Barco Fiberlink 2 Receiver single-mode Installation guide

Fiberlink 2

Owners manual

R5976861/03

18/11/2005

Barco nv Events

Noordl

aan 5, B-8520 Kuurne

Phone: +32 56.36.89.70

Fax: +32 56.36.88.24

E-mail:

[email protected]

Visit us at the web: www.barco.com

PrintedinBelgium

Changes

Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied war-

ranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the

program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this

publication; these changes are incorporated in new editions of this publication.

stored in a retrieval system without the prior written consent of Barco.

Federal Communications Commission (FCC Statement)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC r

ules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of t

his equipment in a residential area may

cause harmful interference, in which case the user will be responsible for correcting any interference.

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser

must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco

must be informed immediately in writing of any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,

at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement

at its own discretion within an appropriate period. If this measure proves t

o be impossible or unsuccessful, the purchaser can demand a

reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or

indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component

of the system or independent service, will be deemed invalid provided

the damage is not proven to be attributed to the absence of properties

guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly,

in particular if the systems are commissioned operated incorrectly or if, after the transfer of risks, the goods are subject to influences not

agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are

system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as

well as normal maintenance are not subject to the guarantee provided by Barco either.

The environmental conditions as well as the servicing a

nd maintenance regulations specified in the this manual must be complied with by

the customer.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.

All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for

the products or their manufactures.

Table of contents

TABLE OF CONTENTS

1. Safety.................................................................................................................. 3

1.1 Important safety instructions.......................................................................................................... 4

1.2 Important warnings.................................................................................................................... 5

2. General................................................................................................................ 7

2.1 Fiberlink 2 ............................................................................................................................. 8

2.2 Functionality........................................................................................................................... 9

3. System components...............................................................................................11

3.1 Base unit..............................................................................................................................12

3.2 Transmitters ..........................................................................................................................13

3.3 Receivers............................................................................................................................. 14

3.4 Optical fiber cables...................................................................................................................15

3.5 Power and data cables...............................................................................................................17

4. Installation...........................................................................................................19

4.1 Installing the Fiberlink 2 base unit...................................................................................................20

4.2 Installing the Fiberlink 2 receiver ....................................................................................................22

4.3 Other mounting positions of the Fiberlink 2 receiver. . . .............................................................................24

4.4 Full installation example .............................................................................................................25

5. User interface .......................................................................................................27

5.1 Main menu structure .................................................................................................................28

5.2 “Diagnostics” menu description......................................................................................................30

5.3 ”Pattern GEN” menu description.....................................................................................................33

5.4 “LED-wall” menu description.........................................................................................................35

5.5 “Ethernet conf” menu description....................................................................................................36

5.6 Fiberlink 2 messages (apart from menu messages) . . . .............................................................................37

6. Maintenance.........................................................................................................41

6.1 Diagnoses via TCP/IP. ...............................................................................................................42

6.2 Software update...................................................................................................................... 43

A. Dimensions ..........................................................................................................45

A.1 Dimensions of the Fiberlink 2 base unit .............................................................................................46

A.2 Dimensions of the Fiberlink 2 transmitter unit.......................................................................................47

A.3 Dimensions of the Fiberlink 2 receiver ..............................................................................................48

B. Specifications .......................................................................................................49

B.1 Fiberlink 2 specifications.............................................................................................................50

C. Order info ............................................................................................................51

C.1 Order info.............................................................................................................................52

Index......................................................................................................................53

R5976861 FIBERLINK 2 18/11/2005 1

Table of contents

2 R5976861 FIBERLINK 2 18/11/2005

1. Safety

1. SAFETY

About this chapter

Read this chapter attentively. It contains important safety information concerning product installation and usage. Furthermore, it

includes several cautions to prevent damage to the Fiberlink 2. Ensure you understand and follow all the safety guidelines, safety

instructions and warnings mentioned in this chapter before installing and using the Fiberlink 2 system. After this chapter additional

“warnings” and “cautions” are given depending on the installation or other procedures. Read and follow this “warnings” and “cautions”

as well.

Overview

• Important safety instructions

• Important warnings

R5976861 FIBERLINK 2 18/11/2005

3

1. Safety

1.1 Important safety instructions

Instructions:

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Clean only with materials or chemicals that are inert, nonabrasive, noncorrosive and non-marking. Consult the manufacturer

for further advice should any doubts exist regarding any cleaning procedure.

• Do not block ventilation openings. Install in accordance with the manufacturers instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that

produce heat.

• Do not defeat the safety purpose of the polarized or grounding type plugs/sockets. If the provided sockets/plugs are damaged

then replacement of the defective parts must be undertaken immediately.

• Protect the power/data cords from being walked on or pinched particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus. Replace damaged power/data cords immediately.

• Only use attachments/accessories specified by the manufacturer.

• Disconnect the power to this apparatus during lightning storms or provide suitable additional lightning protection. Unplug this

apparatus when unused for long period of time.

• Refer all servicing to qualified service technicians/personnel. Servicing is required when the apparatus has been damaged in

any way, such as power-supply cord or plug is damaged, the apparatus does not operate normally, or has been dropped.

• Use only with systems or peripherals specified by the manufacturer, or sold with the apparatus. Use ca

ution during lifting/moving

or transporting to avoid damage by possible tipping.

4

R5976861 FIBERLINK 2 18/11/2005

1. Safety

1.2 Important warnings

Important warnings

• Risk of electric shock:

Do not open. To reduce the risk of electric shock, do not remove cover (or back). No user-serviceable parts inside. Refer

servicing to qualified service personnel.

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

CAUTION

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with an arrowhead within a triangle is intended to tell the user that parts inside this product may cause a risk

of electrical shock to persons.

The exclamation point within a triangle is intended to tell the user that important oper

ating and/or servicing instructions are

included in the technical documentation for this equipment.

• Class 1 laser product:

The Fiberlink 2 does not produce laser radiation hazardous to the user. It is certified as a Class 1 laser product.

CLASS 1

LASER PRODUCT TO IEC 825

• Maximum and minimum ambient temperature:

The maximum ambient temperature for the Fiberlink 2 transmitter is 40 °C, the minimum temperature is 0 °C.

The maximum ambient temperature for the Fiberlink 2 receiver is 50 °C, the minimum temperature is -20 °C.

• Ventilation:

The Fiberlink 2 transmitter requires that air flows freely in both the front and rear ventilation holes. Blocking these holes will

greatly reduce the reliability of the unit an lead to the possibility of overheating.

The Fiberlink 2 receiver is equipped with external fans. Ensure that air can flows freely into the fans, otherwise the reliability of

the receiver will be reduced and the unit can be overheated.

• Flammable materials:

Keep flammable materials away from the installation (such a

s curtains). A lot of energy is transferred into heat. The installation

should be such that the amount of air flow required for safe operation of the equipment is not compromised. Proper ventilation

must be provided.

• This equipment MUST be earthed:

In order to protect against risk of electric shock, the installation should be properly grounded. Defeating the purpose of the

grounding type plug will expose you to the risk of electric shock.

• Power system:

It is recommended to use a TN-S power distribution system (a power distribution system with a separate neutral and grounding

conductor) in order to avoid large ground currents loops due to voltage differences in the neutral conductor. The total electrical

installation should be protected by an appropriate r

ated disconnect switch, circuit breakers and Ground Fault Current Inter-

rupters. The installation shall be done according to the local electrical installation codes. In Europe special attention should be

given to EN 60364, the standard for electrical installation of buildings. In Germany VDE 0100 should be adhered to.

• Disconnect device:

When the appliance inlets of the individual tiles are not accessible, the socket outlets supplying the rack shall be installed near

the equipment and be easily accessible, or a readily accessible general disconnect device shall be incorporated in the fixed

wiring.

• Mains cords:

The power cords delivered with this system have special properties for safety. They are not user serviceable. If the power cords

are damaged, replace only with new ones. Never

try to repair a power cord.

• Rack mounting:

When using Fiberlink 2 base unit (TX) in a multi rack assembly or closed assembly, the ambient temperature inside the assembly

may not exceed the maximum rated ambient temperature of the Fiberlink 2 transmitter, which is 40 °C.

When installed in a rack, the mounting should be such that no hazardous condition is achieved due to uneven mechanical

loading.

• Cabinet openings:

Never push objects of any kind into this product through cabinet slots as they may touch dangerous high voltage points or short

out parts that could result in a risk of fire or electrical shock.

Never spill liquid of any kind on the product.

Should any liquid or solid object fall into the cabinet, unplug the set and have it

checked by qualified service personnel before resuming operations.

R5976861 FIBERLINK 2 18/11/2005

5

1. Safety

• Replacement parts:

When replacement parts are required, be sure the service technician has used original Barco replacement parts or authorized

replacement parts which have the same characteristics as the Barco original part. Unauthorized substitutions may result in

degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty.

• Safety check:

Upon completion of any service or repairs to this device, ask the service technician to perform safety checks to determine that

the device is in proper operating condition.

6

R5976861 FIBERLINK 2 18/11/2005

2. General

2. GENERAL

About this chapter

This chapter contains general information about the Fiberlink 2 concept. Reading this chapter will helps you to identify the different

components of the Fiberlink 2 and understand the functionality of it, which will be a benefit during the installation.

Overview

• Fiberlink 2

• Functionality

R5976861 FIBERLINK 2 18/11/2005

7

2. General

2.1 Fiberlink 2

Introduction

The Fiberlink 2 is a bidirectional digital fiber optic transmission system between a Barco Digitizer and a Barco LED-wall. It covers

real long distances and has a very high bandwidth. This enables the end-user for instance to setup the Digitizer in a remote control

room. The Fiberlink 2 transmits not only the video signals but also the communication to the LED-wall. The Fiberlink 2 receiver is

sheltered in a compact IP65 housing which makes the receiver usable for indoor and outdoor LED-wall applications. An extensive

self-diagnose system has been implemented to display any transmission fault conditions should they arise.

Purpose

The Fiberlink 2 is used to achieve transmission distances of more than 100 meter and up to 5 kilometer between Digitizer

and

LED-wall.

Note that transmission distances shorter than 100 meter can be achieved by the “Compact link” (See installation manual of the

Compact link for more information).

Multi- or single- mode ?

The Fiberlink 2 transmitters and receivers are available in two types. For distances up to 500 me

ter the “multi mode” Fiberlink 2

transmitters and receivers are used. The optical fiber cable hereby used is a multi mode duplex 50/125 µm cable and the laser used

in transmitter and receiver (bidirectional) is a 850 nm VCSEL laser. Those transmitters and receivers have a grey colored housing

with a black colored print.

For distances longer than 500 meter you require a Fiberlink 2 Long Distance (LD) transmitter and receiver with “single mode” optical

fiber technology. The optical fiber cable hereby used is a single mode duplex 9/125 µm cable and the laser used in transmitter and

receiver (bidirectional) is a 1300 nm FP laser. Those transmitters and receivers are marked with the text “LD” or “Long Distance”

and have a black colored housing with a grey colored print.

Multi mode fiber cables can not be used in combination with a single mode (LD) transmitter nor receiver unit,

neither can single mode fiber cables be used in combination with a multi mode transmitter nor receiver unit.

8 R5976861 FIBERLINK 2 18/11/2005

2. General

2.2 Functionality

System overview

The Fiberlink 2 system is inserted in the data path between the Digitizer and the first tile of the LED-display. One Fiberlink 2 system

can handle up to 3 digitizers. Per Digitizer a Fiberlink 2 transmitter unit is inserted into the Fiberlink 2 base unit. The Fiberlink 2

base unit, containing the transmitter unit(s), is installed in the same rack of the Digitizer(s). Each transmitter unit is connected with

a fiber optic cable to a Fiberlink 2 receiver unit, which is installed nearby the first tile in the LED-display.

Diagram

LED-wall

Input 1

Input 2

Input 4

SLOT 2

TX

SLOT 1 SLOT 3

TX

Fiberlink 2

Digitizer

SLOT 1

INPUT

SLOT 2

INPUT

SLOT 3 SLOT 4

INPUT

RX

B

A

D

E

C

F

Image 2-1

A Digitizer input module.

B DVI cable (R9851211).

C Fiberlink 2 transmitter unit.

D Fiber optic cable.

E Fiberlink 2 receiver unit.

F Data cable to first tile in display.

R5976861 FIBERLINK 2 18/11/2005

9

2. General

10 R5976861 FIBERLINK 2 18/11/2005

3. System components

3. SYSTEM COMPONENTS

About this chapter

This chapter describes the different components of the Fiberlink 2 system.

Overview

•Baseunit

• Transmitters

• Receivers

• Optical fiber cables

• Power and data cables

R5976861 FIBERLINK 2 18/11/2005

11

3. System components

3.1 Base unit

Introduction

The cabinet of the Fiberlink 2 base unit fits in a standard 19” rack (482,6 mm) and has a height of 1U (44 mm). Up to three transmitter

units can be inserted into the slots at the rear of the base unit. Each transmitter unit adds a fiber channel to the system. The front

of the base unit contains a jog dial and three LCD displays, one per input slot. This jog dial (thumb wheel) allows you to enter the

user interface for configuration and diagnostic purposes on each inserted transmitter unit and/or connected receiver unit.

The Fiberlink 2 base unit has an auto ranging power supply between 90 and 132 volt and between 180 and 264 volt (50-60 Hz),

which provide power to the local control board and the inserted transmitter units. Futhermore, the base unit is equippe

d with several

small fans that improve the internal airflow to control the heat dissipation. Cool air flows into the base unit cabinet at the front, flows

trough the transmitter units (slots) and leaves at the rear.

The rear of the Fiberlink 2 base unit contains an USB and TCP/IP port, which allows software updates and diagnostic via network.

Image 3-1

Connector sockets and input slots of the Fiberlink 2 base unit

A B C D E F G

SLOT 3 SLOT

2

SLOT 1

Image 3-2

A Mains power input.

B Power ON/OFF switch.

C TCP/IP port for runtime diagnostics information.

D USB port (field upgrade purposes).

E DVI input port of the transmitter unit, which is inserted in SLOT 3.

F Optical output socket (LEMO connector, connection with receiver unit).

G Dummy cover plate.

12

R5976861 FIBERLINK 2 18/11/2005

3. System components

3.2 Transmitters

Introduction

The Fiberlink 2 transmitter unit has a DVI-D input, supports dual path graphics data rate (64 MHz pixel rate) and causes no frame

delay. The optical transceiver is equipped with a robust LEMO® connector. Futhermore, the transmitter has an internal pattern

generator, a build in fiber test (ping) and supports RS422 communication up to 115200 baud.

The Fiberlink 2 transmitter is available in two types, the short distance module “FIBERLINK” (maximum 500 meter) and the long

distance module “FIBERLINK LD” (up to 5 kilometer). The short distance module has a grey colored background with a black colored

print. The long distance module has a black colored background and a grey colored print.

Image 3-3

The Fiberlink 2 base unit accepts both types of transmitter units even

in a mixed combination (e.g. two short

distance modules and one long distance module).

Always use the transmitter unit in combination with the same type of receiver unit.

R5976861 FIBERLINK 2 18/11/2005 13

3. System components

3.3 Receivers

Introduction

The Fiberlink 2 receiver is sheltered in a compact IP65 housing which makes the receiver usable for indoor and outdoor LED-wall

applications. This single fiber channel device has a robust optical LEMO® connector and standard Barco outdoor connector sockets.

To energize the receiver unit, which is auto ranging between 190 and 264 volt (50-60 Hz), the unit is electrical connected in the power

path of the tiles in the LED display. Futhermore, the receiver has an internal pattern generator, a build in fiber test (ping) and supports

RS422 communication up to 115200 baud.

Just like the Fiberlink 2 transmitter the receiver is also available in two types, the short distance module “FIBERLINK

” (maximum

500 meter) and the long distance module “FIBERLINK LONG DISTANCE” (up to 5 kilometer). The short distance module has a grey

colored background with a black colored print. The long distance module has a black colored background and a grey colored print.

The receiver unit can be upgraded in the field over fiber while operating (if connected to a transmitter unit) or via USB cable by

removing the dummy input.

Image 3-4

Mounting plate and connector sockets of a Fiberlink 2 receiver

To facilitate the physical installation of the Fiberlink 2 receiver, the receiver is equipped with a mounting plate containing several

mounting holes. With hammer bolts, included in the sy

stem, the receiver can easily be mounted against the rear of a Barco LED-wall

supporting structure.

Barco uses special designed sockets for outdoor power and data connections from tile to tile and to other peripherals like the Fiber-

link 2 receiver. These rugged sockets are watertight (IP65) when used with the appropriate plugs and sealing rings. Each socket is

equipped with a plug holder clamp which, when locked, ensure that the plug is completely pressed into the socket.

G

F

A

D

E

C

B

H

Image 3-5

A Optical input (LEMO connector, connection with Fiberlink 2 transmitter unit).

B Power input socket.

C Power output socket.

D Data output socket (connection with first tile in the LED-wall).

E Socket cover for USB port (field upgrade purposes).

F External fans.

G Mounting plate.

H Plug holder clamp.

14

R5976861 FIBERLINK 2 18/11/2005

3. System components

3.4 Optical fiber cables

Introduction

The optical fiber cable, used between the Fiberlink 2 transmitter and receiver, can be installed by a third party, specialized in optical

fiber installations. When realizing the fiber channel yourself take into account the fragility of the fiber cable. Note that the place-

ment of optical fiber cables are subject to special installation instructions enforced by the fiber cable manufacturer. Some general

instructions are:

• Never bend the optical fiber cable too sharp.

• Always use a bend radius of at least 10 centimeter.

• Place the fiber cable into a cable guard.

Barco offers two types of fiber optic cables. The multi mode (MM) fiber optic cable and the single mode (SM) fiber optic cable. B

oth

types are equipped with robust optical LEMO® plugs and are available in different lengths, see chapter “Order info”.

Image 3-6

Optical fiber cable with LEMO® plugs.

Always use a single mode fiber optic cable (SM) with a long distance (LD) transmitter and receiver unit and a

multi mode fiber optic cable (MM) with a short distance transmi

tter and receiver unit.

To protect the fiber entrance place the protective cap upon the LEMO® plug in case the plug is not inserted

into a peripheral. Align the red dot on the cap with the red dot on the plug and then push the cap over the

plug until an audible click ensure that the plug is well inserted.

Which optical fiber cable to use ?

The Fiberlink 2 requires optical fiber cables with a minimum bandwidth depending on the length of the fiber channel. Consult the

table below to choose the correct fiber cable for your Fiberlink 2 system.

Length fiber channel

Fiber type

Minimum bandwidth of fiber

0-300meter

Multi mode fiber

500 MHz.km

300 - 500 meter

Multi mode fiber

2000 MHz.km

500 - 5000 meter

Single mode fiber

—

Pre-installed optical fiber network

The Fiberlink 2 can make use of a pre-installed (permanent) network of optical fiber cables. Those pre-installed fibers starts and

ends in p

atch panels provided with industrial standard optical connector sockets like ST or SC, which can be connected with a (short)

optical fiber cable and adapted plugs to the desired peripherals. Note that, next to the length, each connection in the path of the

fiber channel causes a little decrease of the signal power. The two illustrations below show adapted optical fiber cables, to connect

the F

iberlink 2 transmitter with the patch panel of the optical fiber network.

R5976861 FIBERLINK 2 18/11/2005

15

3. System components

Image 3-7

Short optical fiber cable with LEMO® plug and SC

connectors.

Image 3-8

Short optical fiber cable with LEMO® plug and ST

connectors.

16 R5976861 FIBERLINK 2 18/11/2005

Page is loading ...

Barco Fiberlink 2 Receiver single-mode Installation guide

This manual is also suitable for

Barco Fiberlink 2 Receiver single-mode Installation guide

Related papers

Other documents