Quick Installation Guide
EtherFast Gigabit Switch
Model No.: SP6105/SP6108
http://www.micronet.info
1
Introduction
Micronet SP6105/SP6108 5/8 ports Gibgabit Switch offers
non-blocking wire-speed Gigabit Ethernet solution for enterprise and
SOHO. It allows you to integrate 10 M, 100M, and 1000M Ethernet
networking devices on your networks easily. Moreover, Micronet
SP6105/SP6108 provides high speed and extra bandwidth to
conquer network bottlenecks and improve speed up the traffic
between your networks.
Key Features
y Complies with IEEE802.3 10Base-T, IEEE802.3u 100Base-TX,
IEEE802.3ab 1000Base-T standards
y Provide 5/8 RJ-45 ports of 10/100/1000Mbps, auto-negotiation
y Support 802.3x flow control for full-duplex mode and
back-pressure flow control for half-duplex mode
y 8K MAC address entries
y Support jumbo frame up to 9.6K bytes
y Support auto uplink, no more cross-over cable
y Forward and filter packets at non-blocking, full wire speed
Package Contents
Please verify the following items are in the package:
y 5/8 Ports Gigabit Switch
y Quick Installation Guide
y Mounting kit
y Power Adapter
2
Tour of the System
Front Panel
SP6105
SP6108
Back Panel
SP6105
SP6108
3
For definitions of LED indicators, please refer to the following table:
LED Status Operation
Steady Green Power is on POWER
Off Power is off
Steady Green
Network connection
established
Blinking Green
Transmitting or receiving
data
LINK/ACT
Off No connection
4
Hardware Installation
Micronet SP6105/SP6108 does not require software configuration.
You can immediately use the Switch simply by attaching the RJ45
Ethernet cables and turning on the power.
The setup of the Switch can be performed using the following steps:
Step1:
•Connect a RJ-45 Ethernet cable from the computer to an
available Ethernet port on SP6105/SP6108.
Step2:
•Connect the AC Power Adaptor to SP6105/SP6108 and then
to a power outlet.
For cable selection, refer to the following table:
Network Speed Cable Type Max. Length
10M Cat. 3,4,5,5e UTP/STP 100 meters
100M Cat. 5,5e UTP/STP 100 meters
1000M Cat. 5e, 6 UTP/STP 100 meters
Note: To prevent costly equipment damage and downtime, please
consider installing a surge suppression device or a UPS
(Un-interrupted Power Supply).
5
Specifications
Module SP6105 SP6108
Standards z IEEE802.3, IEEE802.3u
z IEEE802.3ab
z IEEE802.3x flow control
Interface 5 x RJ-45 ports 8 x RJ-45 ports
Cable Connection z 10BASE-T : Category 3, 4, 5, 5e UTP/STP
z 100BASE-TX : Category 5, 5e UTP/STP
z 1000BASE-TX : Category 5e, 6 UTP/STP
Network Speed z 10/100/1000Mbps
z Half/Full Duplex
z Auto Detection
Uplink Auto uplink (MDI/MDI-X)
Consumption 10 Watts(Max.) 12 Watts(Max.)
Memory 112 Kbytes 144 Kbytes
MAC Address
Table
8K entries
Jumbo Frame 9.6 Kbytes
Filtering/
Forwarding Rate
z 10Mbps: 14,880pps/14,880pps
z 100Mbps: 148,800pps/148,800pps
z 1000Mbps: 1,488,000pps
Emission FCC, CE
Humidity 10 ~ 90% (Non-Condensing)
Temperature 0 ~ 55°C
Dimension (mm) 130 x 77 x 24 (L x W x H) 130 x 97 x 24 (L x W x H)
Power Supply External power adapter
7.5V DC 0.8A
External power adapter
5V DC 2.5A
6
7
FCC Certifications
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and
radiates radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to
correct the interference at own expense. This device complies with
Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including
interference that may cause undesired operation.
CE Mark Warning
This equipment complies with the requirements relating to
electromagnetic compatibility of the essential protection requirement
of Council Directive 89/336/EEC on the approximation of the laws of
the Member States. Company has an on-going policy of upgrading
its products and it may be possible that information in this document
is not up-to-date. Please check with your local distributors for the
latest information. No part of this document can be copied or
reproduced in any form without written consent from the company.
P/N: 2300-0534
/
