Pyle PWLB121 Installation guide

Pyle
Brand
Pyle
Model
PWLB121
Category
Flat panel desk mounts
Type
Installation guide
TV size rang 10 24：" "~
According to VESA 75/100 standard
Can tilt and fold the Bracket
Step4:Step4:
2.Roll control in little range
Loosen left and right tension screws with supplied Hex Wrench .Adjust
display for desired angle ,and then re-tighten tension screws .As shown
in Fig4b .
2.Roll control in little range
3.Roll control in great range
Pull the display ,make distance between display and wall is maximum .
Circumvolve display in horizontal direction, adjust it for desired angle .
As shown in Fig4c .
3.Roll control in great range
4.Withdraw the display
fold the Bracket to shorten the distance between display and wall ,let
display cling the wall in vertical direction .
4.Withdraw the display
-4--4-
Flat Panel Fixed Mount
INSTALLATION GUIDE
Item No.:PWLB121Item No.:PWLB121
Important: If don't understand about right install ways, please
consult to normal installing specialist.
Important:
Max load capacity:15Kg/33lbs
1.Vertical title
Loosen tilt tension screws with supplied Hex Wrench .Adjust display for
desired tilt angle ,and then re-tighten tension screws .As shown in Fig4a .
1.Vertical title
-2-
-3-
Parts:Parts:
NO
Qty
Name
A
B
D
C
E
F
4
4
4
4
2
2
M4 8mm bolt
M5 8mm bolt
M4 mm bolt12
M5 12mm bolt
Long bolt
Wall anchor
Hex Wrench
G
1
A
B
C
D
EF
G
Wall bracket
Fixed plate
If mounting to cement and beton wall,making mark on the wall directly.
Use a 3mm drill bit,and dill 50mm deepholes.
Use a 11mm drill bit, and dill 50mm deep holes.
Insert wall anchors(F) into the mounting holes and slightly tap them flush
to the wall with a hammer.
Wall anchor should only be used for Cement and Beton mounting.
Never use wall anchors in drywall to install bracket.
Use wall mount as templet,let Bracket flex at the position determined before.
And making a mark in the center of batten.
Note:
Carefully:
Wooden Studs
Cement and Beton
—
—
Note:
Carefully:
Wooden
Studs
Cement
and Beton
—
—
Check your TV manual and confirm the diameter of bolts to be use ,or choose
appropriate bolts according to size ,heigh ,and position of the holes on your
TV .Put up the TV with an assistant in fitting position on the Mounting head.
As shown in Fig 2.
Fig2
Fig3
Shoulder Tension
Swing Arm Tension
Wall Mount Plate
Wrist Hinge Tension
Tilt Tension
Mounting Head
Fig1
Step2 nfold the Arm Assembly:UStep2 nfold the Arm Assembly:U
Considering display with varied”VESA”
standard connects with stand directly. This
product establishes two kinds of installing
styles which is according with “ VESA”
standard.
A-VESA 75(75mmx75mm)
B-VESA 100(100mmx100mm)
If the installing hole of your display is not
”VESA” standard, you need an optional
carrying instrument to attach the display to
the stand.If need carrying instrument,
pleasecontactwithyourdealer.
Step1 Choose your installing location on the TV panel:.
Step1 Choose your installing location on the TV panel:.
Important:Make sure that there is adequate mounting space available for the
display,considering the display dimensions.Using a electronic stake detector
in that mounting location,which is in center of stake.Making mark in the center
of stake on the wall directly .
Important:
Using provided Long bolt install Bracket to the wall.
Carefully :D
D
on't force the bolt to LCD hole ,avoiding damage to people or
instrument. on't use electronics drill to fasten screw .
Carefully :
Step3: Intalling displayStep3: Intalling display
  • Page 1 1
  • Page 2 2

Pyle PWLB121 Installation guide

Pyle
Brand
Pyle
Model
PWLB121
Category
Flat panel desk mounts
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents