Midmark Wall Hugger Exam Table Installation guide

Midmark
Brand
Midmark
Model
Wall Hugger Exam Table
Type
Installation guide

Midmark Wall Hugger Exam Table is a medical device designed to provide a stable and comfortable surface for medical examinations and procedures. It is a versatile table that can be mounted on wood stud walls, masonry walls, or metal stud walls, making it suitable for various healthcare settings.

The table's mounting system ensures sturdiness and stability, providing a secure platform for medical professionals to perform examinations and treatments. Its adjustable height allows for customization to accommodate different patient needs and preferences. The table's compact design makes it ideal for space-constrained areas, while its durable construction ensures longevity and reliability.

Midmark Wall Hugger Exam Table is a medical device designed to provide a stable and comfortable surface for medical examinations and procedures. It is a versatile table that can be mounted on wood stud walls, masonry walls, or metal stud walls, making it suitable for various healthcare settings.

The table's mounting system ensures sturdiness and stability, providing a secure platform for medical professionals to perform examinations and treatments. Its adjustable height allows for customization to accommodate different patient needs and preferences. The table's compact design makes it ideal for space-constrained areas, while its durable construction ensures longevity and reliability.

Preparation of wood stud walls
The instructions below show how to properly brace a wood stud wall to securely hang a Wall Hugger
Exam Table. Cross braces need to be installed to minimize flexing. Mounting holes are pre-drilled into the
table mounting brackets 16" apart to correspond with standard wall stud placement. If placement of the
exam table does not match existing wall studs, modifications to the wall will be necessary. Reinforcing the
wall by securing a board between the studs is recommended for both installation on studs or between
studs.
PREPARATION OF MASONRY OR METAL STUD WALLS
To mount Wall Hugger Exam Table on masonry or metal stud walls, a 3/4" x 20" x 50" plywood mounting
plate is recommended. Anchor hardware should be appropriate to the wall construction material. On metal
stud walls, mounting plate should span four studs.
Determine where the table will be
installed. To mount the table at standard
36" counter top height, drill the three
bottom holes 28" above the floor per the
diagram at left. Six 3/8" diameter x 2"
long lag bolts and six flat washers have
been included with the exam table for
installation to wood stud walls. When
bolting the table to the wall, place the
flat washer between the bolt head and
table mounting bracket. See page 2.
Secure table properly. The wall hug-
ger exam table is only as sturdy as
its mounting.
continued
16" Standard
Stud Spacing
16" Standard
Stud Spacing
Drill Bottom
holes 28" from
oor for 36"
counter top.
Reinforced wall studs with 2" x 10 " board secured between
studs
1/8" Diameter starter holes
for lag bolts (6 plc's)
6 5/8"
Bolt Locations.
You must drill
holes through
the metal studs
to allow use of
anchors.
Wall Hugger mount
plate/brackets
Plywood
Metal Studs
1/2"
hole for
anchors/
bolts
(10x)
3/4" Plywood
50" x 20"
3/4" x 20" x 50" Mounting plate detail
3/8" DIA hole for carriage bolts
To mount table (6x)
1
9
17
25
33
41
49
50
1
3.5
10
10 1/8
19
20
Wall Hugger Exam Table Setup Manual
Rev. AA1 (4/24/18)
Installing the Wall Hugger Exam Table
On metal stud walls, anchor the mounting
plywood through the metal studs. Mount
the Wall Hugger Exam Table to the
plywood mounting plate.
On masonry walls, anchor the mounting plywood
to the wall on side opposite of the side the Wall
Hugger Exam Table is to be mounted. Anchor the
Wall Hugger Exam Table with six lag bolts through
the wall and plywood and fasten to plywood
mounting plate with at washers and nuts.
Midmark Corporation - Carthage Facilities
1000 Civil War Road
Area 5
Carthage, MO 64836
1-800-643-6275
Drill and insert screw as shown to insure that the table remains level
If top is not level after
mounting, loosen
screws at each end of
the slide bracket.
1
2
3
4
Reposition the slide
bracket until the table
top is level, then tighten
screws.
Drill a pilot hole 1/8"
diameter, 1/2" deep in
the wood through the
center hole of the
bracket.
Install the 1/2"
screw (included) into
the pilot hole to hold
the bracket in place.
Leveling the Wall Hugger Exam Table
When bolting table to wall, place large
at washer between the bolt head and
the table mounting plate.
Interior Concrete wall
3/4" Plywood (50" x 20")
Metal Stud
3/4" Plywood (50" x 20")
When mounting,
locate bottom holes
28" from floor for
36" counter top
Anchoring Wall Hugger
Exam Table to interior
metal stud wall
Anchoring Wall Hugger Exam
Table to 4" masonry wall
When mounting,
locate bottom holes
28" from floor for
36" counter top
Side view of stud wall
Side view of masonry wall
www.midmark.com
  • Page 1 1
  • Page 2 2

Midmark Wall Hugger Exam Table Installation guide

Midmark
Brand
Midmark
Model
Wall Hugger Exam Table
Type
Installation guide

Midmark Wall Hugger Exam Table is a medical device designed to provide a stable and comfortable surface for medical examinations and procedures. It is a versatile table that can be mounted on wood stud walls, masonry walls, or metal stud walls, making it suitable for various healthcare settings.

The table's mounting system ensures sturdiness and stability, providing a secure platform for medical professionals to perform examinations and treatments. Its adjustable height allows for customization to accommodate different patient needs and preferences. The table's compact design makes it ideal for space-constrained areas, while its durable construction ensures longevity and reliability.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents