Midmark Folding Wall Mount Exam Table Installation guide

Midmark
Brand
Midmark
Model
Folding Wall Mount Exam Table
Category
Wall & ceiling mounts accessories
Type
Installation guide

Midmark Folding Wall Mount Exam Table

The Midmark Folding Wall Mount Exam Table is a versatile and space-saving solution for medical or veterinary examination rooms. Here is a brief overview of its key capabilities:

  • Wall-mounted design: The table conveniently folds against the wall when not in use, freeing up valuable floor space.

  • Sturdy construction: The table is constructed with heavy-duty materials and can support a weight capacity of up to 400 lbs.

  • Adjustable height: Its adjustable height feature allows you to customize the working position for optimal comfort and ergonomics.

Midmark Folding Wall Mount Exam Table

The Midmark Folding Wall Mount Exam Table is a versatile and space-saving solution for medical or veterinary examination rooms. Here is a brief overview of its key capabilities:

  • Wall-mounted design: The table conveniently folds against the wall when not in use, freeing up valuable floor space.

  • Sturdy construction: The table is constructed with heavy-duty materials and can support a weight capacity of up to 400 lbs.

  • Adjustable height: Its adjustable height feature allows you to customize the working position for optimal comfort and ergonomics.

Hardware has been included for mounting the folding wall mount exam table into walls with wood studs. You should have four
3/8" diameter 2" long lag bolts and four flat washers.
Begin by determining where the table will be installed. The mounting plate of the table is pre-drilled
with four holes for bolting
the table to the wall. Holes are 16
"
apart to correspond with standard
wall stud placement. If not placing the wall mount table
to align with existing wall studs, modifications to the wall will be necessary. Even when mounting onto studs we recommend
reinforcing the wall by securing a board between the studs.
16" standard
stud spacing
Drill 1/8" dia.
starter holes
for lag bolts
(4 places)
6 5/8"
Drill bottom holes
28" from floor for
36" counter height
Reinforce wall studs
with 2" x 10" board
secured between studs
Pre-drill holes for the lag bolts as shown. To mount the table
at standard 36" counter top height, drill the bottom holes at
28" from floor level.
When bolting the table to the wall, place large flat washers
between the bolt head and table mounting plate.
If mounting the table to a masonry wall, appropriate anchor
hardware should be used.
If the folding wall mount exam table will be
mounted so that it does not correspond with the
wall studs, secure 2" x 10" boards between wall
studs as a mounting surface.
Secure table properly. The folding wall mount table
is only as sturdy as its mounting.
Folding Wall Mount Exam Table Setup Manual
Rev. AA3 (1/22/19)
Note
Refer to chase installation manual for mounting hole locations
in chase cabinet. To install table to chase, use hardware
included with chase cabinet. (3/8โ€ bolts, washers and nuts).
Also use required bracket included in 002-10368-00 kit.
002-10368-00 Service Kit Required
Leveling the Folding Wall Mount Exam Table
1.
2.
3.
4.
Drill and insert screw as shown to insure that the table remains level
Midmark Corporation - Carthage Facilities
1000 Civil War Road
Area 5
Carthage, MO 64836
1-800-643-6275
When bolting the table to the wall, place
large ๎ƒ€at washers between the bolt head
and the table mounting plate.
If top is not level
after mounting -
Loosen screws at
each end of the
slide bracket.
Reposition the
slide bracket until
the table top
is level, then
tighten screws.
Drill a pilot hole
1/8" diameter,
1/2" deep in the
wood through
the center hole
of the bracket.
Install the 1/2"
screw (included)
into the pilot
hole to hold the
bracket in place..
www.midmark.com
  • Page 1 1
  • Page 2 2

Midmark Folding Wall Mount Exam Table Installation guide

Midmark
Brand
Midmark
Model
Folding Wall Mount Exam Table
Category
Wall & ceiling mounts accessories
Type
Installation guide

Midmark Folding Wall Mount Exam Table

The Midmark Folding Wall Mount Exam Table is a versatile and space-saving solution for medical or veterinary examination rooms. Here is a brief overview of its key capabilities:

  • Wall-mounted design: The table conveniently folds against the wall when not in use, freeing up valuable floor space.

  • Sturdy construction: The table is constructed with heavy-duty materials and can support a weight capacity of up to 400 lbs.

  • Adjustable height: Its adjustable height feature allows you to customize the working position for optimal comfort and ergonomics.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents