Extron One XTP DTP 24 Punch Down Jack User manual

Extron
Brand
Extron
Model
One XTP DTP 24 Punch Down Jack
Type
User manual

This manual is also suitable for

XTP DTP 24 Punch Down Jack • Setup Guide
The following tools are required to terminate the shielded XTP DTP 24 punch down connector:
Follow these instructions to terminate the connector:
1. Slide the rear case of the connector over the
cable. Push the case back at least 3 inches
(76 mm) to make room for the termination of the
cable.
2. Remove about 2 inches (50 mm) of the cable
jacket.
3. Fold down the braid over the cable jacket.
Remove the foil and mylar shielding (if present).
4. Note the color codes and pin numbers on the
sides of the connector. Follow the color code in
the table at right to wire the connector.
5. Untwist the wire pairs and hold the end of the
stripped cable jacket close to the back of the
connector. The length of the exposed wires in the
connector should not exceed 0.6 inch (see image
at right).
ATTENTION: Failure to position the
cable properly may result in crosstalk and
improper termination.
Slide Rear Case
over Cable
1
Strip Jacket 2"
2
Strip Jacket 2"
Fold Braid over Jacket
and Remove Foil
3
4
Color-coded Label
w/ Pin Number
Color Code B
IDC Slots
21 45
A
B
5
6
Distance Between
Cable and Connector
0.6"
IDC
Position
T568B Wiring
IDC Numbers & Color Codes
White/Blue
T568B
Wire Colors
5
4
1
2
3
6
7
8
Blue
White/Orange
Orange
White/Green
Green
White/Brown
Brown
110-Style Punchdown Tool
(Provided)
Wire Cutter RJ-45 Tester
6. Position each wire into its respective IDC slot. Insert
the wires just far enough to hold them in the IDC slots.
7. Use the 110-style punchdown tool to push down
each wire into the IDC slot. Push the punchdown
tool until the wire is rmly secured at the bottom
of the slot.
8. Trim the excess wire ush with the body of the
connector.
9. Tighten the grounding tie around the braid.
10. Remove the excess braid at the grounding tie.
11. Place the plastic cover over the termination wires
for secure connection and added strain relief.
12. Push the rear case forward until it clicks into
position over the terminated connector.
13. Test both ends of the cable for conductivity.
NOTE: If there is a need to re-terminate the
connector, insert a tweeker on the bottom of the
rear case and slide it back to access the wires.
NOTE: The wire retention mechanism in these
connectors is very secure. If a terminated cable
must be separated from its connector, separate
it one wire at a time.
68-2370-50
Rev. C
04 13
Extron USA Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West: +1.714.491.1500 FAX: +1.714.491.1517
Extron USA - East: +1.919.850.1000 FAX: +1.919.850.1001
© 2013 Extron Electronics — All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
7
110 - Style
Punchdown Tool
8
Trim Excess
Wire
9
Grounding
Tie
21 45
A
B
11
10
Plastic
cover
12
Rear Case
  • Page 1 1
  • Page 2 2

Extron One XTP DTP 24 Punch Down Jack User manual

Extron
Brand
Extron
Model
One XTP DTP 24 Punch Down Jack
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents