NCR 7402-K568 Kit Instructions

Brand: NCR

Model: 7402-K568

Type: Kit Instructions

7402‐K568

WallMountBracketwith

WideKeyboardShelf

KitInstructions



IssueB

Revision Record

Issue Date Remarks

A May2006 Firstissue

B May2007 Added7404support

 





7401-K568 1

Introduction

Note: ThiskitistheRoHSversionof7402‐K543.

ThiskitisusedtomountanNCR7402/7404w/FixedAngleMounttoa

wall.ThemounthasaslidingkeyboardShelfforthefollowing

keyboards(orderedseparately):

• 2336‐K100CherryKeyboardw/Trackball;PS/2Serial.

• 2336‐K634CherryKeyboard

w/Trackball;USB

• 2336‐K212RuggedStormKeyboardUSLayout;USB

23430



2 7401-K568

Installation Procedure

1. ReleasetheCableChainfromtheCableChainBracketbypressing

downandpivotingoutonthelastlinkintheCableChainLinkas

shownbelow.

Press Downward

Pivot Outward

18522a

Cable Chain Bracket



7401-K568 3

2. RemovethescrewsthatsecuretheKeyboardShelftotheBottom

Plate.

17364

4 Screws



3. RemovetheKeyboardShelffromtheBottomPlate.

17365



4 7401-K568

4. ReleasetheCableChainfromtheCableChainBracketbyliftingup

onthelastlinkintheCableChainandpivotingitout.

18523

Cable Chain Bracket

1. Lift Up

2. Pivot Out



7401-K568 5

5. InstalltheKeyboard.TheKeyboardinstallationproceduresvary,

dependingonwhichkeyboardyouhave.

2336‐K020,2336‐K100or2336‐K634CherryKeyboardw/Trackball

a. InserttheKeyboardintotheKeyboardShelf.

18524

6 7401-K568

b. Usinganutdriver,installthetwoKeyboardLockingBrackets.

22579

Locking

Bracket

7401-K568 7

c. RoutetheKeyboardCablethroughthechannelintheKeyboard

ShelfandtheninstallaStrainReliefBushing.

18526

Strain Relief Bushing



d. ProceedtoStep#6.

8 7401-K568

2336‐K212RuggedKeyboardw/Trackball

Note: The2336‐K212RuggedKeyboardrequirestheRugged

KeyboardMountkit(7402‐K569)inordertoinstallthekeyboardon

themount.Thiskitincludeseverythingshownbelowexceptthe

keyboard.

a. InserttheGasketintothebottomoftheRuggedKeyboard

Housing.

b. Insert

theRuggedKeyboardintothebottomoftheRugged

KeyboardHousing.

c. InstallthetwoRuggedKeyboardClamps(four nutseach).

Caution: Evenlytightenthenutsbeforeapplyingthefinal

torquetosecuretheRuggedKeyboardClamps.DONOTover

tightenthenutsasthiscandeformtheRuggedKeyboard

Housing.

22570b

Rugged Keyboard Clamp (2)

Rugged Keyboard

Gasket

Rugged Keyboard Housing

Nut, 6-32 Keep Lock (4)



7401-K568 9

d. InstalltheKeyboardAssemblyontotheKeyboardShelfand

secureitwithscrews(4).

22571

Keyboard Assembly

Keyboard Shelf



10 7401-K568

e. RoutetheKeyboardCablethroughthechannelintheKeyboard

ShelfandtheninstallaStrainReliefBushing.

18526

Strain Relief Bushing



7401-K568 11

6. RoutetheKeyboardCablethroughtheCableChainBracketand

thenconnecttheCableChainontotheCableChainBracket.

18527

Cable Chain Bracket

Cable Chain Bracket Screws



12 7401-K568

7. RouteKeyboardCablethroughthesplitsideoftheCable Chain

links.

18528

Push Cable Into Chain



7401-K568 13

8. ExtendtheMountingPlatefullyforward.

9. RoutetheKeyboardCablethroughtheMountingBracket.

10. SlidetheKeyboard ShelfontotheBottomPlateandinstallthefour

screws.

11. ConnecttheCableChaintotheCableChain Bracket.

18529

Cable Chain Bracket



14 7401-K568

12. InstallaStrainRelief BushingintheMountingBracket.

18530

Strain Relief

Bushing



7401-K568 15

Installing the Mounting Bracket

SecuretheMountingBrackettoawallwithlagscrewsorwith

hardwareofsimilarstrength.Therecommendedviewingheightforthe

terminalis1.2m(48ʺ)fromthefloor.

17351

Wall Bracket

Lag Screws (6)

1.2 m (48 in)

Recommended

Height from Floor



16 7401-K568

Installing the Fixed-Angle Mount

1. MatetheslotsinthebackoftheFixed‐AngleMountontothe

lockingtabsontheMountingBracket.

2. SecuretheFixed‐AngleMountwiththetwosuppliedscrews.

18531



NCR 7402-K568 Kit Instructions

NCR 7402-K568 Kit Instructions

NCR 7402-K568 Kit Instructions

Related papers

Other documents