Siemens SIMATIC ET 200SP HA User manual

Brand: Siemens

Model: SIMATIC ET 200SP HA

Category: Digital & analog I/O modules

Type: User manual

SIMATIC

ET 200SP HA

Digital Input Module DI 8x230VAC

HA (6DL1131-6GF00-0PK0)

Manual

05/2017

A5E39401560-AA

Security information 1

Preface 2

Product overview 3

Wiring 4

Parameters 5

Displays and interrupts 6

Technical specifications 7

Drivers, parameters,

diagnostics messages and

address space A

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will be

used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property

damage.

Qualified Personnel

The product/system described in this documentation may be operated only by personnel qualified for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified

personnel are those who, based on their training and experience, are capable of identifying risks and avoiding

potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended or

approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software described.

Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in

this publication is reviewed regularly and any necessary corrections are included in subsequent editions.

Siemens AG

Division Process Industries and Drives

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E39401560-AA

Ⓟ 05/2017 Subject to change

Table of contents

1 Security information......................................................................................................................................5

2Preface.........................................................................................................................................................7

3Product overview..........................................................................................................................................9

3.1 Properties of the I/O module DI 8x230VAC HA.......................................................................9

4Wiring.........................................................................................................................................................11

4.1 Pin assignment of the I/O module DI 8x230VAC HA.............................................................11

4.2 Schematic circuit diagram......................................................................................................13

5 Parameters.................................................................................................................................................15

5.1 Parameters of the I/O module DI 8x230VAC HA...................................................................15

5.2 Module/channel parameters...................................................................................................15

5.3 Explanation of the module/channel parameters.....................................................................15

6 Displays and interrupts...............................................................................................................................17

6.1 Status and error displays of the I/O module DI 8x230VAC HA..............................................17

6.2 Interrupts................................................................................................................................18

7 Technical specifications..............................................................................................................................21

A Drivers, parameters, diagnostics messages and address space...............................................................25

A.1 Concept of the driver and diagnostics blocks.........................................................................25

A.2 Parameter assignment...........................................................................................................26

A.3 Parameter assignment and structure of the module/channel parameters.............................27

A.4 Diagnostics messages and maintenance events...................................................................30

A.5 Address space.......................................................................................................................31

Index...........................................................................................................................................................33

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

Manual, 05/2017, A5E39401560-AA 3

Table of contents

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

4Manual, 05/2017, A5E39401560-AA

Security information 1

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines, and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens’ products and solutions only form one element of such a concept.

Customer is responsible to prevent unauthorized access to its plants, systems, machines and

networks. Systems, machines and components should only be connected to the enterprise

network or the internet if and to the extent necessary and with appropriate security measures

(e.g. use of firewalls and network segmentation) in place.

Additionally, Siemens’ guidance on appropriate security measures should be taken into

account. For more information about industrial security, please visit:

http://www.siemens.com/industrialsecurity.

Siemens’ products and solutions undergo continuous development to make them more secure.

Siemens strongly recommends to apply product updates as soon as available and to always

use the latest product versions. Use of product versions that are no longer supported, and

failure to apply latest updates may increase customer’s exposure to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under

http://www.siemens.com/industrialsecurity.

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

Manual, 05/2017, A5E39401560-AA 5

Security information

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

6Manual, 05/2017, A5E39401560-AA

Preface 2

Validity of the documentation

This device manual describes the DI 8x230VAC HA I/O module with the article number

6DL1131-6GF00-0PK0.

It complements the system manual of the ET 200SP HA Distributed I/O System.

Functions that generally relate to the system are described in this manual.

The information in this device manual and the system/function manuals enables you to put the

ET 200SP HA into operation.

Appendices

The appendices provide information that is relevant for using the ET 200SP HA outside the

PCS 7 environment.

Conventions

Please also observe notes marked as follows:

Note

A note contains important information on the product described in the documentation, on the

handling of the product and on the section of the documentation to which particular attention

should be paid.

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

Manual, 05/2017, A5E39401560-AA 7

Preface

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

8Manual, 05/2017, A5E39401560-AA

Product overview 3

3.1 Properties of the I/O module DI 8x230VAC HA

View of the module

DIAG MT

























DI HA

8x230VAC

7 8

15 16

910

11 12

13 14

C. 6

A.0

C. 2

A.4

D.7

B.1

D. 3

B. 5

C. 6

A.0

C. 2

A.4

D.7

B.1

D. 3

B. 5

1P1 1P2

2P1 2P 2

MAX. 10 A

.0 .1

.2 . 3

.4 .5

.6 .7

3 4

V 1.0 .0

CC 42

6DL1131-6GF00-0PK0

①Module type and designation ⑦Module type color coding

②LED for diagnostics ⑧Product version

③LED for maintenance ⑨Function status and firmware version

④2D matrix code ⑩Color code for selection of the color-coded labels

⑤Wiring diagram ⑪Serial number

⑥LEDs for channel status ⑫Article number

Figure 3-1 View of DI 8x230VAC HA

Properties

The I/O module has the following technical properties:

● 8 electrically isolated digital inputs in four groups (A to D) each to two channels

● Suitable for connection of switches and 2-wire sensors in accordance with IEC 61131, type

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

Manual, 05/2017, A5E39401560-AA 9

The I/O module supports the following functions:

● Firmware update

● I&M identification data

● Parameter reassignment in RUN

● Value status QI

You can configure the I/O module with HW Config and integrate it into your system.

Accessories

The following accessories must be ordered separately:

● Labeling strips

● Color-coded labels

● Reference identification label

● Shield connector

Product overview

3.1 Properties of the I/O module DI 8x230VAC HA

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

10 Manual, 05/2017, A5E39401560-AA

Wiring 4

4.1 Pin assignment of the I/O module DI 8x230VAC HA

Terminal blocks

You can operate the I/O module with the following terminal blocks:

● 6DL1193-6TP00-0DK0, light

● 6DL1193-6TP00-0BK0, dark

The terminal block is not included in the scope of delivery of the I/O module and must be

ordered separately.

Note

You can find additional information on the configuration in the system manual.

WARNING

Risk of death or serious injury from electric shock!

Prior to working on the system and module, always disconnect them from the power supply.

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

Manual, 05/2017, A5E39401560-AA 11

General pin assignment

Table 4-1 Pin assignment of the DI 8x230VAC HA

Terminal assignment Terminal assignment Explanations

1DI A.0 2DI B.1 DI X.n: Input signal, channel n

N X.n: Neutral conductor, channel n

NC (Not Connected) The terminals are not connected to the DI

8x230VAC HA. However, the potentials of the power bus are on these

terminals.

The letters A to D indicate the assignment of the electrically isolated

channels to one of the 4 groups, which allow for a different difference

in potential.

C.6

A.0

C.2

A.4

1P1

NC NC

1P2

2P1

NC NC

2P2

MA X. 10 A

D.7

B.1

D.3

B.5

C.6

A.0

C.2

A.4

D.7

B.1

D.3

B.5

3DI C.2 4DI D.3

5DI A.4 6DI B.5

7DI C.6 8DI D.7

9N A.0 10 N B.1

11 N C.2 12 N D.3

13 N A.4 14 N B.5

15 N C.6 16 N D.7

1P1 NC 1P2 NC

2P1 NC 2P2 NC

2-conductor

/',;Q

1;Q

Wiring

4.1 Pin assignment of the I/O module DI 8x230VAC HA

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

12 Manual, 05/2017, A5E39401560-AA

4.2 Schematic circuit diagram

The following figure shows the block diagram of the DI 8x230VAC HA.

ET 200SP HA

Backplane bus

interface

Backplane bus

Figure 4-1 Block diagram DI 8x230VAC HA

Wiring

4.2 Schematic circuit diagram

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

Manual, 05/2017, A5E39401560-AA 13

Wiring

4.2 Schematic circuit diagram

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

14 Manual, 05/2017, A5E39401560-AA

Parameters 5

5.1 Parameters of the I/O module DI 8x230VAC HA

Configuring

You configure the I/O module with PCS 7 V9.0 or higher.

Parameters

You define the functioning of the I/O module via parameters.

See also

Parameter assignment (Page 26)

5.2 Module/channel parameters

Parameters of the DI 8x230VAC HA

You have the following setting options:

Table 5-1 Parameters and their default settings

Parameters Value range Default Parameter reassign‐

ment in RUN

Efficiency range

Channel activated ● Enabled

● Disabled

Enabled Yes Channel

Potential group ● Use potential group of the

left module

● Allow new potential group

Use potential

group of the left

module

No Module

5.3 Explanation of the module/channel parameters

Channel activated

Specifies whether a digital input is activated or deactivated.

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

Manual, 05/2017, A5E39401560-AA 15

Potential group

A potential group consists of a group of directly adjacent I/O modules within an ET 200SP

station HA, which are supplied via a common supply voltage.

A potential group begins with a light terminal block, via which the required supply voltage is

fed to all I/O modules of the potential group. The light-colored terminal block interrupts the self-

assembling voltage buses to the left neighbor

All other I/O modules of this potential group are plugged into dark terminal blocks. I/O modules

on dark terminal blocks take the potential of self-assembling voltage rail from the left neighbor.

A potential group ends with the dark terminal block, which follows a light terminal block or a

server module in the station configuration.

You can find additional information on the configuration of the potential group in the system

manual

SIMATIC; Distributed I/O System; ET 200SP HA

Parameters

5.3 Explanation of the module/channel parameters

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

16 Manual, 05/2017, A5E39401560-AA

Displays and interrupts 6

6.1 Status and error displays of the I/O module DI 8x230VAC HA

LED displays

The following figure shows the LED displays (status and fault displays) of the I/O module.







DI HA

8x230VAC

DIAG M T

1DI

C. 6

A.0

C. 2

A.4

D.7

B.1

D. 3

B. 5

C. 6

A.0

C. 2

A.4

D.7

B.1

D. 3

B. 5

1P1

1P2

2P1

2P 2

MA X. 10 A

.0 .1

.2 . 3

.4 . 5

.6 .7

V 1.0 .0

CC 42

6DL1131-6GF00- 0PK0

①DIAG LED (green/red)

②MT LED (yellow)

③Channel status LED (green)

Figure 6-1 LED displays

Meaning of the LED displays

The following tables show the meaning of the status and fault displays. You can find remedies

for diagnostic messages in the section Diagnostics messages and maintenance events

(Page 30)

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

Manual, 05/2017, A5E39401560-AA 17

DIAG LED

Table 6-1 Diagnostics display of the DIAG LED

DIAG LED Meaning

Off

The power supply of the ET 200SP HA is disrupted or switched off.

Flashing

Module is not configured.

Module is configured, a diagnostics message is not pending.

Flashing

Module is configured, at least one diagnostic message is pending.

MT LED

Table 6-2 Maintenance display of the MT LED

MT LED Meaning

Off

No maintenance required.

Maintenance is required, i.e. at least one maintenance event has occurred.

Channel status LED

Table 6-3 Status display of the channel status LED

Channel status

LED

Meaning

Off

Process signal = 0 or channel disabled

Process signal = 1 and channel enabled

6.2 Interrupts

The I/O module supports diagnostic interrupts and maintenance messages.

Diagnostics interrupts

The I/O module generates a diagnostic interrupt for the following events:

● Parameter assignment error

● Channel/component temporarily unavailable

Displays and interrupts

6.2 Interrupts

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

18 Manual, 05/2017, A5E39401560-AA

● Retentive memory in carrier module defective

● Retentive memory in the terminal block defective

Maintenance messages

The I/O module generates a maintenance message for the following events:

● Retentive memory in carrier module defective

● Retentive memory in the terminal block defective

Displays and interrupts

6.2 Interrupts

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

Manual, 05/2017, A5E39401560-AA 19

Displays and interrupts

6.2 Interrupts

Digital Input Module DI 8x230VAC HA (6DL1131-6GF00-0PK0)

20 Manual, 05/2017, A5E39401560-AA

Page is loading ...

Siemens SIMATIC ET 200SP HA User manual

Brand: Siemens

Model: SIMATIC ET 200SP HA

Category: Digital & analog I/O modules

Type: User manual

Download PDF

report

Siemens SIMATIC ET 200SP HA User manual

Siemens SIMATIC ET 200SP HA User manual

Related papers

Other documents