Page is loading ...
PACK 19PACK 19
STAGE PAGE
91 Port wing ribs 218
92 Port wing ribs 220
93 Port wing leading edge 222
94 The port wing 224
95 Pylons 227
Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.
Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.
All rights reserved © 2019
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
218
Stage 91: Port wing ribs
Your parts
1. P235 - Rib
2. P236 - Rib
3. P237 - Rib
Assembly
1 Prepare the port wing assembly from the previous stage. Install rib (P235) over the spars in the next available slots
in the frame.
D096
P235
P235
P236
P237
219
2 Then install the next rib (P236) in the next slot.
3 Install rib (P237) in the next slot along in the port wing frame.
D096
D096
P236
P237
220
Stage 92: Port wing ribs
Your parts
1. P238 - Rib
2. P239 - Rib
3. P240 - Rib
4. X020 - Port
navigation light
Assembly
1 Prepare the port wing frame. Fit the rib (P238) into
the next available slots in the port wing frame. 2 Install rib (P239) on the port wing frame.
P238
P239
D096 D096
P238 P239 P240
X020
221
3 Then install
the final rib
(P240) into
the remaining
slots in the
wing frame.
4 Insert the end
of the port
navigation light
into the socket
labelled C, as
shown. Turn
on the power
supply and
check that the
light illuminates.
5 Then disconnect
the wires and
keep the light
to one side.
P240
D096
P240P239P238
222
Stage 93: Port wing
leading edge
Your parts
1. Р241 - Port wing leading edge upper half
2. Р242 - Port wing leading edge lower half
LP and OP screws
P241
P242
LP OP
223
Assembly
1 Combine the upper and lower halves of the port wing leading edge (P241 and P242). Fix the halves together with
four LP screws.
2 Fix the narrow end together with an OP screw.
P242
P242
P241
P241
224
Stage 94: The port wing
Your parts
1. Р243 - Port wing upper panel
2. Р244 - Port wing lower tip
3.X025 - Adhesive tape
SM screws
NP screws
LP screws
Assembly
1 You will need the parts supplied with this stage, part X020 from
Stage 92, as well as assemblies from Stages 92 and 93. Bend the port
navigation light wire as shown.
2 Then pass
the light wire
along the
port wing
and use the
adhesive
tape to hold
it in place,
as shown.
X020
D096 X020 X025 X025 X025
P243
X025
P244
SM NP LP
225
3 Fit the port wing
leading edge
assembly onto
the front of the
wing frame.
4 Then place
the port wing
upper wing
panel (P243)
onto the frame.
5 Check that the
wire is placed in
the grooves in
the ribs.
D096
D096 P243
P241
226
D096
D096
P244
6 Fix the panel
from the
underside of the
frame with eight
NP screws.
7 Then tighten an
LP screw into
the indicated
hole.
8 Install the port
wing lower
tip (P244) at
the edge of
the wing and
secure with
two SM screws.
227
Stage 95: Pylons
Your parts
1.D100 - Pylons (3 pcs.)
2. P250 - Tabs (6 pcs.)
MM screws
D100
P250
MM
228
D100
D100
D100
P250
P250
P250
P250
P250
P250
Assembly
2 Secure the tabs to the pylons with MM screws.
1 Place all of the tabs (P250) into the spaces in the pylons (D100), as shown.
/
