Rugged Ridge 18003.42 Installation guide

Brand
Rugged Ridge
Model
18003.42
Type
Installation guide

Rugged Ridge 18003.42 is a Jeep Wrangler Evaporator Skid Plate designed to protect the vehicle's evaporator canister and bracket from damage caused by rocks and other road hazards. It is made of durable steel and features a black powder-coat finish for corrosion resistance. The skid plate is easy to install with no drilling required, and it fits both 2-door and 4-door Jeep Wranglers with a 3.6L V6 engine manufactured between 2012 and the present. The skid plate is designed to work with factory CV-type drive shafts and most aftermarket U-joint replacement shafts.

Rugged Ridge 18003.42 is a Jeep Wrangler Evaporator Skid Plate designed to protect the vehicle's evaporator canister and bracket from damage caused by rocks and other road hazards. It is made of durable steel and features a black powder-coat finish for corrosion resistance. The skid plate is easy to install with no drilling required, and it fits both 2-door and 4-door Jeep Wranglers with a 3.6L V6 engine manufactured between 2012 and the present. The skid plate is designed to work with factory CV-type drive shafts and most aftermarket U-joint replacement shafts.

18003.42 Jeep Wrangler Evaporator Skid Plate
2012 - Present, 2DR - 4DR (3.6L V6)
JK Wrangler Evaporator Skid Plate Installation Instructions 2012 - Up
(1) Rear cross member mounting bracket
(1) Middle cross member mounting bracket
(1) Skid plate
(2) M10 Hex head bolt
(2) M10 Flat washer
(2) M10 Counter sunk bolts
Step 1. Please read instructions fully prior to installing the JK Evaporator Skid Plates (18003.42).
The Skid Plate has been designed to be a no drill application for ease of installation. Take
your time when installing to insure proper fitment and tightening of bolts.
PLEASE NOTE: This kit has been designed to work with factory drive shafts and most
aftermarket U-Joint style drive shafts. It is the installers responsibility
to check for proper clearance of drive shaft to skid plate before vehicle
is operated. 2dr JK suspension should be cycled to make sure aftermarket
rear drive shaft yoke does not make contact with skid plate or mounting
bracket.
(18003.42) Rev.1 12/14/11
Step 2. Put vehicle in 1st gear or Park (Automatics), set emergency brake and block tires before proceeding
with installation.
Step 3. Disconnect vapor canister sensors wire connection. Set wire connection out of the way of cross
member (Pic.1).
Pic.1
Step 4. Remove rear 5/8” factor bracket retainer bolt. Do not discard bolt. Factory bolt will be used later to
install Evaporator Skip Plate (Pic.2).
Step 5. Remove (2) front 5.8” bracket retainer bolts. Do not discard bolts. Factory bolts will be reused to
install Evaporator Skid Plate. (Pic.3)
Step 6. Carefully allow the evaporator canister and bracket to drop away from vehicle. DO NOT disconnect
any vapor lines (Pic.4).
Pic.2 Pic.3 Pic.4
Page 1 of 2
18003.42 Jeep Wrangler Evaporator Skid Plate
2012 - Present, 2DR - 4DR (3.6L V6)
JK Wrangler Evaporator Skid Plate Installation Instructions 2012 - Up
(18003.42) Rev.1 12/14/11
Step 7. Place rear cross member mounting bracket onto factory metal evaporator retainer bracket as shown.
Bracket mounting hole should line up with factory mounting hole of retainer bracket (Pic.5).
Step 8. Place middle cross member mounting bracket (slotted hole) over cross member mounting holes.
Raise factory retainer bracket and vapor canister and hand start 5/8” bolts removed in step 3.
Do not tighten at this time. Allow mounting bracket to slide for alignment (Pic. 6).
Pic.5
Step 9. Raise rear retainer bracket with new mounting bracket to cross member and install 5/8” bolt removed
in step 4. Do not tighten at this time. Allow mounting bracket to move for alignment (Pic.7).
Reconnect sensor wire at this time (Pic.1 - Step 3)
Step10. Install skid plate to mounting brackets using M10 hardware supplied. Do not tighten at this time.
Move skid plate as needed to clear resonator and drive shaft (Pic. 8 & 9).
Pic.6 Pic.7 Pic.8
Page 2 of 2
Pic.9 Pic.10 Pic.11 Pic.12
Step11. With skid plate located, mark position of front mounting bracket (Pic.10). Remove skid plate and
tighten front (2) 5/8” bolts. Reinstall skid plate and double check position.
Step12. With skid plate mounted tighten rear 5/8” bolt and all M10 supplied hardware (Pic.11).
Step13. Inspect skid plate to make sure it clears both the exhaust and rear drive shaft (Pic.12).
Step14. Please Note: this product has been designed to work with factory CV type drive shafts and most
aftermarket U-Joint replacement shafts. 2dr JK Wranglers should have the rear suspension cycled
to insure no contact is made with skid plate and aftermarket rear drive shaft.
  • Page 1 1
  • Page 2 2

Rugged Ridge 18003.42 Installation guide

Brand
Rugged Ridge
Model
18003.42
Type
Installation guide

Rugged Ridge 18003.42 is a Jeep Wrangler Evaporator Skid Plate designed to protect the vehicle's evaporator canister and bracket from damage caused by rocks and other road hazards. It is made of durable steel and features a black powder-coat finish for corrosion resistance. The skid plate is easy to install with no drilling required, and it fits both 2-door and 4-door Jeep Wranglers with a 3.6L V6 engine manufactured between 2012 and the present. The skid plate is designed to work with factory CV-type drive shafts and most aftermarket U-joint replacement shafts.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents