settings in section Logger Settings.

 Synchronize Logger…: Allows performing the synchronize process between

KlimaLogg Pro software und KlimaLogg Pro device again. For more information

please refer to section Synchronization.

 Export Data To Text File...: Shows the “Export data“ Dialog. Using this dialog the

recorded data can be written into a text file that can be processed or analyzed

further. For more information please refer to section Export data.

 Remove Logger: This menu entry deletes the current KlimaLogg Pro device including

all recorded data such as history datasets and alarm events. Attention! Deleting the

logger can’t be undone; all recorded data will be lost and can’t be recovered. Please

backup your data before deleting the logger using the menu entry “Logger / Export

Data To Text File...“.

Extras

 Options…: Opens the options dialog. Here you can find all settings of the KlimaLogg

Pro software such as language, temperature format and date format. These settings

will be used in the whole program. For a detailed description of all available options

please refer to section Options.

 Help…: Opens the online help.

 Visit the TFA Homepage…: http://www.tfa-dostmann.de.

 About the Thermo Hygro Logger…: Shows version and copyright information about

the KlimaLogg Pro software.

Toolbar

The toolbar can be used to quickly access often used functions.

The functions are from left to right:

 Select the active KlimaLogg Pro device. If there is more than one KlimaLogg Pro

device synchronized you can select the device to display.

 Logger settings. Opens the “Logger Settings” dialog. Please refer to section Logger

Settings for detailed information about the possible settings.

 Export Data to Text File. Shows the “Data Export“ dialog.

 Delete selected datasets. Deletes the datasets that have been selected in the list.

 Show Only Alarm Events: Only datasets that have triggered alarm events will be

shown in the data area.

 Show Dew point In Device Overview: Shows or hides the dew point columns in the

device overview.

 Show version and copyright information.

Options

You can use the options dialog to change the default settings of the Klimalogg Pro software.

Language:

This option selects the language used in all windows and dialogs of the KlimaLogg Pro

software. If you choose a different language the KlimaLogg Pro software needs to be

restarted.

Date:

Select the format used for displaying dates in the KlimaLogg Pro software.

Time:

Select if time should be displayed in 12 hour or 24 hour format in the KlimaLogg Pro

software.

Temperature:

Select if temperatures should be shown in °C (Celsius) or °F (Fahrenheit) in the KlimaLogg

Pro Software.

Automatic export file:

Select the path and filename where the automatic export file of the KlimaLogg Pro Service

will be stored. The automatic export file contains the last transferred dataset only.

Work as service:

If this option is selected the KlimaLogg Pro service will continue reading data from the device

that is synchronized on channel 1 even if the KlimaLogg Pro Software has been closed. The

KlimaLogg Service is started automatically when the PC starts. There is no need to actually

communication press the USB key on the device once the PC has finished starting.

Show Data Folder:

Opens Windows-Explorer within the Folder were the KlimaLogg Pro software stores its data.

Logger Settings

In the Logger Settings dialog the preferences of the currently selected KlimaLogg Pro device

can be changed.

Logger Name & Logger Channel

Identifies the KlimaLogg Pro device to which the settings in the dialog applies.

Reread All History Data

Clicking this button reads again all data that is stored on the KlimaLogg Pro device and

transfers it to the PC. Already existing datasets will be overwritten.

Show Automatic Export File

Opens Windows Explorer and selects the export file that is used for the current KlimaLogg

Pro device.

Recording Interval

Sets the interval used by the KlimaLogg Pro device for storing measurements.

Reset Min/Max Values

Reset the min./max. values of the KlimaLogg Pro device.

Device Overview Display

Select the visible channels in device overview. Additionally the device overview can be

configured to show alarm events only and if dew point columns should be displayed.

To reread history data, change the recording interval or reset the min/max values, the

KlimaLogg Pro device must be in communication mode. To establish communication mode

press the USB key on the KlimaLogg Pro device.

Export Data

Use the “Export Data” dialog to archive the recorded datasets into a text file.

Time range

Select the time range of the datasets to export. You can find common time ranges in the time

range drop down box or define the exact start and end time.

Data format

The “Use comma instead of point as decimal separator” checkbox determines if values are

formatted with comma or points in the text file.

Target File

Select the folder and filename which will be used to store the datasets. Please make sure

you have write permissions to this location.

Active Channels

Use this dialog to select the channels to be displayed in the device overview tab. You can

hide the channels were no sensor is learned.

Sensor Settings

Use this dialog to change the properties including the alarm settings of a sensor.

You can set the sensor name which will be displayed on the KlimaLogg Pro device. You can

use up to 10 alphanumerical characters for the name of the sensor. This name will also be

used in KlimaLogg Pro software as the tab caption for this sensor. Additionally you can

define the Hi/Lo alarm threshold and activate/deactivate alarms. If you changed the name of

the sensor or alarm settings the changed settings will be transferred to the KlimaLogg Pro

device after clicking OK.

To transfer the settings the KlimaLogg Pro device must be in communication mode. To

establish communication mode please press the USB key on the KlimaLogg Pro device.

Charts

KlimaLoggPro provides the ability to analyze the data collected from the logger and its

sensors using graphical charts of the data.

The x axis display time, the left y axis displays temperature and the right y axis humidty.

Period

Use the period dropdown to select the time period for which the data should be displayed.

The start and end date and time display the exact range of the data record set that will be

used in the chart. These fields can also be used to set the exact time period.

The Selected Period slider shows a graphical representation of the time period. Drag the

handles with the arrows to change the displayed time period.

Data Interval

The Data Interval setting allows you to define how close together the data points are

represented on the chart. A shorter interval will place more data points in the chart, and will

give a more detailed graph line.

Break Interval

This Break Interval property places a space, or break into the chart, if the time amount

between two datasets is greater than the selected value. If the gap between two consecutive

data points is as big as, or bigger than, the chosen break interval then the data points will not

be connected by a line.

An example of this would be if you have a recording interval of 1 minute, and have recorded

data for a full 2 days. Then the logger did not record any data on day 3 (perhaps the batteries

were dead). Then you replace the batteries and data is recorded for another full day on day

4. There is one day of data missing on day 3.

If you generate a chart showing the data from all four days with no break interval, there will

be a straight line connecting the last data point on day 2 (when the recording stopped) to the

first data point on day 4 when the data recording started again. If we enable the break

interval, a space will appear on the chart to represent the missing data.

Sensors

The sensor list provides settings how to display the data for each sensor within the chart.

Use the checkbox in front of the Temperature and Humidity caption to determine if the

sensor value should be displayed in the chart at all. Use the color dropdown to determine the

color of the line that represents the sensor in the chart.

General

The chart settings in the General group allow you to further customize the appearance of the

chart.

Background

Use the color dropdown to set the background color of the chart.

Grid

The Grid checkbox allows you to turn the grid lines in the background of the chart on and off.

Legend

The Legend checkbox turns the legend below the chart on or off. The legend shows which

line in the chart corresponds to which sensor.

Left / Right Axis Min / Max

These settings allow you to provide custom values for the maximum and minimum y axis

values that should be displayed in the chart. If the checkboxes are unchecked KlimaLoggPro

will automatically scale the y axis depending on the data that is selected for display.

TFA Professional Thermo-Hygrometer with Data Logger Function KLIMALOGG PRO User manual

Brand: TFA

Model: Professional Thermo-Hygrometer with Data Logger Function KLIMALOGG PRO

Type: User manual

Download PDF

report

TFA Professional Thermo-Hygrometer with Data Logger Function KLIMALOGG PRO User manual

TFA Professional Thermo-Hygrometer with Data Logger Function KLIMALOGG PRO User manual

Related papers

Other documents