Poly 1354-68669-001 is a Dual 65 inch Center Top Display Rail, a component of the Polycom RealPresence Group Series Media Center. It allows for the attachment of two 65-inch displays to the media center, creating a dual-display setup for video conferencing and content sharing. This configuration is ideal for large meeting rooms and auditoriums, where multiple participants need to view presentations or collaborate on visual content simultaneously.
Poly 1354-68669-001 is a Dual 65 inch Center Top Display Rail, a component of the Polycom RealPresence Group Series Media Center. It allows for the attachment of two 65-inch displays to the media center, creating a dual-display setup for video conferencing and content sharing. This configuration is ideal for large meeting rooms and auditoriums, where multiple participants need to view presentations or collaborate on visual content simultaneously.
Polycom RealPresence Group Series Media Center
with 65 Inch Dual Displays
SETUP SHEET
This supplement describes how to attach 65 inch dual displays on the Polycom RealPresence Group Series
Media Center. Follow the instructions in Setting Up the Polycom RealPresence Group Series Media Center,
1725-08510-00X, and use this supplement to replace the steps to install the displays.
Single 55/65 inch Lower Display Rail, 1354-67626-002
(2) Dual 65 inch Lower Display Rail Extension, 1354-68667-002
Dual 65 inch Center Top Display Rail, 1354-68669-001
(2) Dual 65 inch Upper Display Rail Extension, 1354-68671-001
(4) Display Mounting Bracket
Assembly
2342-67629-001
(4) M8 x 20 Button Head Cap Screw
1601-52713-001
(4) M8 Hex Flange Nut
1600-52845-001
(4) M10 x 25 Flanged Socket Head
Cap Screw
1601-67617-002
M8 Wrench
1102-68064-001
For more information about the components of the RealPresence Group Series Media Center,
refer to the documentation at
http://support.polycom.com/PolycomService/support/us/support/video/group_series/group_packaged_solutions.html.
The Media Center components are heavy. Polycom recommends that two people perform the installation.
© 2021 Plantronics, Inc. All rights reserved. Poly, the propeller design, and the Poly logo are trademarks of Plantronics, Inc. The Bluetooth trademark
is owned by Bluetooth SIG, Inc. and any use of the mark by Plantronics, Inc. is under license. All other trademarks are the property of their respective owners.
1725-68117-003A
Install the lower display rail by aligning the holes in
the display rail with the holes in the vertical
supports. Attach with four M10 x 25 flanged socket
head cap screws. Do not fully tighten.
Install a lower display rail extension to each side of
the lower display rail using two M8 x 20 button
head cap screws and two M8 hex nuts per side.
Ensure the edge of the rail extension is 3.97 inches
from the inner cut edge of the bottom display rail.
Tighten using the supplied M8 wrench.
Attach an upper display rail extension to each end of the center top display rail using two M10 x 25 flanged
socket head cap screws per extension.
Install the upper display rail assembly by aligning the holes in the display rail with the holes in the vertical
supports. Attach with two M10 x 25 flanged socket head cap screws per vertical support. Do not fully tighten.
Attach the rear panel by inserting the two tabs at the
bottom of the door into the slots in the base. This
serves as an alignment tool to ensure the frame is
properly aligned before tightening all bolts. Using
the L-key, tighten the socket head cap screws at
the bottom of the base, the lower display rail, and
the upper display rail. Remove the rear panel.
On the back side, install a handle on both ends
of the bottom display rail.
Install the display mount brackets on the display. For the LG and Sampo 65 inch (PMQ65ML) display, position
the display mounting bracket using the sixth hole from the top with the top mounting hole on the display. The
bottom hole on the display is the seventh hole up from the bottom of the bracket.
For the Sampo 55 inch and 65 inch (PME65MA) display, position the third hole down from the top of the
display bracket with the third hole down from the top of the display. The bottom hole on the display lines up
with the fifth hole up from the bottom of the display bracket.
Install the supplied 1/4-20 x 3.5 inch socket head cap screws at the top of each display bracket. Leave the
screws adjusted up before mounting the display to the top rail.
Repeat with the second display.
With the assistance of another person, lift the display and position the display bracket hooks above the edge
of the upper horizontal display rail on the Media Center. Carefully lower the display onto the rail, ensuring the
hooks are fully engaged with the rail and that the outer most bracket is positioned within the safety tab on the
outer rail end (1). Repeat with the second display.
Adjust the leveler screws as needed to help eliminate any gap between the two displays when they are tightly
abutted (2).
Center the displays on the Media Center. Insert one M6 x 16 flanged button head screw into each outer
display bracket to lock the displays.
Power Rating:
Voltage rating: 100-240 VAC, 50/60Hz
Maximum power consumption (configured with Group
Series 500 codec and EagleEye IV camera under full
load operating conditions):
651.4W with Sampo (PME65MA) display
591.4W with Sampo (PMQ65ML) display
651.4W with LG display
Approximate system weight (including displays,
codec, camera, and sound system):
715 lbs. with Sampo (PME65MA) display
613 lbs. with Sampo (PMQ65ML) display
555 lbs. with LG display
Regulatory Notices:
This equipment is intended for indoor use only.
Only use this equipment with the displays supplied by
Polycom.
Do not use a power cord that is damaged. This could cause
fire or electric shock. Contact the manufacturer for a
replacement cord, if necessary.
Only use a power cord which is appropriately rated and
approved relevant to the country of use.
This equipment should be used only on even surfaces.
When moving or positioning the system, only use the
handles located at the bottom of the display rail at the rear
of the unit.
This equipment has lockable wheels which should be
applied while the cart is stationary.
When connecting to the mains supply, connect only to an
earthed supply outlet which is installed near the equipment
and is easily accessible.
Keep ventilation openings free from any obstructions.
The ambient operating temperature rating of this equipment
is 0 - 40ºC and should not be exceeded.
Do not immerse the system in any liquid or place any liquids
on it.
Do not spray liquids directly onto the system when cleaning.
Always apply the liquid first to a static-free cloth.
For further information concerning the individual components
of this equipment, please refer to the respective product
literature.
For support or service, please contact your Poly
distributor or go to the Poly Online Support Center at
support.polycom.com/content/support.html.
-
1
-
2
-
3
-
4
-
5
Poly 1354-68669-001 is a Dual 65 inch Center Top Display Rail, a component of the Polycom RealPresence Group Series Media Center. It allows for the attachment of two 65-inch displays to the media center, creating a dual-display setup for video conferencing and content sharing. This configuration is ideal for large meeting rooms and auditoriums, where multiple participants need to view presentations or collaborate on visual content simultaneously.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Poly Medialign Installation guide
-
-
Poly RealPresence Desktop Quick start guide
-
Poly RealPresence Desktop Quick start guide
-
-
-
Poly G7500 User guide
-
Polycom RMX 1500 User guide
-
Poly RMX 2000 User guide
-
Other documents
-
Polycom RealPresence Group Series Setting Up
-
-
-
Polycom RealPresence RMX 1800 Getting Started Manual
-
-
-
-
-
-