CAME MTM is a versatile and powerful access control RFID module that can be used to enhance security and convenience in various residential and commercial applications. With its ability to program and manage access via RFID badges, CAME MTM offers a reliable and user-friendly solution for controlling entry to gates, doors, and other secured areas.
CAME MTM is a versatile and powerful access control RFID module that can be used to enhance security and convenience in various residential and commercial applications. With its ability to program and manage access via RFID badges, CAME MTM offers a reliable and user-friendly solution for controlling entry to gates, doors, and other secured areas.
RFID module for access control
MTMRFID
PROGRAMMING MANUAL
EN
E
n
g
l
i
sh
FA01679-EN
ON
1234
SW4
SW2
MASTER
VAS/101
Page 2 - Manual FA01679-EN - 06/2022- © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice.
- Translation of the original instructions
PROGRAMMING STAND-ALONE IN MASTER MODE
To restore module MTMRFID to factory
settings it is necessary to disconnect
the power supply, position DIP1 and
DIP2 of SWITCH SW4 to ON and power
the module again .
After 5 seconds the module restarts and
a sound confi rms the factory settings
have been restored.
RESTORE FACTORY DEFAULT
GENERAL PRECAUTIONS
• Read the instructions carefully before beginning the installation and carry out the procedures as specifi ed by the
manufacturer. • Installation, programming, commissioning and maintenance must only be carried out by qualifi ed, expert
technicians and in full compliance with the applicable law. • Before carrying out any cleaning or maintenance, disconnect
the device from the power supply.
• Only use this product for its intended purpose. Any other use is hazardous.
•
Came
S.p.A. is not liable for any damage caused by improper, erroneous or unreasonable use.
• The product, in its original
packaging supplied by the manufacturer, must only be transported in a closed environment (railway carriage, containers,
closed vehicles). • If the product malfunctions, stop using it and contact customer services at https://www.came.com/
global/en/contact-us or via the telephone number on the website.
The manufacture date is provided in the production batch printed on the product label. If necessary, contact us at
https://www.came.com/global/en/contact-us.
The general conditions of sale are given in the o cial CAME price lists.
LEGISLATIVE REFERENCES
This product complies with the applicable standards in force at the time of manufacturing.
RED
CAME S.p.A. declares that the product described in this manual complies with Directive 2014/53/EU and the Radio
Equipment Regulations 2017.
The full EC declaration of conformity and UK Conformity Assessed (UKCA) marking information can be found at www.
came.com.
DECOMMISSIONING AND DISPOSAL
Dispose of the packaging and the device at the end of its life cycle responsibly, in compliance with the laws in force in the
country where the product is used. The recyclable components are marked with a symbol and the material's ID marker.
THE DATA AND INFORMATION SHOWN IN THIS MANUAL ARE TO BE CONSIDERED AS SUBJECT TO CHANGE AT ANY TIME
AND WITHOUT THE NEED FOR ANY ADVANCE WARNING.
MEASUREMENTS, UNLESS OTHERWISE INDICATED, ARE IN MILLIMETRES.
beeeep
beeeep
beep
beep
ON
1
2
S
S
W
4
O
N
1
S
S
W4
2
beep
beep
O
N
1
S
S
W
4
4
Page 3 - Manual FA01679-EN - 06/2022- © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice.
- Translation of the original instructions
To remove badges from the associated
relay, position DIP2 to ON . When the
red LED on module MTMRFID starts to
fl ash quickly swipe all the badges to
be removed on the reader.
A long beep will confi rm the procedure
was correct .
? In the event of an error, this will be
indicated by 3 fast beeps. Repeat the
stage correctly.
When programming is completed, repo-
sition DIP2 to OFF: the red LED goes out.
Removing badges
To associate badges with the selected
relay, position DIP1 to ON When the
red LED on module MTMRFID starts to
fl ash slowly swipe the badges to be
associated on the reader .
A long beep will confi rm the procedure
was correct.
? In the event of an error, this will be
indicated by 3 fast beeps. Repeat the
stage correctly.
When programming is completed, repo-
sition DIP1 to OFF: the red LED goes out.
Associating badges
This procedure lets you associate a badge with one of the two relays present on the MTMRFID module:
ON Associating badge with relay 1 (NC, NO, C1 terminal) OFF Associating badge with relay 2 (NO, C2 terminal)
To remove lost badges, position DIP4
to ON . When the red LED on module
MTMRFID stays constantly on , swipe
all the badges previously acquired on
the reader.
A beep will confi rm removal of the
badges previously programmed but not
acquired in this stage .
Removing lost badges
? In the event of an error, this will be indicated by 3 fast beeps. Repeat the stage correctly.
When programming is completed, reposition DIP4 to OFF: the red LED goes out.
? For the procedure to be valid at least one previously acquired badge must be swiped.
beep
beep
beep
beep
SW2
SLAVE
VA/08
ETI/XIP
ETI/XIP APP
DVC/IP
35
2*
*
*
*
*
*
*
*
52
5
),'
35
2*
²
35
2*
*
*
*
*
*
*
52
5
),'
35
2*
²
35
2*
5
),'
35
2*
²
Page 4 - Manual FA01679-EN - 06/2022- © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice.
- Translation of the original instructions
To remove badges, put the RFID PROG
jumper of the power supply in the “-”
position . When the red LED on mod-
ule MTMRFID starts to fl ash slowly ,
swipe the badges to be removed on the
reader twice.
A beep will confi rm the procedure was
correct .
? In the event of an error, this will be
indicated by 3 fast beeps. Repeat the
stage correctly.
When programming is completed repo-
sition the RFID PROG jumper as shown
in fi gure: the PROG LED on the power
supply and the red LED on the reader
go out .
Associating badges with VA/08
Removing badges with VA/08
? In the event of an error, this will be indicated by 3 fast beeps. Repeat the
stage correctly.
When programming is completed reposition the RFID PROG jumper as shown in
fi gure: the PROG LED on the power supply and the red LED on the reader go out .
To associate badges, put the RFID PROG
jumper of the power supply in the “+”
position .
When the red LED on module MTMRFID
starts to fl ash quickly , swipe the
badges to be associated on the reader
.
A beep will confi rm the association has
taken place.
PROGRAMMING STAND-ALONE IN SLAVE MODE
SW2
SLAVE
SW2
SLAVE
VA/01 VA/08
PROGPROG
PROG
PROG
>3 s
>3 s
<6 s
<6 s
>3 s
>3 s
VA/01
VA/01
MTMA/01
MTMA/01
MTMV/01
MTMV/01
Page 5 - Manual FA01679-EN - 06/2022- © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice.
- Translation of the original instructions
PROGRAMMING IN SLAVE MODE
Programming relay codes with badges (only with audio module MTMA/01 and video
module MTMV/01)
? For operating details refer also to the manual for audio module MTMA/01 and video module MTMV/01.
Programming relay codes lets you manage the relays present on audio module MTMA/01, video module MTMV/01, or any
eventual VLS/2, via badges.
With VA/01
Press the PROG button until the PROG
LED lights up .
With MTMA/01-MTMV/01 with-
out VA/01
Press the PROG key on the entry pan-
el for at least 3 seconds and release it
within 6 seconds .
Going into Programming
The LED will fl ash to signal entry into programming .
PROGPROG
PROG
PROG
VA/01
VA/01
MTMA/01
MTMA/01
MTMV/01
MTMV/01
5),'
352*
²0
352*
VA/01 - VA/08
VA/01 - VA/08
Page 6 - Manual FA01679-EN - 06/2022- © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice.
- Translation of the original instructions
To associate badges, put the RFID PROG
jumper of the power supply in the “+”
position. The PROG LED on the power
supply and LEDs and will fl ash
quickly .
PROGRAMMING ACCESS CONTROL WITH BADGES
This procedure lets you associate badges with each group of users, identifi ed by a single call, or remove them, to control the
door release in audio module MTMA/01, MTMA/08 and video module MTMV/01, MTMV/08.
A maximum of 5 badges can be associated per group.
Associating badges
With VA/01
Briefl y press the PROG key .
With MTMA/01-MTMV/01 with-
out VA/01
Briefl y press the PROG key on the entry
panel .
The LED on the entry panel and the
PROG LED on the power supply go out.
To associate badges with relays on audio module MTMA/01, video module MTMV/01, or any eventual VLS/2, follow the sequence
in the table. Programming is necessary on each entry panel whose relays you want to control.
With each association a beep will confi rm the procedure is correct.
? In the event of an error, this will be indicated by 3 fast beeps. Repeat the stage correctly.
Sequence Command
+ swipe badge on module MTMRFID on the entry panel to be pro-
grammed Relay 1 on module VLS/2
+ swipe badge on module MTMRFID on the entry panel to be pro-
grammed Relay 2 on module VLS/2
+ swipe badge on module MTMRFID on the entry panel to be pro-
grammed
Auxiliary contact of module MTMA/01
MTMV/01
+ swipe badge on module MTMRFID on the entry panel to be pro-
grammed
Door-release control of module MTMA/01
MTMV/01
Exiting Programming
beeeep
beeeep
5),'
352*
²0
352*
5),'
352*
²0
352*
VA/01 - VA/08
VA/01 - VA/08
VA/01 - VA/08
VA/01 - VA/08
beeeep
beeeep
beeeep
beeeep
Page 7 - Manual FA01679-EN - 06/2022- © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice.
- Translation of the original instructions
To remove badges, put the power sup-
ply's RFID PROG jumper in the “–” po-
sition.
The PROG LED on the power supply and
LEDs and will fl ash slowly .
Approach the badge relating to a group
to the reader and swipe it.
If the badge is valid the LED on the
entry panel will stay constantly on.
Swipe the badge again to confi rm the
operation.
A long beep will confi rm the procedure
was correct .
? In each of the two stages of de-
letion any error condition will be sig-
nalled by three fast beeps. Repeat the
stage correctly.
To delete all the badges relating to a
group, press the call key relating to
the group whose badges you want to
delete.
Removing badges
Press the call key of the group the
badge is to be associated with. A long
beep will confi rm the procedure was
correct .
? In the event of an error, this will be
indicated by 3 fast beeps. Repeat the
stage correctly.
When programming is completed, posi-
tion the RFID PROG jumper as shown in
fi gure .
Swipe the badge to be programmed.
If the badge is valid, the LED on the
entry panel stays constantly on and it is
possible to continue with programming
.
If the code is valid, the LED stays constantly on and it is possible to cancel.
Press the call key relating to the group again.
A long beep will confi rm the procedure was correct .
? In each of the two stages of deletion any error condition will be signalled by
three fast beeps. Repeat the stage correctly.
When programming is completed, position the RFID PROG jumper as shown in fi gure
.
CAME S.p.A.
Via Martiri Della Libertà, 15
31030 Dosson di Casier - Treviso - Italy
tel. (+39) 0422 4940 - fax. (+39) 0422 4941
[email protected] - www.came.com
Page 8 - Manual FA01679-EN - 06/2022- © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice.
- Translation of the original instructions
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
CAME MTM is a versatile and powerful access control RFID module that can be used to enhance security and convenience in various residential and commercial applications. With its ability to program and manage access via RFID badges, CAME MTM offers a reliable and user-friendly solution for controlling entry to gates, doors, and other secured areas.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
CAME MTMRFID Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Schneider Electric XGCS491B201 Standalone RFID Reader Operating instructions
-
Comelit SK9001I Technical Manual
-
-
-
DELTA DORE LB 2000 TYXAL+ Installation guide
-
Videofied XT-iP 620 Install Manual
-
Bticino 343071 Operating instructions
-
-
CDVI A10U48 Mid and Long Range UHF Reader User manual
-