Black & Decker BCD001 User manual

Brand: Black & Decker

Model: BCD001

Category: Cordless screwdrivers

Type: User manual

Black & Decker BCD001: Your powerful and versatile tool for a variety of drilling and screwdriving tasks. Tackle wood, metal, and plastic projects with ease. Its user-friendly design and safety features make it ideal for DIY enthusiasts and professionals alike. Experience precise control and efficiency in every job.

www.blackanddecker.co.uk

567

BCD001

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

B C

D E

90634972

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

Intended use

Your BLACK+DECKER BCD001 - Drill, has been designed for

screwdriving applications and for drilling in wood, metal and

plastics. This tool is intended for consumer use only.

Safety instructions

General power tool safety warnings

Warning! Read all safety warnings and all

instructions. Failure to follow the warnings

and instructions listed below may result in

electric shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in all of the warnings listed below refers

to your mains operated (corded) power tool or battery oper-

ated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

b. Do not operate power tools in explosive atmospheres,

such as in the presence of ammable liquids, gases

or dust. Power tools create sparks which may ignite the

dust or fumes.

c. Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs

with earthed (grounded) power tools. Unmodied plugs

and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock

if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

e. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the inuence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

b. Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

c. Prevent unintentional starting. Ensure the switch is in

the off-position before connecting to power source

and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or

energising power tools that have the switch on invites

accidents.

d. Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewellery or long hair

can be caught in moving parts.

g. If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

2 2

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

4. Power tool use and care

a. Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do

the job better and safer at the rate for which it was

designed.

b. Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d. Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tools

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools.

f. Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5. Battery tool use and care

a. Recharge only with the charger specied by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of re when used with

another battery pack.

b. Use power tools only with specically designated

battery packs. Use of any other battery packs may create

a risk of injury and re.

c. When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys,

nails, screws, or other small metal objects, that can

make a connection from one terminal to another.

Shorting the battery terminals together may cause burns

or a re.

d. Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, ush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6. Service

a. Have your power tool serviced by a qualied repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

Warning! Additional safety warnings for

drills

u Use auxiliary handles supplied with the tool. Loss of

control can cause personal injury.

u Hold power tool by insulated gripping surfaces when

performing an operation where the cutting accessory

may contact hidden wiring. Cutting accessory contacting

a "live" wire may make exposed metal parts of the power

tool "live" and could give the operator an electric shock.

u Hold power tool by insulated gripping surfaces, when

performing an operation where the fastener may

contact hidden wiring. Fasteners contacting a "live" wire

may make exposed metal parts of the power tool "live"

and could give the operator an electric shock.

u Use clamps or another practical way to secure and

support the workpiece to a stable platform. Holding the

work by hand or against your body leaves it unstable and

may lead to loss of control.

u Before drilling into walls, oors or ceilings, check for the

location of wiring and pipes.

u Avoid touching the tip of a drill bit just after drilling, as it

may be hot.

u The intended use is described in this instruction manual.

The use of any accessory or attachment or performance

of any operation with this tool other than those recom-

mended in this instruction manual may present a risk of

personal injury and/or damage to property.

Safety of others

u This tool is not intended for use by persons (including

children) with reduced physical, sensory or mental capa-

bilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use

of the tool by a person responsible for their safety.

u Children should be supervised to ensure that they do not

play with the appliance.

Residual risks

Additional residual risks may arise when using the tool which

may not be included in the enclosed safety warnings. These

risks can arise from misuse, prolonged use etc.

Even with the application of the relevant safety regulations

and the implementation of safety devices, certain residual

risks can not be avoided. These include:

u Injuries caused by touching any rotating/moving parts.

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

u Injuries caused when changing any parts, blades or ac-

cessories.

u Injuries caused by prolonged use of a tool. When using

any tool for prolonged periods ensure you take regular

breaks.

u Impairment of hearing.

u Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially

oak, beech and MDF.)

Vibration

The declared vibration emission values stated in the technical

data and the declaration of conformity have been measured

in accordance with a standard test method provided by EN

60745 and may be used for comparing one tool with another.

The declared vibration emission value may also be used in a

preliminary assessment of exposure.

Warning! The vibration emission value during actual use of

the power tool can differ from the declared value depending

on the ways in which the tool is used. The vibration level may

increase above the level stated.

When assessing vibration exposure to determine safety

measures required by 2002/44/EC to protect persons regularly

using power tools in employment, an estimation of vibration

exposure should consider, the actual conditions of use and the

way the tool is used, including taking account of all parts of the

operating cycle such as the times when the tool is switched off

and when it is running idle in addition to the trigger time.

Labels on tool

The following symbols are shown on the tool along with the

date code:

Warning! To reduce the risk of injury, the user

must read the instruction manual.

Additional safety instructions for batteries and

chargers (Not provided with the tool)

Batteries

u Never attempt to open for any reason.

u Do not expose the battery to water.

u Do not store in locations where the temperature may

exceed 40 °C.

u Charge only at ambient temperatures between 10 °C and

40 °C.

u Charge only using the charger provided with the tool.

u When disposing of batteries, follow the instructions given

in the section "Protecting the environment".

Do not attempt to charge damaged batteries.

Chargers

u Use your BLACK+DECKER charger only to charge the

battery supplied with the tool. Other batteries could burst,

causing personal injury and damage.

u Never attempt to charge non-rechargeable batteries.

u Have defective cords replaced immediately.

u Do not expose the charger to water.

u Do not open the charger.

u Do not probe the charger.

The charger is intended for indoor use only.

Read the instruction manual before use.

Electrical safety

Your charger is double insulated; therefore no

earth wire is required. Always check that the

mains voltage corresponds to the voltage on

the rating plate. Never attempt to replace the

charger unit with a regular mains plug.

u If the supply cord is damaged, it must be replaced by the

manufacturer or an authorised BLACK+DECKER Service

Centre in order to avoid a hazard.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Forward/reverse slider

3. Torque adjustment collar

4. Keyless chuck

5. LED work light

6. Battery

7. Battery release button

Assembly

Use

Warning! Let the tool work at its own pace. Do not overload.

Charging the battery (g. A1, A2)

The battery needs to be charged before rst use and whenev-

er it fails to produce sufcient power on jobs that were easily

done before. The battery may become warm while charging;

this is normal and does not indicate a problem.

Warning! Do not charge the battery at ambient temperatures

below 10 °C or above 40 °C.

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

Recommended charging temperature: approx. 24 °C.

Note: The charger will not charge a battery if the cell

temperature is below approximately 10 °C or above 40 °C.

The battery should be left in the charger and the charger

will begin to charge automatically when the cell tempera-

ture warms up or cools down.

u Plug the charger (8) into any standard 230 Volts 50 Hz

electrical outlet.

u Slide the battery pack (6) into the charger as shown in

gure A1, A2.

The LED (8a) will ash indicating that the

battery is being charged.

The completion of charge is indicated by the

LED (8a) remaining on continuously. The

pack is fully charged and may be used at this

time or left on the charger.

Warning! re Hazard. When removing the charger from the

battery, be sure to unplug the charger from the outlet rst, then

remove the battery from the charger.

Charger diagnostics

This charger is designed to detect certain problems that can

arise with the battery packs or the power source. Problems

are indicated by one LED ashing in different patterns.

Bad battery

The charger can detect a weak or damaged

battery. The LED ashes in the pattern indi-

cated on the label. If you see this bad battery

blink pattern, do not continue to charge the battery. Return it

to a service center or a collection site for ecycling.

Hot/cold pack delay

When the charger detects a battery that

is excessively hot or excessively cold, it

automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery has normalized. After

this happens, the charger automatically switches to the Pack

Charging mode. This feature ensures maximum battery life.

The light ashes in the pattern indicated on the label.

Leaving the battery in the charger

The charger and battery pack can be left connected with

the LED glowing indenitely. The charger will keep the

battery pack fresh and fully charged. This charger features

an automatic tune-up mode which equals or balances the

individual cells in the battery pack to allow it to function at

peak capacity. Battery packs should be tuned up weekly or

whenever the battery no longer delivers the same amount

of work. To use the automatic tune-up mode, place the

battery pack in the charger and leave it for at least 8 hours.

Important charging notes

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 18 ° – 24 °C. DO NOT charge the battery pack in

an air temperature below +4.5 °C), or above +40 °C. This

is important and will prevent serious damage to the battery

pack.

u The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulated trailer.

u If the battery pack does not charge properly:

u Check operation of receptacle by plugging in a lamp

or other appliance;

u Check to see if receptacle is connected to a light

switch which turns power off when you turn out

the lights;

u Move the charger and battery pack to a location

where the surrounding air temperature is

approximately 18 ° – 24 °C;

u If charging problems persist, take the tool, battery

pack and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufcient power on jobs which were easily

done previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse effect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil, or any buildup of metallic particles

should be kept away from charger cavities. Unplug the

charger before attempting to clean.

u Do not freeze or immerse the charger in water or any

other liquid.

Installing and removing the battery pack from the

tool (g. B)

Warning! Make certain the lock-off button (2) is engaged to

prevent switch actuation before removing or installing battery.

To install battery pack:

u Insert battery pack (6) into tool, until an audible click is

heard (g. B)

Removing the battery pack from the tool (g. C)

u Depress the battery release button (7) as shown in (g. C)

and pull battery pack (6) out of tool.

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

Operating Instructions

Torque control (g.D)

This tool is tted with a torque adjustment collar (3) to select

the operating mode and to set the torque for tightening

screws. Large screws and hard workpiece materials require

a higher torque setting than small screws and soft workpiece

materials.

u For drilling in wood, metal and plastics, set the collar to

the drilling position symbol

u For screwdriving, set the collar to the desired setting. If you

do not yet know the appropriate setting, proceed as

follows:

u Set the collar to the lowest torque setting.

u Tighten the rst screw.

u If the clutch ratchets before the desired result is achieved,

increase the collar setting and continue tightening the

screw. Repeat until you reach the correct setting. Use this

setting for the remaining screws.

Keyless chuck (g. E)

Warning! Make certain the lock-off button (2) is engaged to

prevent switch actuation before installing or removing acces-

sories.

To insert a drill bit or other accessory:

u Grasp the rear half of the chuck with one hand and use

your other hand to rotate the front half in the counterclock-

wise direction, as viewed from the chuck end.

u Insert the bit or other accessory fully into the chuck, and

tighten securely by holding the rear half of the chuck and

rotating the front portion in the clockwise direction as

viewed from the chuck end.

Warning! Do not attempt to tighten drill bits (or any other ac-

cessory) by gripping the front part of the chuck and turning the

tool on. Damage to the chuck and personal injury may occur

when changing accessories.

Selecting the direction of rotation (g. F)

For drilling and tightening screws, use forward (clockwise)

rotation. For loosening screws or removing a jammed drill bit,

use reverse (counterclockwise) rotation.

uTo select forward rotation, push the forward/reverse slider

(2) to the left.

uTo select reverse rotation, push the forward/reverse slider

to the right.

Warning! Never change the direction of rotation while the

motor is running.

Drilling/screwdriving

u Select forward or reverse rotation using the forward/re-

verse slider (2).

u To switch the tool on, press the switch (1). The tool speed

depends on how far you press the switch.

u To switch the tool off, release the switch.

Hints for optimum use

Drilling

u Use sharp drill bits only.

u Support and secure work properly, as instructed in the

Safety Instructions.

u Use appropriate and required safety equipment, as

instructed in the Safety Instructions.

u Secure and maintain work area, as instructed in the

Safety Instructions.

u Run the drill very slowly, using light pressure, until

the hole is started enough to keep the drill bit from slipping

out of it.

u Apply pressure in a straight line with the bit. Use enough

pressure to keep the bit biting but not so much as to stall

the motor or deect the bit.

u Hold the drill rmly with two hands to control its twisting

action.

u DO NOT CLICK THE TRIGGER OF A STALLED DRILL

OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE

TO THE DRILL CAN RESULT.

u Minimize stalling on breakthrough by reducing pressure

and slowly drilling through the last part of the hole.

u Keep the motor running while pulling the bit out of a drilled

hole. This will help reduce jamming.

u Make sure switch turns drill on and off.

Drilling in wood

Holes in wood can be made with the same twist drill bits used

for metal or with spade bits. These bits should be sharp and

should be pulled out frequently when drilling to clear chips

from the utes.

Drilling in metal

Use a cutting lubricant when drilling metals. The exceptions

are cast iron and brass which should be drilled dry. The cutting

lubricants that work best are sulfurized cutting oil or lard oil.

Screwdriving

u Always use the correct type and size of screwdriver bit.

u If screws are difcult to tighten, try applying a small

amount of washing liquid or soap as a lubricant.

u Always hold the tool and screwdriver bit in a straight line

with the screw

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

Troubleshooting

Problem Possible cause Possible solution

Unit will not start. Battery pack not

charged.

Check battery pack charg-

ing requirements

Battery pack will not

charge.

Charger not plugged

in.

Surrounding air

temperature too hot or

too cold.

Plug charger into a work-

ing outlet.

Move charger and battery

pack to a surrounding air

temperature of above 40

degrees F (45ºC) or below

105 degrees F (+40.5ºC)

Unit shuts off

abruptly.

Battery pack has

reached its maximum

thermal limit.

Out of charge. (To

maximize the life of

the battery pack it is

designed to shutoff

abruptly when the

charge is depleted

Allow battery pack to cool

down.

Place on charger

and allow to charge.

Maintenance

Your BLACK+DECKER tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regular cleaning.

Your charger does not require any maintenance apart from

regular cleaning.

Warning! Before performing any maintenance on the tool,

remove the battery from the tool. Unplug the charger before

cleaning it.

u Regularly clean the ventilation slots in your tool and

charger using a soft brush or dry cloth.

u Regularly clean the motor housing using a damp cloth.

Do not use any abrasive or solvent-based cleaner.

u Regularly open the chuck and tap it to remove any dust

from the interior.

Protecting the environment

Separate collection. Products and batteries

marked with this symbol must not be disposed

of with normal household waste.

Products and batteries contain materials that can be recov-

ered or recycled, reducing demand for raw materials.

Please recycle electrical products and batteries accord-

ing to local provisions. Further information is available at

www.2helpU.com

Technical data

BCD001

Voltage V

No-load speed Min

-1

0 - 600

Max. torque Nm 37

Chuck capacity mm

1-10

Max Drilling capacity

Steel/wood mm 10/25

Weight kg

0.8 (with battery 1.2)

Charger 90621477 90590289-05 90634972

Input voltage V

230 230 230

Output voltage V

18 18 18

Current mA 200 400 1A

Approx. charge

time

Hours 8 3 - 5 1.5

Battery

BL1518

Voltage V

Capacity Ah

1.5

Type Li-Ion

Level of sound pressure according to EN 60745:

Sound pressure (L

) 70.0 dB(A), uncertainty (K) 3 dB(A)

Sound power (L

) 81.0 dB(A), uncertainty (K) 3 dB(A)

Vibration total values (triax vector sum) according to EN 60745:

Drilling into metal (a

h, D

) 1.2 m/s

, uncertainty (K) 1.5 m/s

Screwdriving (a

) 1.0 m/s

, uncertainty (K) 1.5 m/s

EC declaration of conformity

MACHINERY DIRECTIVE

BCD001 - Drill, Screwdriver

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

Black & Decker declares that these products described under

"technical data" are in compliance with:

2006/42/EC, EN60745-1:2009+A11:2010, EN60745-2-1:2010,

EN60745-2-2:2010.

These products also comply with Directive 2014/30/EU and

2011/65/EU. For more information, please contact Black &

Decker at the following address or refer to the back of the

manual.

The undersigned is responsible for compilation of the techni-

cal le and makes this declaration on behalf of

Black & Decker.

R. Laverick

Engineering Manager

Black & Decker Europe, 210 Bath Road, Slough,

Berkshire, SL1 3YD

United Kingdom

03/04/2018

Guarantee

Black & Decker is condent of the quality of its products

and offers consumers a 24 month guarantee from the date

of purchase. This guarantee is in addition to and in no way

prejudices your statutory rights. The guarantee is valid within

the territories of the Member States of the European Union

and the European Free Trade Area.

To claim on the guarantee, the claim must be in accordance

with Black&Decker Terms and Conditions and you will need to

submit proof of purchase to the seller or an authorised repair

agent.

Terms and conditions of the Black&Decker 2 year guarantee

and the location of your nearest authorised repair agent

can be obtained on the Internet at www.2helpU.com, or by

contacting your local Black & Decker ofce at the address

indicated in this manual.

Please visit our website www.blackanddecker.co.uk to register

your new Black & Decker product and receive updates on new

products and special offers.

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

ENGLISH

(Original instructions)

N566178 REV-0 04/2018

Australia Black & Decker (Australia) Pty. Ltd. Tel. 03-8720 5100

20 Fletcher Road, Mooroolbark, Fax 03-9727 5940

Victoria, 3138

New Zealand Black & Decker Tel. +64 9 259 1133

5 Te Apunga Place Fax +64 9 259 1122

Mt Wellington

Aukland 1060

United Kingdom & Black & Decker Tel. 01753 511234

Republic Of Ireland 210 Bath Road Fax 01753 512365

www.blackanddecker.co.uk Slough, Berkshire SL1 3YD

[email protected]

Black & Decker BCD001 User manual

Brand: Black & Decker

Model: BCD001

Category: Cordless screwdrivers

Type: User manual

Download PDF

report

Black & Decker BCD001 User manual

Black & Decker BCD001 User manual

Related papers

Other documents