Dell E198WFP User manual

Category
Soundbar speakers
Type
User manual

This manual is also suitable for

Dell™ E198WFP Flat Panel Monitor User's Guide
About Your Monitor
Front View
Back View
Side View
Bottom View
Monitor Specifications
LCD Monitor Quality & Pixel Policy
Caring for your Monitor
Using Your Adjustable Monitor Stand
Attaching the Stand
Organizing Your Cables
Using the Tilt
Removing the Stand
Setting Up Your Monitor
Connecting Your Monitor
Using the Front Panel
Using the OSD
Setting the Optimal Resolution
Using the Dell Soundbar (Optional)
Solving Problems
Troubleshooting Your Monitor
General Problems
Product Specific Problems
Troubleshooting Your Soundbar
Appendix
FCC Identification Information
Safety Information
Contacting Dell
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Information in this document is subject to change without notice.
© 2007-2008 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, Inspiron, Dell Precision, Dimension, OptiPlex, Latitude, PowerEdge, PowerVault, PowerApp, and
Dell OpenManage are trademarks of Dell Inc; Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation; Adobe is a
trademark of Adobe Systems Incorporated, which may be registered in certain jurisdictions. ENERGY STAR is a registered trademark of the U.S.
Environmental Protection Agency. As an ENERGY STAR partner, Dell Inc. has determined that this product meets the ENERGY STAR guidelines for
energy efficiency.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
Model E198WFP
January 2008 Rev. A03
Back to Contents Page
About Your Monitor
Dell™ E198WFP Flat Panel Monitor User's Guide
Front View
Back View
Side View
Bottom View
Monitor Specifications
LCD Monitor Quality & Pixel Policy
Caring for your Monitor
Front View
1. Input signal select button
2. OSD menu / Select button
3. Brightness and Contrast / Down button
4. Auto-adjust / Up button
5. Power On / Off button (with LED indicator)
Back View
1 VESA mounting holes (100mm) (Behind
attached base plate)
Use to mount the monitor.
2 Barcode serial number label Refer to this label if you need to contact Dell for technical support.
3 Security lock slot Use a security lock with the slot to help secure your monitor.
4 Stand removal button Press to release the stand.
5 Regulatory rating label List the regulatory approvals.
6 Dell Soundbar mounting brackets Attach the optional Dell Soundbar.
7 Cable management hole Help organize cables by placing them in the hole.
Bottom View
1 Power connector Insert the power cable.
2 Stand anti-theft feature Mount a 3*8 screw to make the stand undetachable.
3 DVI connector Connect your computer DVI cable.
4 VGA connector Connect your computer VGA cable.
Side View
Left side Right side
Monitor Specifications
Power Management Modes
If you have VESA's DPM™ compliance display card or software installed in your PC, the monitor automatically reduces its power consumption when not in use. This is referred
to as Power Save Mode. The monitor automatically resumes functioning when the system detects input from the keyboard, mouse or other input devices.The following table
shows the power consumption and signaling of this automatic power saving feature:
VESA Modes Horizontal Sync Vertical Sync Video Power Indicator Power Consumption
Normal operation Active Active Active Green 38 W (typical)
Active-off mode Inactive Inactive Blanked Ambers Less than 2 W
Switch off - - - Off Less than 1 W
NOTE: The OSD only functions in the normal operation mode. One of the following messages appears when the Menu or Plus buttons are pressed when in Active-off
mode.
1 : Auto Detect (Analog Input)
In Power Save Mode
Press computer power button
or any key on keyboard or move mouse
or
1 : Auto Detect (Digital Input)
In Power Save Mode
Press computer power button
or any key on keyboard or move mouse
2: Analog Input
In Power Save Mode
Press computer power button
or any key on keyboard or move mouse
or
3: Digital Input
In Power Save Mode
Press computer power button
or any key on keyboard or move mouse
Activate the computer and the monitor to gain access to the OSD
.
This monitor is ENERGY STAR®-compliant as well as TCO '99/'03 power management compatible.
* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.
Pin Assignments
15-pin D-Sub connector
Pin Number Monitor Side of the 15-pin Side Signal Cable
1 Video-Red
2 Video-Green
3 Video-Blue
4 GND
5 Self-test
6 GND-R
7 GND-G
8 GND-B
9 DDC +5V
10 GND-sync
11 GND
12 DDC data
13 H-sync
14 V-sync
15 DDC clock
24-pin Digital-only DVI Connector
Note: Pin 1 is at the top right.
Pin Signal Assignment Pin Signal Assignment Pin Signal Assignment
1 T.M.D.S. Data 2- 9 T.M.D.S. Data 1- 17 T.M.D.S. Data 0-
2 T.M.D.S. Data 2+ 10 T.M.D.S. Data 1+ 18 T.M.D.S. Data 0+
3 T.M.D.S. Data 2 Shield 11 T.M.D.S. Data 1 Shield 19 T.M.D.S. Data 0 Shield
4 No Pin 12 No Pin 20 No Pin
5 No Pin 13 No Pin 21 No Pin
6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield
7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock +
8 No Connect 16 Hot Plug Detect 24 T.M.D.S. Clock -
Plug and Play Capability
You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer with its Extended Display Identification Data (EDID)
using Display Data Channel (DDC) protocols so that the system can configure itself and optimize the monitor settings. Most monitor installations are automatic. You can select
different settings if required.
General
Model number E198WFP
Flat Panel
Screen type Active matrix - TFT LCD
Screen dimensions 19 inches wide(19-inch wide viewable image size)
Preset display area:
Horizontal 408mm / 16.1inches
Vertical 255mm / 10.0 inches
Pixel pitch 0.2835mm
Viewing angle 160° (vertical) typ, 160° (horizontal) typ
Luminance output 300 CD/m ²(typ)
Contrast ratio 1000 to 1 (typ)
Faceplate coating Antiglare with hard-coating 3H
Backlight CCFL (4) edgelight system
Response Time 5ms typical
Resolution
Horizontal scan range 30 kHz to 83 kHz (automatic)
Vertical scan range 56 Hz to 75 Hz (automatic)
Optimal preset resolution 1440 x 900 at 60 Hz
Highest preset resolution 1440 x 900 at 60 Hz
Video Supported Modes
Video display capabilities (DVI playback) 480i/480p/576i/576p/720p/1080i/1080p (Supports HDCP)
Preset Display Modes
The following table lists the preset modes for which Dell guarantees image size and centering:
Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock
(MHz)
Sync Polarity
(Horizontal/Vertical)
VESA, 720 x 400 31.5 70.0 28.3 -/+
VESA, 640 x 480 31.5 60.0 25.2 -/-
VESA, 640 x 480 37.5 75.0 31.5 -/-
VESA, 800 x 600 37.9 60.3 49.5 +/+
VESA, 800 x 600 46.9 75.0 49.5 +/+
VESA, 1024 x 768 48.4 60.0 65.0 -/-
VESA, 1024 x 768 60.0 75.0 78.8 +/+
VESA, 1152 x 864 67.5 75.0 108 +/+
VESA, 1280 x 1024 64.0 60.0 135.0 +/+
VESA, 1280 x 1024 80.0 75.0 135.0 +/+
VESA, 1440 x 900 55.9 60.0 106.5 -/+
Electrical
The following table lists the monitor electrical features:
Video input signals
Analog RGB, 0.7 Volts +/-5%, positive polarity at 75 ohm input impedance
Digital DVI-D TMDS, 600mV for each differential line, positive polarity at 50 ohm input impedance
Synchronization input signals
Separate horizontal and vertical synchronizations, polarity-free TTL level, SOG (Composite SYNC on
green)
AC input voltage / frequency / current 100 to 240 VAC / 50 or 60 Hz +
3 Hz / 2.0A (Max.)
Inrush current
120V:30A (Max.)
240V:60A (Max.)
Physical Characteristics
The following table lists the monitor physical characteristics:
Connector type 15-pin D-subminiature, blue connector; DVI-D, white connector
Signal cable type
Digital: Detachable, DVI-D, Solid pins, shipped detached from the monitor
Analog: Detachable, D-Sub, 15pins, shipped attached to the monitor
Dimensions (with stand)
Height 14.38 inches (364.85 mm)
Width 17.54 inches (445.09 mm)
Depth 5.67 inches (143.90 mm)
Dimensions: (without stand)
Height 11.46 inches (291.19 mm)
Width 17.54 inches (445.09 mm)
Depth 2.32 inches (59.00 mm)
Stand dimensions:
Height 11.40 inches (289.25 mm)
Width 11.52 inches (292.50 mm)
Depth 5.67 inches (143.90 mm)
Weight with packaging 14.26 lbs (6.47 kg)
Weight with stand assembly and
cables
10.58 lbs (4.8 kg)
Weight without stand assembly
(For wall mount or VESA mount
considerations - no cables)
8.16 lbs (3.7 kg)
Weight of stand assembly 2.14 lbs (0.97 kg)
Environmental
The following table lists the environmental condition for monitor:
Temperature
Operating to 35°C (41° to 95°F)
Nonoperating
Storage: -20° to 60°C (-4° to 140°F)
Shipping: -20° to 60°C(-4° to 140°F)
Humidity
Operating 10% to 80% (noncondensing)
Nonoperating
Storage: 5% to 90% (noncondensing)
Shipping: 5% to 90%(noncondensing)
Altitude
Operating 3,657.6m (12,000 ft) max
Nonoperating 12,192 m (40,000 ft) max
Thermal dissipation
256.08 BTU/hour (maximum)
119.5 BTU/hour (typical)
LCD Monitor Quality & Pixel Policy
During the LCD Monitor manufacturing process, it is not uncommon for one or more pixels to become fixed in an unchanging state. The visible result is a fixed pixel that
appears as an extremely tiny dark or bright discolored spot.
In almost every case, these fixed pixels are hard to see and do not detract from display quality or usability. A display with 1 to 5 fixed pixels is considered normal and within
competitive standards. For more information, see Dell Support site at: support.dell.com.
Caring for your Monitor
CAUTION: Read and follow the safety instructions before cleaning the monitor.
CAUTION: Before cleaning the monitor, unplug the monitor power cable from the electrical outlet.
To clean your antistatic screen, slightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the antistatic
coating. Do not use benzene, thinner, ammonia, abrasive cleaners, or compressed air.
Use a slightly dampened, warm cloth to clean the plastics. Avoid using detergent of any kind as some detergents leave a milky film on the plastics.
If you notice a white powder when you unpack your monitor, wipe it off with a cloth. This white powder occurs during the shipping of the monitor.
Handle your monitor with care as darker-colored monitor may scratch and show white scuff marks more than lighter-colored monitor.
To help maintain the best image quality on your monitor, use a dynamically changing screen saver and power off your monitor when not in use.
Back to Contents Page
Back to Contents Page
Using Your Adjustable Monitor Stand
Dell™ E198WFP Flat Panel Monitor User's Guide
Attaching the Stand
Organizing Your Cables
Using the Tilt
Removing the Stand
Attaching the Stand
NOTE: The stand is detached when the monitor is shipped from the factory.
1. Place the stand on a flat surface.
2. Fit the groove on the back of the monitor onto the two tabs on the stand.
3. Lower the monitor so that the monitor mounting area snaps on/locks to the stand.
Organizing Your Cables
After attaching all necessary cables to your monitor and computer, (See Connecting Your Monitor for cable attachment,) use
the cable hole to neatly organize all cables as shown above.
Using the Tilt
You can tilt the monitor to best fit your viewing needs.
Removing the Stand
After placing the monitor panel on soft cloth or cushion, complete the following steps to remove the stand.
1. Place the monitor on a table.
2. Lift the stand away from the monitor while pressing the stand release button.
Back to Contents Page
Back to Contents Page
Setting Up Your Monitor
Dell™ E198WFP Flat Panel Monitor User's Guide
Connecting Your Monitor
Using the Front Panel
Using the OSD Menu
Setting the Optimal Resolution
Using the Dell Soundbar (Optional)
Connecting Your Monitor
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions.
or
1. Turn off your computer and disconnect the power cable.
2. Connect either the white DVI or the blue VGA cable to the connectors on the computer and the monitor.
3. Connect the power cable.
4.
Turn on your monitor and computer. If you do not see an image, push the input select button and ensure the correct input source is selected. If you still do not see an
image, see Troubleshooting your monitor
.
Using the Front Panel
Use the buttons on the front of the monitor to adjust the image settings.
The following table describes the front panel buttons:
Input select
Use the Input Select button to choose between two different video signals that may be connected to your monitor.
NOTE: The floating 'Dell Self-test Feature Check' dialog appears on a black background if the monitor cannot
sense a video signal. Depending upon the selected input, one of the dialogs shown below will scroll continually.
or
or
OSD menu / select
The Menu button is used to open and exit the on-screen display (OSD), and exit from menus and sub-menus. See Using
the OSD Menu.
Down (-) and Up (+)
Use these buttons to adjust (decrease/increase ranges) items in the OSD menu.
Power Button and Indicator
Use the power button to turn the monitor on and off.
The Blue light indicates the monitor is on and fully functional. An amber light indicates power save mode.
Using the OSD Menu
NOTE: If you change the settings and then either proceed to another menu, or exit the OSD menu, the monitor automatically saves those changes. The changes are also
saved if you change the settings and then wait for the OSD menu to disappear.
1. Push the Menu button to open the OSD menu and display the main menu.
Main Menu for Analog (VGA) Input Main Menu for Digital (DVI) Input
or
or
NOTE: Positioning and Image Settings are only available when you are using the analog (VGA) connector.
2. Push the - and + buttons to move between the setting options. As you move from one icon to another, the option name is highlighted. See the table below for a complete list
of all the options available for the monitor.
3. Push the MENU button once to activate the highlighted option.
4. Push - and + button to select the desired parameter.
5. Push MENU to enter the slide bar and then use the - and + buttons, according to the indicators on the menu, to make your changes.
6. Push the MENU button once to return to the main menu to select another option or push the MENU button two or three times to exit from the OSD menu.
Icon Menu and
Submenus
Description
Exit Select to exit the Main menu.
Brightness/
Contrast
Brightness adjusts the luminance of the backlight.
Adjust Brightness first, then adjust Contrast only if further adjustment is necessary.
Push the + button to increase luminance and push the - button to decrease luminance (min 0 ~ max 100).
Contrast adjusts the degree of difference between darkness and lightness on the monitor screen.
Push the + button to increase the contrast and push the - button to decrease the contrast (min 0 ~ max 100).
Positioning:
Horizontal
Vertical
Positioning moves the viewing area around on the monitor screen.
When making changes to either the Horizontal or Vertical settings, no changes occur to the size of the viewing area. The image
shifts in response to your selection.
Minimum is 0 (-) and maximum is 100 (+).
NOTE: When using DVI source, the Positioning option is not available.
Auto Adjust Even though your computer recognizes your monitor on startup, the Auto Adjustment function optimizes the display settings for use
with your particular setup.
Select to activate automatic setup and adjustment. The following dialog appears on a black screen as the monitor self-adjusts to the
current input:
Auto Adjust In Progress
Auto Adjustment allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment, you can further tune your
monitor by using the Pixel Clock (Coarse) and Phase (Fine) controls under Image Settings.
In most cases, Auto Adjust produces the best image for your configuration.
NOTE: When using DVI, Auto Adjust is not available.
Image
settings
The Phase and Pixel Clock adjustments allow you to more closely adjust your monitor to your preference. Select Image Settings in the
main OSD menu to access these settings.
Use the - and + buttons to make adjustments. (Minimum: 0 ~ Maximum: 100)
Pixel Clock
(Coarse)
Phase (Fine)
If satisfactory results are not obtained using the Phase adjustment, use Pixel Clock (Coarse) and then use Phase (fine), again.
NOTE: This function may change the width of the display image. Use the Horizontal function of the Position menu to center the
display image on the screen.
NOTE: When using DVI source, the Image Settings option is not available.
Color
Settings
Blue Preset
Red Preset
Normal
Preset
User Preset
Color Settings adjust the color temperature.
Color Settings has the following options:
Color Management : You can choose to enable or disable this option.
Color Settings Mode : You can choose between a Graphics and a Video mode. If your computer is connected to your monitor, choose
Graphics. If a DVD, STB, or VCR is connected to your monitor, choose Video.
Color Presets: You can choose different color presets for different viewing modes.
You can choose either Graphics or Video under Color Settings Mode.
As soon as choose Graphics,you can choose Normal Preset,Multimedia Preset,Gaming Preset, Red Preset,Blue Preset or User
Preset;
Select Gaming Preset for playing games in your computer.
Select Multimedia Preset to view media applications such as photo,clip.......
Select Red Preset for a warm color.
Select Blue Preset for a cool color.
You can adjust the monitor color using User Preset, R, G, B.Normal Preset mean color temperature 6500K.
There are three video modes:Theater Preset ,Sports Preset, Nature Preset;
Select Theater Preset for playing a movie.
Select Sports Preset for viewing sports.
Select Nature Preset for general viewing.
For general picture or web or watch TV, choose Nature Preset. User can adjust the Hue(Tint)/Saturation based on the
preference.
Select Blue Preset for a bluish tint. This color setting is used for text based applications (spreadsheets, programming, text
editors, etc.).
Select Red Preset for a reddish tint.This color setting is used for color-intensive applications (photograph image editing,
multimedia, movies, etc.).
Select Normal Preset for default color settings. This setting is also the “sRGB” standard default color space.
User Preset: Use the plus and minus buttons to increase or decrease each of the three colors (R, G, B) independently, in single
digit increments, from 0 to 100.
Advanced
Settings
Input Color
Format
Choose the RGB option if monitor is connected to a PC or a DVD using a VGA or a DVI cable. Choose the YPbPr+ option if monitor is
connected to a DVD by a YPbPr cable.
OSD
Settings
Horizontal
Position
Vertical
Position
OSD Hold
Adjust the settings for the OSD, including the location, the amount of time the menu remains on the screen, and the rotation of the
OSD.
Position of the OSD:
To adjust the horizontal position of the OSD, use the - and + buttons, and move OSD to the left and right.
To adjust the vertical position of the OSD, use the - and + buttons, and move OSD down and up.
OSD Hold Time:
The OSD stays active for as long as it is in use. Adjusting the hold time, sets the length of time the OSD remains active after the last
time you pressed a button. Use the - and + buttons to adjust the slider in 5 second increments, from 5 to 60 seconds.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45

Dell E198WFP User manual

Category
Soundbar speakers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI