MicroNet SP328 / SP328-20 User manual

MicroNet
Brand
MicroNet
Model
SP328 / SP328-20
Category
Network media converters
Type
User manual
User’s Manual
SP362B/SP363B/SP373/SP328 Series
Twist Pair to Fiber Ethernet Media Converter
http://www.micronet.info
Package Content
Thank you for purchasing Micronet Ethernet Media Converter. Before you start
installing the Media Converter, verify the following items in the package
● Media Converter ● User’s Manual
● Power Adapter
Product Overview
The SP362B/SP363B 1000BASE-TX to 1000BASE-SX/LX converter is primarily
designed for larger and higher bandwidth demanding workgroups that require
expansion of the Ethernet network. SP362B/SP363B features a RJ45 jack and
an SC fiber optic connectors, connecting the 1000BASE-TX network to the
1000BASE-SX/LX (fiber optic) network. At full duplex mode, the converter can
extend distances up to 55o meters for Multi-mode fiber and up to 20 kilometers
for Single-mode fiber.
The SP373 Series 10/100BASE-TX to 100BASE-FX converter is primarily
designed for larger and higher bandwidth demanding workgroups that require
expansion of the Ethernet network. SP373 Series Converter features a RJ45 jack
and an ST/SC/MT-RJ/VF-45 fiber optic connectors, connecting the 10/100Mbps
network to the 100BASE-FX (fiber optic) network. At full duplex mode, the
converter can extend distances up to 2 kilometers for Multi-mode fiber and up to
75 kilometers for Single-mode fiber.
To respond to the immediate need in the 10Base Fiber Environment, Micronet
now offers 10/100Base-T/TX to 10Base-FL switching Media Converter Series to
meet such 10Base-FL environment demand.
All of SP362B/SP363B/SP373/SP328 Series converter is wall mountable, and
mountable in SP386 chassis.
Installation
As with any electric device, you should place the equipment where it will not be
subjected to extreme temperatures, humidity, or electromagnetic interference.
Specifically, the site you select should meet the following requirements:
1. The ambient temperature should be between 0 to 40 degrees Celsius.
2. The relative humidity should be less than 90 percent, non condensing.
3. Surrounding electrical devices should not exceed the electromagnetic field
(RFC) standards for IEC 801 3, Level 2 (3V/M) field strength.
2
4. Make sure that the equipment receives adequate ventilation. Do not block
the ventilation holes on each side of the switch or the fan exhaust port on
the side or rear of the equipment.
Follow the steps to install the media converter. This Converter is a plug-and-play
device.
1. Connect the supplied AC to DC power adapter to the receptacle at the back
of the converter.
2. Attach the plug into a standard AC outlet with a voltage range from 100 to
240 VAC.
SP362B/SP363B Gigabit Converter
This converter provides one TX port and one FX port. For the FX port, it provides
options of either multi-mode (SP362B) or single-mode (SP363B) fiber
accommodating SC connector. For the TX port, it uses RJ-45 connector and
supports Auto-Uplink.
Cable Connection of SP362B
Port type Cable Type Max. Length
1000BASE-T Cat. 5, 5E UTP, RJ-45 100 meters
1000BASE-SX Multi-mode Fiber of 850nm (62.5/125µm) 220 meters
1000BASE-SX Multi-mode Fiber of 850nm (50/125µm) 550 meters
Cable Connection of SP363B-10/20
Port type Cable Type Max. Length
1000BASE-T Cat. 5, 5E UTP, RJ-45 100 meters
1000BASE-LX
Single-mode Fiber of 1300nm (9 or
10/125µm)
10 km (SP363B-10)
20 km (SP363B-20)
LED Indication
Please refer to the following table for LED indication of SP362B/SP363B
LED Status Indication
PWR Steady The Power is on
Steady A valid network connection established on TX port LNKC
Off No connection
3
Steady A valid network connection established on Fiber port
LNKF
Off No connection
Steady Connection in full duplex mode
Flashing Collision occurred
FDX/COL
Off Connection in half-duplex mode
Steady Receiving data RX
Off No reception
Steady Transmitting data TX
Off No transmission
DIP Setting of SP362B/SP363B
Port settings are made very simple by means of a DIP (Dual Inline Package)
switch at the front panel of the module. The default setting is auto negotiation as
shown below. If the Pin 1 is on, it means the fiber port will automatically choose
Full Duplex or Half Duplex. User could toggle off Pin 1 to force the fiber port at
Full Duplex. Pin 2 is now reserved for future use.
SP373 Series 10/100TX to 100FX Converter
This converter provides one TX port and one FX port. For the FX port, it provides
options of either multi-mode or single-mode fiber accommodating
ST/SC/MT-RJ/VF-45 connector. For the TX port, it uses RJ-45 connector and
supports auto senses the speed of 10/100Mbps.
Cable Connection of SP373A/B/C/D
Port type Cable Type Max. Length
10/100BASE-T Cat. 3, 4, 5 UTP, RJ-45 100 meters
100BASE-FX
Multi-mode fiber of 62.5/125µm or
50/125µm
2 km
4
Cable Connection of SP373B-15/40/75
Port type Cable Type Max. Length
10/100BASE-T Cat. 3, 4, 5 UTP, RJ-45 100 meters
100BASE-FX
Single-mode Fiber of 1300nm (9 or
10/125µm)
15 km (SP373B-15)
40 km (SP373B-40)
75 km (SP373B-75)
LED Indication
Please refer to the following table for LED indication of SP373 Series
LED Status Indication
Steady The Power is on PWR
Off The Power is off
Steady Connection at speed of 100Mbps 100 (Mbps)
Off Connection at speed of 10Mbps
Steady A valid network connection established LNK/ACT
Flashing Transmitting or receiving data
Steady Connection in full duplex mode
Flashing Collision occurred
FDX/COL
Off Connection in half-duplex mode
DIP Setting of SP373 Series
Port settings are made very simple by means of a DIP (Dual Inline Package)
switch at the rear panel of the module. The default setting is auto negotiation as
shown below. A connected network device might fail to respond to the auto
negotiation mechanism due to various reasons, and therefore, this DIP switch
allows user to manually adjust the TX/RX speed and duplex modes.
There are six pins on the DIP switch for port settings. Refer to the table below for
5
more details.
Pin1 Pin2 Pin3 Pin4 Pin5 Pin6
TX_100
(Mbps)
TX_10
(Mbps)
TX_ Full
duplex
TX_ Half
duplex
Auto
negotiation
disabled
FX_ Full
duplex
First, disconnect the converter from the power. Then toggle Pin 5 of the DIP
switch to the ON position to disable the default setting. Please note that the Pin 5
must be toggled on prior to any port settings manually.
z Toggle on Pin 1 to force the TX port at speed of 100Mbps. Toggle on Pin 2
for 10Mbps speed.
z Toggle on Pin 3 to force the TX port at full duplex mode. Toggle on Pin 4 for
half duplex mode.
z Toggle on Pin 6 to force the FX port at full duplex mode.
Note: If Pin 1 and Pin 2 are toggled on at the same time, the TX port will be set at
10Mbps. If Pin 3 and Pin 4 are toggled on at the same time, the TX port will be set
at half duplex mode.
Connect the converter to the power again. The new setting will come into effect
then. For example: For TX port at 100Mbps, full duplex and FX port at 100Mbps,
full duplex, the DIP switch will be as shown below.
SP328 Series 10/100TX to 10FL Converter
This converter provides one TX port and one FX port. For the FX port, it provides
options of either multi-mode or single-mode fiber accommodating ST connector.
For the TX port, it uses RJ-45 connector and supports auto senses the speed of
10/100Mbps.
P/N: 2300-0161
6
Cable Connection of SP328
Port type Cable Type Max. Length
10BASE-T Cat. 3, 4, 5 UTP, RJ-45 100 meters
100BASE-TX Cat. 5 UTP, RJ-45 100 meters
10BASE-FL Multi-mode fiber of 62.5/125µm 2 km
Cable Connection of SP328-20
Port type Cable Type Max. Length
10BASE-T Cat. 3, 4, 5 UTP, RJ-45 100 meters
100BASE-TX Cat. 5 UTP, RJ-45 100 meters
10BASE-FL Single-mode fiber of 10/125µm 20 km
LED Indication
Please refer to the following table for LED indication of SP373 Series
LEDs Status Indication
Steady Power on
PWR
Off Power off
Steady A valid connection for FX port established
LNK
Off No valid connection for FX port established
Steady
FX port transmitting or receiving data in full duplex
mode
Flashing
FX port transmitting or receiving data in half duplex
mode
ACT/COL
Off FX port neither transmitting nor receiving data
Steady A valid connection for TX port established
Flashing TX port transmitting or receiving data
LNK/ACT
Off No valid connection for FX port established
FDX/COL
Steady TX port connecting in full duplex mode
7
8
Flashing Collision occurred for TX port
Off TX port connecting in half duplex mode
Steady TX port connecting at speed of 100Mbps
100
Off TX port connecting at speed of 10Mbps
SPECIFICATIONS OF SP362B/SP363B
MODEL SP362B
SP363B-XX
STANDARD IEEE802.3ab
1000BASE-T; IEEE802.3z
1000BASE-SX
IEEE802.3ab
1000BASE-T; IEEE802.3z
1000BASE-LX
INTERFACE 1000 Mbps port x 1, RJ-45
1000 Mbps Fiber port x 1, SC connector
TP CONNECTIONS 1000BASE-T: UTP Category 5, 5E ; RJ-45
FIBER CONNECTIONS 1000BASE-SX:
62.5/125µm or 50/125µm
Multi-mode fiber, SC
connector
1000BASE-LX: 9 or
10/125µm Single-mode
fiber, SC connector
LED INDICATIONS Power; TX Link/FX Link; Full Duplex/Collision; TX/RX
MAX. DISTANCE 550m 10km and 20km
FILTERING
/FORWARDING RATE
1000Mbps: 1,488,000pps/1,488,000pps
ENVIRONMENT Operating Temp: 0 ~ 40°C
Storage Temp: -25 ~ 70°C
Humidity: 10 ~ 90% non-condensing
POWER 12V 600mA
NET WEIGHT 150 g
EMISSION FCC Class A, CE
SPECIFICATIONS OF SP373 Series
MODEL SP373A SP373B SP373C SP373D SP373B-XX
STANDARD IEEE802.3 10BASE-T; IEEE802.3u 100BASE-TX/FX
TP PORT 10/100 Mbps port x 1, RJ-45
100BASE-FX
PORT
ST SC MT-RJ VF-45 SC
TP
CONNECTIONS
10BASE-T: UTP Category 3,4,5 ; RJ-45
100BASE-TX : UTP Category 5 ; RJ-45
FIBER
CONNECTIONS
62.5/125µm or 50/125µm multi-mode fiber
9 or 10/
125µm
Single-mode
LED
INDICATIONS
Power; Speed; Link/Activity; Full Duplex/Collision
MAX. DISTANCE
2km
15, 40 and
75km
FILTERING
/FORWARDING
RATE
10Mbps: 14,880pps/14,880pps
100Mbps: 148,800pps/148,800pps
ENVIRONMENT Operating Temp: 0 ~ 40°C
Storage Temp: -25 ~ 70°C
Humidity: 10 ~ 90% non-condensing
POWER 12V 600mA
NET WEIGHT 150 g
EMISSION FCC Class A, CE
9
SPECIFICATIONS OF SP328 Series
MODEL SP328 SP328-20
STANDARD IEEE 802.3 10Base-T/FL, IEEE 802.3u 100Base-TX
TP PORT 10/100 Mbps port x 1, RJ-45
10BASE-FL
PORT
ST
TP
CONNECTIONS
10BASE-T: UTP Category 3,4,5 ; RJ-45
100BASE-TX : UTP Category 5 ; RJ-45
FIBER
CONNECTIONS
62.5/125µm multi-mode
fiber
10/ 125µm Single-mode
LED
INDICATIONS
Power; Speed; Link/Activity; Full Duplex/Collision
MAX. DISTANCE 2km 20km
FILTERING
/FORWARDING
RATE
10Mbps: 14,880pps/14,880pps
100Mbps: 148,800pps/148,800pps
ENVIRONMENT Operating Temp: 0 ~ 40°C
Storage Temp: -25 ~ 70°C
Humidity: 10 ~ 90% non-condensing
POWER 12V 600mA
NET WEIGHT 150 g
EMISSION FCC Class A, CE
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

MicroNet SP328 / SP328-20 User manual

MicroNet
Brand
MicroNet
Model
SP328 / SP328-20
Category
Network media converters
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents