ADLINK Technology M-322 User manual

Category
Motherboards
Type
User manual
Advance Technologies; Automate the World.
Manual Rev.: 2.01
Revision Date: September 27, 2010
Part No: 50-1Z052-1010
M-322
ATX Industrial Motherboard with
Intel® Q35 Chipset
User’s Manual
Revision History
Revision Release Date Description of Change(s)
2.00 2010/06/23 Initial Release
2.01 2010/09/27 Correct System Panel Pin Header drawing
Preface iii
M-322
Preface
Copyright 2010 ADLINK Technology Inc.
This document contains proprietary information protected by copy-
right. All rights are reserved. No part of this manual may be repro-
duced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, spe-
cial, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the Euro-
pean Union's Restriction of Hazardous Substances (RoHS) direc-
tive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manu-
facturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification pur-
poses only and may be trademarks and/or registered trademarks
of their respective companies.
iv Preface
Using this Manual
Audience and Scope
The M-322 User’s Manual is intended for hardware technicians
and systems operators with knowledge of installing, configuring
and operating industrial grade computers.
Manual Organization
This manual is organized as follows:
Preface: Presents copyright notifications, disclaimers, trade-
marks, and associated information on the proper usage of this
document and its associated product(s).
Chapter 1, Introduction: Introduces the M-322, its features,
applications, and specifications, including functional descriptions
and board layout.
Chapter 2, Connectors & Jumpers: Provides technical informa-
tion on connectors, jumpers and pin assignments for configuring
the M-322.
Chapter 3, Getting Started: Describes how to install components
and drivers on the M-322.
Chapter 4, BIOS Setup: Presents information aid in configuring
the system BIOS.
Appendix A, Watchdog Timer: Presents information on under-
standing and configuring the watchdog timer.
Appendix B, System Resources: Presents information on I/O
mapping, IRQ routing, and resource allocation.
Important Safety Instructions: Presents safety instructions all
users must follow for the proper setup, installation and usage of
equipment and/or software.
Getting Service: Contact information for ADLINK’s worldwide
offices.
Preface v
M-322
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
NOTE:
NOTE:
Additional information, aids, and tips that help users perform
tasks.
CAUTION:
Information to prevent minor physical injury, component dam-
age, data loss, and/or program corruption when trying to com-
plete a task.
WARNING:
Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.
vi Preface
This page intentionally left blank.
Table of Contents vii
M-322
Table of Contents
Revision History...................................................................... ii
Preface.................................................................................... iii
List of Figures........................................................................ xi
List of Tables........................................................................ xiii
1 Introduction ........................................................................ 1
1.1 Package Contents ............................................................... 1
1.2 Overview.............................................................................. 2
1.3 Features............................................................................... 2
1.4 Specifications....................................................................... 3
1.5 Power Consumption ............................................................ 5
1.6 Block Diagram ..................................................................... 6
1.7 Functional Description ......................................................... 7
1.8 Board Layout ....................................................................... 9
1.9 Mechanical Drawings......................................................... 11
2 Connectors & Jumpers.................................................... 13
2.1 Rear I/O Connectors.......................................................... 13
2.2 Onboard Connectors ......................................................... 17
2.3 Jumpers............................................................................. 24
3 Getting Started ................................................................. 27
3.1 Installing the CPU.............................................................. 27
3.2 Installing the CPU Fan and Heatsink................................. 31
3.3 System Memory................................................................. 32
3.4 Driver Installation............................................................... 34
viii Table of Contents
4 BIOS Setup........................................................................ 37
4.1 Starting the BIOS............................................................... 37
4.2 Main Setup......................................................................... 41
4.3 Advanced Setings.............................................................. 45
4.3.1 USB Configuration.........................................................46
4.3.2 Trusted Computing ........................................................48
4.3.3 Intel TXT (LT) Configuration ..........................................49
4.3.4 Intel VT-d Configuration.................................................49
4.3.5 CPU Configuration.........................................................50
4.3.6 Chipset Settings.............................................................52
4.3.7 Onboard Device Configuration ......................................54
4.3.8 PCI/PnP Settings...........................................................55
4.4 Power Settings................................................................... 56
4.4.1 APM Configuration.........................................................58
4.4.2 Hardware Health Configuration .....................................59
4.5 Boot Settings ..................................................................... 60
4.5.1 Boot Device Priority.......................................................60
4.5.2 Boot Device Groups.......................................................60
4.5.3 Boot Settings Configuration...........................................61
4.5.4 Security..........................................................................62
4.6 Exit Menu........................................................................... 63
A Appendix: Watchdog Timer..............................................65
A.1 Sample Code..................................................................... 65
B Appendix: System Resources..........................................67
B.1 System Memory Map......................................................... 67
B.2 Direct Memory Access Channels....................................... 68
B.3 Fixed I/O Map .................................................................... 69
B.4 Variable I/O Map................................................................ 71
B.5 Interrupt Request (IRQ) Lines............................................ 72
B.6 PCI Configuration Space Map ........................................... 75
B.7 PCI Interrupt Routing Map................................................. 76
Table of Contents ix
M-322
Important Safety Instructions.............................................. 77
Getting Service...................................................................... 79
xTable of Contents
This page intentionally left blank.
List of Figures xi
M-322
List of Figures
Figure 1-1: M-322 Block Diagram......................................................6
Figure 1-2: M-322 Board Layout........................................................9
Figure 1-3: M-322 Rear I/O Layout..................................................10
Figure 1-4: M-322 Board Dimensions..............................................11
Figure 1-5: M-322 I/O Shield Dimensions........................................12
xii List of Figures
This page intentionally left blank.
List of Tables xiii
M-322
List of Tables
Table 1-1: M-322 General Specifications..........................................4
Table 1-2: M-322 Board Layout Legend.........................................10
Table 2-1: COM Serial Port Connector Pin Definition.....................14
Table B-1: System Memory Map.....................................................67
Table B-2: Direct Memory Access Channels...................................68
Table B-3: Fixed I/O Map................................................................70
Table B-4: Variable I/O Map............................................................71
Table B-5: IRQ Lines PIC Mode......................................................72
Table B-6: IRQ Lines APIC Mode ...................................................74
Table B-7: PCI Configuration Space Map.......................................75
Table B-8: PCI Interrupt Routing Map.............................................76
xiv List of Tables
This page intentionally left blank.
Introduction 1
M-322
1 Introduction
This chapter will introduce the M-322, its features, specifications,
functional description, and mechanical layout.
1.1 Package Contents
Please check that your package contains the items below. If
you discover damaged or missing items, please contact your
vendor.
X M-322 Industrial ATX Motherboard
X I/O shield
X 2x SATA data cables
X 2x SATA power cables
X 1x single COM port cable with bracket
X 1x dual COM port cable with bracket
X Driver DVD
X User’s Manual
WARNING:
DO NOT install or apply power to equipment that is damaged
or if there is missing/incomplete equipment. Retain the ship-
ping carton and packing materials for inspection. Please con-
tact your ADLINK dealer/vendor immediately for assistance.
Obtain authorization from your dealer before returning any
product to ADLINK.
2Introduction
1.2 Overview
The ADLINK M-322 is an ATX industrial motherboard supporting
the next-generation Intel® Core™2 Quad/Duo, Pentium® Dual
Core and Celeron® processors in the LGA775 package to deliver
a high performance platform for a wide array of industrial applica-
tions. The M-322 supports processing speeds up to 3.00GHz and
1333 MHz Front Side Bus (FSB). Dual channel DDR2
667/800 MHz memory is supported up to a maximum of 8GB in
four DIMM slots. The M-322 supports a broad range of processor
frequencies, high-speed data transfer rates, diverse I/O functions,
and high-bandwidth network connectivity.
These advanced features, coupled with integrated graphics, one
PCI Express® x16 slot, one PCI Express® x1 slot, five PCI slots,
and audio interfaces make the M-322 suitable for automation con-
trol, medical, test & measurement, and telecom applications
requiring an easy-to-deploy and reliable mainboard.
1.3 Features
X ATX form factor (305 mm x 244 mm)
X Supports Intel® Core™2 Quad/Duo, Pentium® Dual Core
and Celeron® processors in LGA775 package
X Dual 10/100/1000Mbps Ethernet
X 12x USB 2.0 ports (4x faceplate, 8x onboard pin header)
X 6x SATA 3 Gbps ports support RAID 0/1/5/10
X Integrated graphic supports VGA up to 2048 x 1536 @ 75Hz
X One PCIe x16 slot, one PCIe x1 slot, five PCI slots
X Watchdog Timer, Hardware Monitor
X Realtek ALC888 HD audio codec
X TPM hardware security chip
X RoHS compliant
Introduction 3
M-322
1.4 Specifications
System
CPU/Cache • IIntel® Core™2 Quad Q9400, 2.66GHz, 1333MHz FSB,
6MB L2 Cache, 45nm, 95W TDP
• Intel® Core™2 Duo E8400, 3.0GHz, 1333MHz FSB,
6MB L2 Cache, 45nm, 65W TDP
• Intel® Core™2 Duo E7400, 2.8GHz, 1066MHz FSB,
3MB L2 Cache, 45nm, 65W TDP
• Intel® Core™2 Duo E6400, 2.13GHz, 1066MHz FSB,
2MB L2 Cache, 65nm, 65W TDP
• Intel® Core™2 Duo E4300, 1.8GHz, 800MHz FSB,
2MB L2 Cache, 65nm, 65W TDP
• Intel® Pentium® Dual Core E5300, 2.6GHz, 800MHz FSB,
2MB L2 Cache, 45nm, 65W TDP
• Intel® Pentium® Dual Core E2160, 1.8GHz, 800MHz FSB,
1MB L2 Cache, 65nm, 65W TDP
• Intel® Celeron® 440, 2.0GHz, 800MHz FSB,
512KB L2 Cache, 65nm, 35W TDP
FSB • 800/1066/1333 MHz
Chipset • Intel® Q35 + ICH9DO
Memory • Four 240-pin DIMM sockets
• Dual-Channel DDR2 667/800MHz, up to 8GB
BIOS • AMI BIOS with 32 Mb Flash ROM
TPM • Infineon SLB 9635 TT 1.2
Audio • Realtek ALC888 HD codec
• Supports line-in, line-out and mic-in
Watchdog Timer • 1-255 second/minute programmable
Hardware Monitor • CPU/System temperature, fan speed and onboard DC
voltages
Operating System • Windows XP 32/64-bit edition
• Windows Vista 32-bit edition
• Windows Server 2008 32-bit edition
• Windows 7 32/64-bit edition
• Fedora 12
4Introduction
Table 1-1: M-322 General Specifications
I/O Interfaces
Serial ATA • 6x Serial ATA ports with 300 MB/s data transfer
• Supports RAID 0/1/5/10
Onboard I/O • 4x USB 2.0 pin headers (8 ports)
• 2x RS-232 serial port pin headers (COM2-3)
• 1x RS-232/422/485 serial port (COM4)
• 1 printer port
• 1x floppy port
• 1x front panel pin header
Rear I/O • 2x RJ-45 LAN port
• 4x USB 2.0 ports
• 1x D-Sub VGA connector
• 1x DB-9 RS-232 (COM1)
• 2x PS2 keyboard/mouse ports
• 3x audio jacks (line-in, line-out and mic-in)
Expansion Slots • 1x PCIe x16 slot
• 1x PCIe x1 slot
• 5x PCI slots
Display
Graphics • GMA 3100 integrated in Q35 GMCH
VRAM • Shared system memory up to 256 MB
VGA • Dsub-15 connector, up to 2048x1536 @ 75 Hz
Ethernet
Controller • Dual Realtek® RTL8111C PCIe network controllers
• 10/100/1000Base-T dual-Gigabit Ethernet
• Wake on LAN, PXE supported
Ports • 2x RJ-45 Ethernet port
Mechanical and Environment
Form Factor • ATX Industrial Motherboard
Dimensions • 305 mm x 244 mm (L x W)
Operating Temp. • 0°C to 60°C
Storage Temp. • -20ºC to 80ºC
Rel. Humidity • 10 - 90% non-condensing
Safety • CE, FCC Class A
Introduction 5
M-322
1.5 Power Consumption
Intel® Core™2 Duo Processor E6400
Test Configuration
CPU Intel® Core™2 Duo Processor E6400 2.13 GHz
Memory ADATA DDR2 667 1G (AD2667001GOU) x1
Graphics Intel ® Q35 Graphics Memory Controller Hub
Hard Drive Seagate Barracuda 7200.10 160GB ST3160815AS
Power Supply Delta 400W, GPS-400AB C Rev. 00F
Power On Boot Sequence
Power Req. +5V +3.3V +12V 5VSB Total
Current 2.12 A 2.14 A 2.84 A 0.62 A —
Power — — — — 54.84 W
Windows XP, Idle
Power Req. +5V +3.3V +12V 5VSB Total
Current 1.64 A 2.08 A 1.16 A 0.59 A —
Power — — — — 31.93 W
Windows XP, Maxpower 100% + 3DMark 2006
Power Req. +5V +3.3V +12V 5VSB Total
Current 2.04 A 2.10 A 2.88 A 0.59 A —
Power — — — — 54.64 W
6Introduction
1.6 Block Diagram
Figure 1-1: M-322 Block Diagram
Southbridge
Intel
®
ICH9DO
CPU
Coreâ„¢2 Quad/Duo
Pentium
®
Dual Core
Celeron
®
LGA775 package
Northbridge
Intel
®
Q35 GMCH
DMI
Interface
2 GB/s
LPC
USB 2.0
SPI BIOS
KB/Mouse
LPT/FDD
1x RS-232/422/485
3x RS-232
CRT
DB-15
Winbond
83627 DHG-A
Super I/O
12x USB 2.0
(4x Bracket, 8x Internal)
800/1066/1333 MHz
FSB
Channel A
Channel B
DDR2 667/800 MHz
PCIe
Controller
P
C
I
e
x
1
PCI Bus
PCI
32-bit/33MHz bus
SATA
6x SATA ports
JMicron JMB368
PCIe to PATA controller
4x DIMM
Realtek
ALC888
HD
Codec
PCI
Controller
2x RTL8111C
PCIe GbE
TPM
SPI
PCIe x16 slot
P
C
I
e
x
1
PCI Express x1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94

ADLINK Technology M-322 User manual

Category
Motherboards
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI