CTH340
OWNER S MANUAL
IMPORTANT
WARRANTY INFORMATION INSIDE. PLEASE READ
COLOUR TELEVISION
TV/AV
ALT.
VOL+
VOL-
CH-
CH+
MENU
0
9
8
7
3
2
1
-/--
MUTE
STANDBY
SYS
P.MODE
PIC.
6
5
4
CALL
WARRANTY REGISTRATION
Please read this warranty card.
Keep your purchase receipt to enable you to proceed quickly in the event of a Warranty Service.
Warranty Terms & Conditions
1. TEAC warrants to the original retail purchaser only, that this product is free from defects in material and
workmanship under normal domestic use and authorises free service during the warranty period at any TEAC
Authorised Centre only. TEAC warranty only applies to products purchased, used and serviced in Australia.
2. Subject to the terms herein, this warranty effectively covers the equipment as specified in the Warranty Periods
Table from the date of purchase.
3. All parts, except the external cabinet, are warranted as specified in Warranty Periods Table, and will be repaired or
replaced at the sole judgement of TEAC.
4. Normal customer maintenance as described in the owner’s manual is not covered by this warranty (such as cleaning
VCR heads etc.)
5. This warranty does not apply to equipment showing abuse, damage or that it may have been tampered with, altered
or repaired outside any TEAC Authorised Service Centre. If so, the warranty will be void.
*Your nearest Authorised TEAC Service Centre is listed in your Owners Manual
6. In the event that this unit or any defective parts must be returned to TEAC Service Centres, a copy of this warranty
certificate and of your purchase receipt must be enclosed to be a valid warranty. Such equipment or parts must be
sent freight prepaid to the nearest authorised TEAC Service Centre. After the repair, the unit will be available for
collection by the owner or it will be returned to the owner. The warranty does not cover freight or insurance. In all
cases of in-transit damages or loss, a claim must be filed against the carrier by the purchaser.
7. No one is authorised to assume any liability on behalf of TEAC or impose any obligation on it, in connection with
the sale of any equipment other than as stated in this warranty and outlined above.
8. In no event will TEAC be responsible or liable for indirect or consequential damages from interrupted operations or
other causes.
9. Warranty is not transferable to any subsequent purchaser if the product is sold during the warranty period,
HISENSE PRODUCT
WARRANTY PERIOD
Televisions / Plasma 106 cm and
above
1 Year
LCD televisions 56cm and above 1 Year
Televisions – 51cm and above 1 Year
Televisions under 51 cm 1 Year
Digital Set Top Boxes 1 Year
VCR 1 Year
DVD 1 Year
Audio Systems 1 Year
WARRANTY PROCEDURES
Please keep this information for your own records.
Please refer to the owner’s manual to ensure that you have followed the correct installation and operating procedures.
1. Read owner’s manual carefully
2. If you require Warranty Service, please contact the TEAC Service Centre
3. Please have your purchase receipt as your proof of purchase and the following details completed for a valid
Warranty.
Owner’s Name
Owner’s Address
Postcode
Model Name/No. Serial No.
Dealer’s Name
Dealer’s Address
Postcode
4. Please ensure that your product is packed appropriately upon return to the service centre.
If you have any other queries regarding service or warranty please contact the TEAC Service below:
www.teac.com.au
CONTENTS
WELCOME TO THE BRIGHT, VIVID AND JOYFUL COLOR WORLD
Dear customer,
Thank you for your purchasing this color TV and we wish you many years of viewing pleasure with your new TV.Before
operating the set, please read this manual carefully and keep it handy for future reference.
High voltage inside.
To prevent the risk of electric shock ,do not remove the cover.
No user -serviceable parts inside.
Refer servicing to qualified service personnel .
Do not obstruct ventilation slots in back or base of receiver.
Don't expose the unit in rain or moisture.
Don't
put
water
(or
any
other
kind
of
liquid)-containing
vessel
on
the
set
to
avoid
causing fire.
Before storming, please unplug the antenna and the power supply from their sockets.
This is an IEC safety class II (reinforced insulation) product and does not need grounding for safety.
SAFETY CLASS
NOTICE
Knowin g Your Television Set...........................................3
....................................................5
..............................................................8
...................................
.............................8
Troubleshooting.................................................................1
Installation......................................................................2
........................................ ...4
.......................................6
.............
.......
...................................7
.....................................
..................
....7
Maintenance And Safety Information.............................1
To connect with terrestrial signal source................2
To prepare remote control ......................................2
Front controls...........................................................3
.....................................................
3
...............................
..............................
....7
Basic operation
...... ..............................5
Power/Standby on/off
..... ................................5
Selecting the program
...... . ..............................5
Adjusting the volume
...... . ......................6
Selecting the signal source
...... .....................................
6
Alternating
.......................
6
Calling up on screen display
...... ..............................
6
Muting the sound
Selecting the picture mode
Option1 menu
Clock menu
Picture menu
Option2 menu
Preset menu
...... ..........
....
............
10
Specifications
..
.
..
............
..............
9
Connecting with the audiovisual equipments
...... ......
....
...........
Rear view
Remote control handset
Please read these instructions carefully and do accordingly.
TV set requires adequate ventilation. If you place the set near walls, leave sufficient space (15cm) on all sides so that
the air can circulate freely. The ventilation slots at the rear of the set can not be covered by curtains, newspapers or any
other similar objects.
Do not expose the TV set to direct sunlight or place it near radiator and other similar sources of heat.
TV sets are intended for use in dry rooms. If you wish to use it occasionally outdoors, be sure to protect it against any
kind of moisture (rain,splashes, dew and etc.).
Do not put metal and combustibles into the TV through the rear slots to avoid possible fire or shock hazard.
Do not place water(or any other kind of liquid)-containing vessel on the set.
Do not step on or twist the power cord. A damaged cord may cause fire or shock hazard.
Keep any magnetic object away from the TV as far as possible.
If there is a lightning storm coming, unplug the TV set and the outdoor antenna.
If any abnormal phenomenon
(smoke,
unusual
sound,
or
strange
smell),
stop
using
the
TV
at
once.
Power
it
off and unplug it.
Maintenance And Safety Information
1
occurs
Troubleshooti ng
Before calling the service personnel, please check the list below to fix some simple problems not caused by the unit itself.
Check these things
Be sure the power cord is plugged in.
The sound volume is adjusted to the minimal or in mute position.
May be pulse interference from nearby cars, motorcycles, electric trains, high
tension lines, neon signs, hair dryers, etc.
May be radio interference f
or
m nearby TV receivers, personal computers,
and TV games, or radio station.
May be due to broadcast waves reflected from nearby mounts and high buildings.
Check if the direction of aerial has been deflected because of strong wind, etc.
The aerial lead-in may be broken or disconnected.
Check if the direction of aerial has been deflected because of strong wind, etc.
Clean indicator window.
The batteries maybe have worn out.
The batteries may be improperly installed.
Symptom
No picture. No sound.
Normal picture. No sound.
Poor color, contrast, tint
Spots on screen
Lines on screen
Double/triple image
Snowy picture
Reduction in operating distance
Remote control does not work
May need to adjust contrast, color and tint. Also try fine tuning the stations.
(Ref to page 7)
Try re-tuning in stations.
Can be caused by magnetic interference. Ensure to unplug the TV Set
from the power point for approximately 8-10 hours.
Green/Purple spots
To Connect With Terrestrial Signal Source
To enjoy the terrestrial signal transmitted by your local TV station, you need an indoor or outdoor aerial (not supplied). Perfect
picture quality requires a good signal and generally means that an outdoor aerial must be implemented. The exact type and
location of the aerial will depend on your particular area. Consult your local dealer or service personnel for best advice.
If you are a subscriber of your local CATV net, the outdoor or indoor aerial is not needed.
Connect the equipments as in the following figure.
To Prepare Remote Control
Battery
installation
1.Slide or lift the battery cover from back of remote control.
2.Insert two batteries (1.5V) matching the +/- polarity of the
battery to the +/- marks inside the battery compartment.
3.Close the battery cover by doing reversely to step 1.
Install the unit where sunlight will not fall upon the screen directly.
Total dark environment or a reflection on the picture screen may cause eyestrain. Soft indirect lighting is recommended
for comfortable viewing.
Allow enough space between the unit and the wall for proper ventilation.
Avoid excessively warm locations to prevent possible damage to the cabinet or components.
AERIAL SOCKET
REAR VIEW
The above figures are for reference only, and please refer to the actual units to determine their appearance.
COAXIAL CABLE(75ohm)
TWIN-LEAD FEEDER(300ohm)
Insert the feeder in
Tighten the screw
Plug(not supplied)
Adaptor (not supplied)
The signal comes from:
An outdoor aerial
An indoor aerial
CATV net
Loosen the screw
ANT
75
Notes about using remote control:
1.The
batteries
have
a
typical
operating
time
of
one
yea
r
2.When the remote control will not be used for a long period of
Time or when the batteries are worn out, remove the batteries
to prevent leakage.
3.Do not drop, dampen or disassemble the remote control.
4.The effective range of remote control is suggested in the left
figure.
face to infrared sensor
Installation
2
depending on battery brand and use.
6m
Knowing your television set
3
AC cord and plug
INPUT
Rear view
Front controls
S-VIDEO
VIDEO
L
R
Y
Cb
Cr
ANTENNA
(75 )
VIDEO
L
R
AV2(VI DEO2)
AV1(VI DEO1)
SIDE AV
MENU
POWER SWITCH
VOLUME UP
POWER INDICATOR
VOLUME DOWN
TV/AV
INFRARED SENSOR
PROGRAM UP
PROGRAM DOWN
MENU
TV/AV
+
-
CH
VOL
+
-
Infrared LED
TV/AV
To select signal source
STANDBY
To switch the TV off to standby
mode or on to last viewed position
MENU
To call up the main menu
To call up information display
CALL(DISPLAY)
MUTE
To mute the sound or cancel it
P.MODE
To select the picture modes
PROGRAM UP(CH+)
To select next higher position
VOLUME UP(V+)
PROGRAM DOWN(CH-)
To select next lower position
ALT.(RECALL)
To return to the last viewed position
DIGIT
To select between one(-), two(- -),
or (- - -) three digits program numbers
NUMERIC KEYS
To directly select the program
VOLUME DOWN(V-)
Remote control handset
4
TV/AV
ALT.
VOL+
VOL-
CH-
CH+
MENU
0
9
8
7
3
2
1
-/--
MUTE
STANDBY
SYS
P.MODE
PIC
6
5
4
CALL
PICTURE
To call up the picture menu
SYS
To call up the option2 menu or change
the color system(in video, s-video, YCBCR mode)
MENU
TV/AV
+
-
CH
VOL
+
-
MENU
TV/AV
+
-
CH
VOL
+
-
STANDBY
Basic operation
Power/Standby on/off
To power up the TV, press the power switch located on the bottom-right of the cabinet. The power indicator
lights red and the last viewed program appears. If the power indicator lights up but no picture appears, the
TV may be in standby mode.
To turn the TV on, you can do the following:
1.Press the standby key on handset to get into the last viewed program.
2.Press one of Numerical keys on handset to get into the selected program.
3.Press the CH+/CH- keys on front panel of TV.
When the TV is on, press the standby key to swap the TV to standby mode or press power switch to power
it off completely.
Note:
1. If a power failure occurs when the TV is on, press the power switch to cut off from the power supply to
avoid possible hazard to the TV which may be caused by a high voltage pulse when the power supply restores.
2.The TV set has AUTO SWITCH OFF function, which cause the TV to standby mode after about 15 minutes
of no incoming signal and no operation.
3.Standby mode: Use to turn off TV for a short period of time. If you do not intend to use the TV for a long
period of time it is best to turn it off from the power switch on the television set.
Selecting the program
Directly selecting
To select a one-digit number program, press the digit key to display"-" and then input the number directly with
one of the numeric keys(0-9).
When the number is between 10 and 99, press the digit key to display "--" and then input two numbers with the
numeric keys.
When the number is between 100 and 199, press the digit key to display "---" and then input two numbers with
the numeric keys.
Note:
When you are in multi-digit mode(the display is "--")and the digits are not fulfilled(for example, "2_","12_" ),
the channel will not be changed.
Sequentially selecting
Press the CH+/CH- keys to select the next higher/lower program.
Adjusting the volume
Press the VOL+/VOL- key to adjust the volume.
5
0
9
8
7
3
2
1
-/--
6
5
4
VOL+
VOL-
CH-
CH+
VOL+
VOL-
CH-
CH+
Muting the sound
MUTE
The muting function is useful and convenient when you need to pay attention to surrounding sounds,
answer a phone call, receive a visitor, etc.
Press the mute key to mute the sound and cancel the mute by pressing it again.
Note: (when in muting)
1.Press the V+ key also can cancel the mute.
2.Press the V- key volume will be turn down in muting.
Alternating
ALT.
Press the ALT. key to go back to the program that you've just been watching before the current one.
By pressing it repeatedly, you can alternate between your two favorite programs.
Calling up on screen display
CALL
Press the CALL key to show the current program number on the top-right of the screen.
Press the CALL key again to clear it .
Whenever you want to clear the undesired OSD, press the CALL key.
Selecting the picture mode
P.MODE
The TV set provides four modes for instant selection by touching P.MODE key.
STANDARD
PERSONAL
DYNAMIC
MILD
The STANDARD MILD and DYNAMIC settings can't be adjusted by the user. The PERSONAL setting can be
customized by selecting your personal preference in the Brightness, Color and contrast.
Each time the P.MODE key is pressed, the picture is displayed in one of the above four modes sequentially.
Basic operation
6
Press the TV/AV key to select the video source.
The program you enjoy can come from terrestrial signal(via aerial input socket)
or audio/video signal(via AV input terminals.)
Selecting the signal source
TV/AV
1
VIDEO1
VIDEO2
S-VIDEO
YCBCR
ALT.
MUTE
CALL
TV/AV
P.MODE
Basic operation
7
Picture menu
MENU
Press MENU key to call up Picture menu as shown right:
Press CH+/CH- keys to select the desired item and press V+/V- keys to adjust it with
the keys to customize the picture to your preference.
MENU
80
CONT. 60
COLOR 60
SHARP 60
C.TEMP. 00
BRIGHT
PICTURE
SELECT ADJUST
SLEEP ___
TIME __:__
ON-TIME __:__
OFF-TIME __:__
ATTENTION __:__
PROG. TIMER __:__
POSITION 1
CLOCK
SELECT ADJUST
Press the CH+/CH- keys to select the desired item and activate it with the V+/V- keys.
The items in this Time menu are explained in detail as follows.
'SLEEP', you can set the SLEEP timer to turn off the TV set automatically. The time
period can be adjusted from 0 up to 120 minutes in 15 minutes steps.
'TIME', please set TIME to the current time. This will be used as a reference for all timing functions.
'ON TIME', set ON TIME if you want to turn on automatically the TV at a specific time.
'OFF TIME', set OFF TIME to turn off the unit automatically.
'ATTENTION', the ATTENTION function displays a reminder. The message "ATTENTION" will display at the set time.
'PROG. TIMER ', it allows to change automatically to a different channel at a convenient time, for example when a
program of interest is about to start in another channel.
'POSITION', set POSITION to indicate the desired program number for the PROGRAM TIMER.
Note:
press VOL- key to change the hour, press VOL+ key to change the minutes.
Press MENU key to call up clock menu as shown right:
Clock menu
MENU
MENU
CORING ON
CALENDAR
GAME1
GAME2
LIMIT SET
OPTION1
SELECT ADJUST
Press MENU key to call up option1 menu as shown below:
MENU
MENU
Press the CH+/CH- keys to select the desired item and activate it with the V+/V- keys.
The items in this option1menu are explained in detail as follows.
'CORING', CORING is used to reduce picture noise when set on.
'CALENDAR', allows access to a permanent calendar. You can use CH+/CH- keys to
select the ' 'year' ', ' 'month' ' and' 'day' '. Press VOL-/VOL+ keys to change.
'GAME1', single out ' 'money' ' from six things. Press CALL key to exit game and press ALT. key to restart game.
'GAME2', guess 888. Press CALL key to exit game and press ALT. key to restart game.
''
'' ''
''''
After entering the game, please use V+/V- keys to move the man horizontally; the ALT. key can be used as the pause
key before the game is over, after the game is over, this key becomes the restart key. When it's paused, press the ALT.
Key to restart; press CALL key to exit. All other keys do not work in the state of game except POWER SWITCH. There
are six objects falling down: money bags, coins, snow flakes, crosses, hearts, and bombs. You get 10 credits by
receiving one money bag and 5 credits for one coin. Credits will be added up automatically when it's over. At the start,
the man is green, it becomes white, while receiving snow flake(being frozen) and the moving speed ( left and right)
slows down. This state will be cleared up if a cross is received. It is over if the bomb is received and the figure becomes
red. Receiving Heart, the figure gets purple which lasts 5 seconds during which the game is not over even with receiving
a bomb.
After entering the game, Press ALT. key to start and CALL key to exit.
All other keys do not work in the state of Game except POWER SWITCH.
You get one gold coin by getting one 8 out of 3 numbers, two gold coins by
getting identical numbers which are not 8 , three gold coins by getting two 8 s,
four gold coins by getting three sequential numbers(e.g. 123 , 321 ), and five
gold coins if the numbers are all the same.
DATE:2005 -6- 20
SU MO TU WE TH FR SA
1 2 3 4
5 6 7 8 9 10 11
12 13 14 15 16 17 18
19 20 21 22 23 24 25
26 27 28 29 30
Option1 menu
Preset menu
Press MENU key to call up Preset menu as shown right:
The items in this Preset menu are explained in detail as follows.
'POSITION', presents the number of the current program.
'REMEMBER', is used to disable the current program, if unwanted, when changing channels with CH+/CH- keys .
'BAND', use BAND to select frequency band location of a channel for SEMI-SEARCH tuning.
'FINE TUNING', use FINE TUNING to improve image and sound quality under poor reception conditions.
'SEMI-SEARCH', SEMI-SEARCH can be used to manually tune in individual channels to a specific program number.
This function can also be used if tuning in a VCR.
'AUTO-SEARCH', the AUTO-SEARCH function will tune in automatically all channels available in your area.
Press V+ to start this process.
Note:
Please set COLOUR to AUTO and SOUND to 5.5M before starting AUTO-SEARCH.
Press the CH+/CH- keys to select the desired item and activate it with the V+/V- keys.
Basic operation
8
MENU
MENU
POSITION 1
REMEMBER ON
BAND V-L
FINE
SEMI-SEARCH
AUTO-SEARCH
PRESET
SELECT ADJUST
COLOR-SYS AUTO
SOUND-SYS 5.5M
SHIFT MODE ON
EXCHANGE 001 - - -
COPY 001 - - -
CLEAR ALL
OPTION2
SELECT ADJUST
Press MENU key to call up option2 menu as shown right:
MENU
MENU
Press the CH+/CH- keys to select the desired item and activate it with the
VOL+/VOL- keys.
The items in this option2 menu are explained in detail as follows.
'COLOR-SYS', COLOR-SYS allows the selection of different color systems. Please set to either AUTO or PAL positions.
set it ON to display a black screen during the transition between programs when changing channels.
'SOUND-SYS', SOUND-SYS is for the selection of different sound systems. Please set to 5.5M.
'EXCHANGE', is used to exchange two position's contents.
'COPY', is used to copy previous position's contents.
'CLEAR ALL', is used to clear the programs having been stored.
Please press the V+ key for about three seconds.
'SHIFT MODE', ''
Option2 menu
LIMIT SET
PLEASE INPUT
PASSWORD:
_ _ _ _
LIMIT SET
LIMIT TIME OFF
CHANGE PASSWORD
PLEASE INPUT
NEW PASSWORD
_ _ _ _
INPUT NEW
PASSWORD AGAIN
_ _ _ _
PASSWORD CHANGED
PLEASE REMEMBER
LIMIT SET
LIMIT TIME 00:10
CHANGE PASSWORD
The primary password
is '0000'.
press VOL- key to change the hour,
press VOL+ key to change the minutes.
(for example 10 minutes.)
PLEASE INPUT
PASSWORD:
_ _ _ _
LOCKED
LIMIT SET
LIMIT TIME 00:00
CHANGE PASSWORD
LOCKED
press VOL- key to turn off.
10 minutes later,
the screen will display 'LOCKED'
and the TV program will disappear.
Input your new password
or primary password
The time LIMIT SET function allows you
to restrict the use of the television, for
example to avoid excessive number of
watching hours by children.
This function is password protected.
The initial password is '0000' and it can be
changed following the procedure described
in the diagram. Please keep the new password
in a safe place, as you will need it in the future.
9
Connecting with the audiovisual equipments
To enjoy the programs coming from your audiovisual equipments such as VCR, DVD etc, the signal must be received by the set
via the AV input terminals at rear or side.
Note:
The following figures are only for reference, please refer to the instruction included with your DVD or VCR for direction on how
to connect these to your TV.
RF ou tput
R
AUDIO
L
Audio Input
DVD/LD with YCbCr output
Y
Cb
Cr
R
AUDIO
L
VCR
OUTPUT
AUDIO
VIDEO
AUDIO
INPUT
S-VIDEO
VIDEO
L
R
Y
Cb
Cr
VIDEO
L
R
AV2
AV2
L
R
10
SPECIFICATIONS
MAIN UNIT
TV Receiving System---------------------------PAL,BG
AV Color System---------------------------------PAL,NTSC 3.58 & 4.43
Tuner-----------------------------------------------FS TUNER
Number of Preset Program---------------------200(0-199)
Channel Indicator--------------------------------On screen display
Function Adjust Indicator-----------------------MENU display
Language of OSD--------------------------------English
RF Aerial input------------------------------------75-ohm unbalanced
Video Input----------------------------------------75-ohm 1.0Vp-p, RCA
Audio Input----------------------------------------10k ohm 0.5 Vrms, high impedance
Audio Output Power----------------------------- 2W
Operating Voltage-------------------------------220V-240V , 50Hz
Power Consumption-----------------------------60W
Power Consumption-----------------------------10W(in standby mode)
Picture Tube--------------------------------------14"(34 cm)
Dimensions---------------------------------------390 X 393 X 368 (W X D X H)
Net Weight----------------------------------------10Kg
INFRARED REMOTE CONTROL
Features------------------------------------------Full Function Remote Control
Effective Distance Power----------------------6 meters
Power Supply------------------------------------DC 3V(two batteries, size AAA)
PACKING LIST
1.TV set-------------------one set
2.Remote-----------------one set
3.Operation Manual ----one p c s
Product improvements may result in changes to features and specifications without prior notice.
*
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
