Savage A40 Air - Welding Helmet Instructions
These instructions must be read in full before operating the equipment. Failure to follow
these instructions completely may result in reduced or no protection at all.
These Instructions cover Savage A40 Air welding helmet when used with ESAB PAPR (Powered
Air-Purifying Respirator).
These instructions must be read in conjunction with the Savage A40 Welding Helmet User
Instructions supplied with each Welding helmet and the user instructions supplied with each
ESAB PAPR.
Savage A40 air welding helmet and ESAB PAPR
ESAB Part Number
Description
0700500400
Savage A40 Air Black Replaceable Battery
0700002300
ESAB PAPR with Standard Hose 850mm
0700002301
ESAB PAPR with Long Hose 1000mm
Standards:
When used in accordance with the manufacturer’s instructions, the Savage A40 Air, and the
above listed ESAB PAPR units, conform to EN 12941:1998+A2:2008.
CE examination by: BSI Group, UK (0086 Notified Body number)
Donning the welding head piece:
The head harness may be adjusted by following the instructions as detailed in the user
instructions supplied with the helmet.
Fit the head harness on the head and tighten the ratchet by rotating the wheel at the back of
the head harness clockwise.
Cover the front of the head with the face seal and tighten the strap.
Ensure that the head cover is pulled down as far as possible at the back of the head.
If necessary, enlist the help of another person to ensure best-fit and minimal gaps.
IMPORTANT NOTE, the user must ensure that the face seal strap in contact with the user’s
face is in front of the user’s ears and not covering them.
Storage & Transportation:
When not in use or during transportation, the helmet and PAPR units should be stored in the
container in which they were provided, or other similar container, such that they are out of direct
sunlight, not in contact with solvents and cannot be damaged by physical contact with hard
surfaces/items. Do not store outside the temperature range of +0°C to +40°C or with humidity
above 75%RH.
ESAB Welding & Cutting Products, 2800 Airport Road, Denton, TX 76207, USA
Tel: +1-940-566-2000. Customer Care +1-800-426-1888
ESAB AB, S-695 81 Laxå, Sweden, Phone: +46 584 810 00, Fax: +46 584 130 56.
Spares:
Savage A40 Air welding helmet
1. Head/Face seal
0700500405
2. Head Gear including Air Duct
0700500404
1
2
Other helmet spare parts are available in the helmet instruction manual
The PAPR spare parts are listed in table below:
Ordering no.
Description
Notes
0700 002 303
Proban hose cover long
1000 mm
0700 002 304
Proban hose cover standard
850 mm
0700 002 305
Air hose standard
850 mm
0700 002 306
Air hose long
1000 mm
0700 002 307
Comfort belt
0700 002 308
Motor unit
0700 002 309
P3 filter
0700 002 310
Pre-filter Pk 5
0700 002 311
Intelligent charger
0700 002 312
Battery
0700 002 313
Battery HD
0700 002 314
Flexi hose
ESAB Welding & Cutting Products, 2800 Airport Road, Denton, TX 76207, USA
Tel: +1-940-566-2000. Customer Care +1-800-426-1888
ESAB AB, S-695 81 Laxå, Sweden, Phone: +46 584 810 00, Fax: +46 584 130 56.
-
1
-
2
ESAB Savage A40 Air - Welding Helmet Instructions User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ESAB Savage A40 PAPR User manual
-
ESAB A40 PAPR Filter User manual
-
ESAB PAPR System User manual
-
-
ESAB Savage A40 User manual
-
ESAB A20 A30 Light weight automatic welding helmet Declaration of conformity
-
ESAB SAVAGE A40 Welding Helmet User manual
-
-
-
