Hobart NGW Wrapper is a versatile and efficient packaging system designed to meet the demands of high-volume wrapping applications. With its advanced features and user-friendly design, the NGW Wrapper streamlines the packaging process, ensuring optimal product protection and presentation.
Key Capabilities:
- Automatic Operation: The wrapper automatically centers the package on the intake and initiates the wrapping process, freeing up the operator for other tasks.
- Error Detection: In case of any malfunction, the wrapper shuts down automatically and displays error messages on the console, enabling prompt troubleshooting.
Hobart NGW Wrapper is a versatile and efficient packaging system designed to meet the demands of high-volume wrapping applications. With its advanced features and user-friendly design, the NGW Wrapper streamlines the packaging process, ensuring optimal product protection and presentation.
Key Capabilities:
- Automatic Operation: The wrapper automatically centers the package on the intake and initiates the wrapping process, freeing up the operator for other tasks.
- Error Detection: In case of any malfunction, the wrapper shuts down automatically and displays error messages on the console, enabling prompt troubleshooting.
NGW Wrapping System – Operating & Cleaning Tips
WRAPPING
1. Make sure all product is inside the tray.
2. Be sure to center the package on the intake.
3. If the wrapper shuts down automatically, an error condition has occured. Carefully read the message on the console
display and follow appropriate procedures to correct the problem(s).
CLEANING
Prior to cleaning, power down the touch screen, printer and wrapper. Unthread the lm from the lm selector.
Disconnect power source to wrapper before cleaning. Cover the printer and console with
the provided covers before hosing down the wrapper.
Use of high pressure washing system will cause damage to the wrapper.
To appropriately clean each component of the system, refer to the following component cleaning table.
Component Explanation
Rear Film Chamber, Canopy, and
Film Chamber Doors
Clean as needed with a soft cloth moistened with a mild detergent and water. Rinse and allow
to air dry.
Covers (External - Plastic) and
Side Panels (Stainless Steel)
Clean as needed by using a soft cloth moistened with a mild detergent and water. Rinse and
allow to air dry.
Sealer Belt Hot surface. Do not touch.
Clean as needed by using a soft cloth moistened with a mild detergent and water. Rinse and
allow to air dry.
Intake Conveyor Area and Weigher
Rods
Clean as needed by using a long-handled brush or a moist cloth. Weigher rod plates and intake
pan can be removed and cleaned in a sink with mild detergent and water. Note the location of
the locating tab on the intake pan. Use a long-handled brush for additional cleaning of the belts.
Replace weigher rod plates and intake pan after cleaning. Rinse and allow to air dry. Replace
weigher rod plates before power up or weigher will come up outside maintenance zone.
Package Hold Down Lift upward and clean as needed with a soft cloth moistened with a mild detergent and water.
Rinse and allow to air dry.
Rubber Pads, Side Clamp Gripper
and Rubber Roller (in lm selector)
Clean as needed with Hobart cleaning solvent or isopropyl alcohol.
Front, Rear and Side Underfolders Clean as needed by using a soft cloth moistened with a mild detergent and water. Rinse and
allow to air dry.
Elevator Area Clean as needed by using a soft cloth. Open the canopy and the side doors to get access to the
elevator area. Rinse and allow to air dry. A soft brush may be required to reach conned areas.
©HOBART, 2017 FORM 35559 (March 2017)
FORM 35559 (March 2017) PRINTED IN U.S.A.
NGW Wrapping System – Operating & Cleaning Tips
FILM LOADING
Keep the lm as straight as possible through the threading process.
The diagram shows the different ways to load lm.
NOTE: Some wrappers only have one spool for lm. The following
instructions show a one spool system. The two spool system is similar.
To thread lm:
1. PRESS the STOP (red) button and allow the machine to stop.
2. Open the rear doors.
3. Release feed rollers by pulling the lm lever down.
4. Turn lm supply knob counterclockwise until roll locks are open
1 to 2 inches wider than the roll width.
The lm roll is under slight tension. Use care
when depressing the roll locks to avoid pinching hands.
5. Depress the roll locks and remove the empty lm roll.
The roll locks are spring loaded. Use care when
loading lm roll onto to the shaft to avoid pinching hands.
6. Firmly slide the lm roll onto the shaft, past the roll locks; then
tighten the knob as much as possible turning clockwise. The
roll will automatically center itself as you tighten the knob.
7. Slide the lm tray out, exposing the lm combs.
8. Pull the lm end in a downward direction (loading top roll)
or upward (loading lower roll) to the front of the guide shaft
continuing around the shaft toward the extended lm tray.
9. Put the lm over the tip of your ngers and push through the opening, between the metal and rubber rollers.
Make sure the lm gets to the ends of the lm combs, securing the lm end down over the combs.
10. Pull the lm lever upward, ensuring its full engagement.
11. Close the rear doors.
12. PRESS the ON (green) button. Wait for a steady light, no blink mode.
13. From any screen, TOUCH the Menu Icon . TOUCH Wrapper Settings.
14. You should now see the Wrapper Settings Screen.
NOTE: Depending on the conguration of the wrapper, there may be only
one lm width listed.
15. If the lm width installed is different than the
displayed width, SELECT the lm width and
TOUCH the Load button beside lm width.
16. The wrapper will position lm, cut any excess
lm and set itself (home) for operation.
17. TOUCH home icon to exit this screen.
18. PRESS the STOP (red) button and allow the
machine to stop.
19. Lift the canopy and remove excess lm.
20. Close canopy.
21. PRESS the ON (green) button. It will be
a steady light, no blink mode. Ready for
operation.
Narrow or
Wide Film
Wrapper Settings Screen
-
1
-
2
Hobart NGW Wrapper is a versatile and efficient packaging system designed to meet the demands of high-volume wrapping applications. With its advanced features and user-friendly design, the NGW Wrapper streamlines the packaging process, ensuring optimal product protection and presentation.
Key Capabilities:
- Automatic Operation: The wrapper automatically centers the package on the intake and initiates the wrapping process, freeing up the operator for other tasks.
- Error Detection: In case of any malfunction, the wrapper shuts down automatically and displays error messages on the console, enabling prompt troubleshooting.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Hobart EWS-3 Wrapper User manual
-
-
-
-
-
-
-
-
-
Other documents
-
Krone Comprima CF 155 XC Comprima CV 150 XC,Comprima CV 210 XC Operating instructions
-
-
-
-
MASCAR 5100 S Use & Maintenance Manual
-
Miller JG056098 Owner's manual
-
-
-
Xerox 180 User guide
-
Brady Wraptor User manual
