Page is loading ...
1. Functions of the
WindGuide Plus
The basic functions of the
WindGuide Plus are
measurements of Wind (Air)
Speed, Temperature, Wind Chill
Factor, Humidity, Barometric
Pressure and Altitude. You can
also check the Date and Time
and choose HOLD, MAX or MIN
for the measurement functions.
A Backlight feature can be used
in the dark and an Auto Off fea-
ture is standard.
2. Initial Set Up
To activate open battery door
and pull the tab out. Replace
door and turn power off.
While the unit is off, press
and hold down (for a few sec-
onds) and press to enter the
mode of your initialization set-
tings.
2.1 Set the Date and Time
Date display = Day: Month: Year
(e.g., 25:10:12)
Time display = Hour: Minute:
Second (e.g.,23:35:45)
First set the date – a default
date will display on the screen. Press to adjust the day, and press
to confirm after each adjustment – day/month/year.
After the date is set, the unit automatically goes to the Time setting.
Note: The time display is only available in a 24 hour format. Set the
hour/minutes/seconds using the button, and press to confirm after
each setting.
2.2 Set Wind/Air speed units = m/s (meters per second), mph (miles
per hour), fps (feet per second), km/h (kilometers per hour), knots –
wind conversions readily available on the Internet
The default is m/s. Press to find the desired unit and press to
confirm.
2.3 Set the Temperature unit setting of ºC or ºF. Press to find the
desired unit and press to confirm
2.4 Set Humidity = the humidity is a fixed measurement showing per-
centage of relative humidity. Press to proceed to the next setting
2.5 Set Barometer units = barometric pressure can be measured with
inHg (inches of
mercury) or hPa (hectopascals). Press to find the desired unit and
press to confirm
2.6 Set Altitude = choose m (meters) or ft (feet). Press to find the
desired unit and press to confirm.
The WindGuide Plus turns off automatically after all the settings are com-
plete.
The settings you have made will remain valid until you change the
settings or the battery is replaced. When replacing the battery, you will
have to reset all the settings.
3. Operating the WindGuide Plus
After the Initial Set Up is complete, you can now operate the WindGuide
Plus.
3.1 Press to switch the unit on
3.2 Display a desired function
Press for 3 seconds to choose from Wind/Air Speed Temperature
Wind Chill (the felt air temperature on exposed skin due to the
wind) Humidity. Press repeatedly until the desired function dis-
plays on the LCD screen.
Press for 3 seconds to choose from Time Barometric Pressure
Altitude. Press repeatedly until the desired
function displays on the LCD screen.
3.3 Hold the current reading and display the MAX and MIN value.
Hold the current reading at any time by pressing . Press again to
display the MAX and MIN value since the unit was turned on.
Note: The MAX and MIN values will not be kept in the unit’s memory
once it goes off.
3.4 Date – can be seen momentarily when turning the unit on
3.5 Backlight
Press and at the same time for 3 seconds to turn the backlight on.
It will shut off automatically after 20 seconds.
3.6 Turn the unit off
Auto Shut Off = the unit goes off automatically after
5 minutes idle.
Manually = Press and at the same time for 6 seconds.
4. Specifications
Wind/Air Speed = up to 108 km/h or 67 mph;
30 ms or 98 fps or 58 knots Temperature = -10~60ºC / 14~140ºF
Humidity = 5%~95%RH (Relative Humidity)
Barometric Pressure = 300 to 1200 hPa /inHg 8.9 to 34.5
INSTRUCTION MANUAL
MODELS
#48025
AND #48026
Altitude = -500 to 9000 m (meters) / -1600 to 29,500 ft (feet)
Power Supply = 1x3.0V CR2032 Battery – average life 75 hours of continuous usage.
Current consumption approximately 3mA.
Impeller/Fan/Vane = 14.2 mm / 0.6”
(not removable or replaceable)
Size = 47.5x123x18 mm / 1.9x4.8x0.7 inches
Weight = 45 g / 1.6 oz
Weather Resistant
5. Battery
The condition of the CR2032 battery is shown on the top left of the LCD screen when getting low. To change the battery, use a coin (or small
slotted tool) to remove the battery cover and change the battery with the “+” facing you. Put the battery door back on.
WWW.CELESTRON.COM
Your Celestron WindGuide Plus has a Two Year Limited Warranty.
FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
This product is designed and intended for those 13 years of age and older.
Product design and specifications are subject to change without prior notification.
©2012 Celestron
All rights reserved
2835 Columbia Street, Torrance, CA 90503 U.S.A.
Telephone: 310.328.9560 • Fax: 310.212.5835
0412 Printed in China
/
