HanoverOutdoorFurniture
IMPORTANT
Ifyouhaveanyproblemswiththisproduct(missingordamagedparts,assemblyissues,etc.),
PLEASEDONOTRETURNTOTHERETAILER/STORE
fromwhereyoupurchasedtheproduct.
PleasecallourToll‐FreeCustomerServiceHotlineat:
1‐800‐416‐3511
Between9:00AMand5:00PMEasternTime,MondaythroughFriday
Orvisitourwebsiteat:
www.hanover‐products.com
Toexpediteanyfuturewarrantyclaims,pleaseretaintheInstructionSheet,Warranty
Cardandreceiptforfutureuse.
For additionalon‐linesupportonassembly,troubleshootingandcare&maintenanceofyouroutdoor
furniture,pleasevisitourwebsiteat:www.hanover‐products.com.
6/1/2015(a)
ASSEMBLY INSTRUCTIONS
1
2
.
Place the table rim upside down on a flat, non-abrasive surface. Attach a table leg to the leg connector bracket
by using a 1/4"x15 mm bolt and washer as shown in Guide the bolt through the hole in the table leg, into
the pre-drilled hole in the leg connector bracket. Repeat for the other three legs.
Fig 1.
Hand tighten only.
Attach the table legs to the table top by using the four 1/4"x18 mm bolt and washer as shown in .Fig 2 Hand
tighten only.
.
FOOT CAP
D
F
H
J
C
G
I
J
B
ASSEMBLY INSTRUCTIONS
3
4
After making any necessary adjustments to the alignment of the table, use the hex bolt driver to tighten all bolts.
each bolt must be tightened a few revolutions at a time. In order to apply equal pressure to all bolt joints,
we recommend working in a cross corner (X fashion). Repeat until all bolts are tight. .
Over tightening may strip bolts. Cover all bolts with covers.
Note:
Do not over tighten
At this time, carefully place the fire urn onto the leg connector bracket and through the center hole in table top.
It is recommended that you cover the fire urn when not in use. (For additional information on the use of your fire
urn, please read your attached handbook.)
A
E
*NOTE:PARTSSHOWNONPARTSLISTARENOTTOSCALE
PARTS IDENTIFICATION LIST
1
G0003
TOUCH-UP PAINT
PARTS LIST DESCRIPTION ORDER PART #
BOLT COVER
HEX BOLT DRIVER
1/4" X 15 MM BOLT
Ø6.5 X 1.0 MM
WASHER
1/4" X 18 MM BOLT
TABLE LEG
LEG CONNECTOR
BRACKET
TABLE TOP
QTY
12
1
8
4
8
4
1
1
HW0105
HW0006
HW0004
HW0034
HW0035
FOOT CAP
FACTORY ASSEMBLY
A
B
C
D
E
F
G
H
I
J
K
L
1
ALUMINUM COVER
FIRE URN
1
FC0069
Ø12XØ6.5 X 1.0 MM
WASHER
4
HW0188
FP0853
FP0850
FP0851
FP0852
GFP-084
-
1
-
2
-
3
-
4
Hanover MONCHS3PC-URN Installation guide
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Hanover TRADDN11PCOS4-SW6 Installation guide
-
-
-
-
Hanover TRADDN5PCBN-RED Installation guide
-
-
-
Hanover TRADDN5PCBN-SU-T Installation guide
-
-
Hanover TRADDN5PCSW2BN-RED Installation guide
