V-ZUG 283 Installation guide

Page is loading ...

Installation instructions

Convenient storage drawer

for tumble driers

J283.050-3

13.8.09 ITH

7

These installation instructions apply to the models: 283–286, 296, 954–959

* Material is not required with the tumble drier.

Plinth W5.2014 (for visual adaptation).

Preparation

1. Unplug the mains connection plug or switch off at the wall switch.

Installation

2. Pull the appliance out of the niche and remove the

installation plate from the floor; this is no longer required.

3. Place the convenient storage drawer 1 on the same spot

and remove the drawer 2 by lifting the black rail springs 4

at the side.

4. Stick the installation template 3 to the floor centrally

between the adjustable feet.

The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order

specified.

Validity

General notes

A full repair can only be guaranteed providing the non-destructive deinstallation of the complete appliance is possible at any

time.

Installation accessories included

Designation Number of items Designation Number of items

Floor mounting plate incl. double sided adhesive discs 2 U-washers St EZN * 4

Nylon plug Delta size 6 2 Combi spanner 19 mm 1

Countersunk head wood screws 5 × 30 2 Combi spanner 27 mm * 1

Installation template for floor mounting plate 1 Hexagon box spanner * 1

Hexagon nuts 0.8D St EZN * 4 Allen key * 1

Options

Dimensions

Installation

Lifting and positioning of the tumble drier must be carried out by 2 persons. During installation the tumble drier must not be

tilted from the vertical by more than 45°, otherwise the appliance will have to be left standing in its normal operating position

for about 2 hours prior to startup.

43021

~340

550

595

Top view

4

2

1

3

Installation instructions

Convenient storage drawer

for tumble driers

J283.050-3

13.8.09 ITH

8

5. Affixing the floor mounting plates

A Remove the protective film from the mounting plates.

A Lift up the convenient storage drawer and the appliance at the front and move it aside in order to

stick the mounting plates in position.

A Clean the adhesive zone with pure benzine or acetone.

A Taking the fixing position from the installation template 3, stick the mounting plates to the floor.

Screwing the floor mounting plates

A Move the convenient storage drawer aside to drill the mounting plates.

A Mark the centre of the holes, using the installation template 3.

A Drill ø 6 mm holes and insert plugs. Screw the mounting plate in place. Drilling inaccuracies can

be compensated by means of the eccentric hole in the mounting plate.

6. Pull the convenient storage drawer out of the niche and remove the installation template.

7. Unscrew the adjuster feet by hand until the folded installation

template 3 fits under the appliance 5 at all 4 corners (see

detail X).

8. Lift the appliance and push the front adjuster feet from above

into the finished profile 6 of the convenient storage drawer.

9. Place the rear adjuster feet in the positioning plate 7. Where

necessary, level the appliance to obtain a uniform gap of 2 mm

between the appliance and the convenient storage drawer.

10. Place appliance and convenient storage drawer in position.

11. Insert the drawer and slide in until the rail springs re-engage.

12. Mount plinth W5.2014 where applicable.

Tools: Combi spanner 19 mm 8 (supplied) and spirit level 9

Rear adjuster feet

A Loosen lock nuts 10.

A Align convenient storage drawer vertically by turning the foot by hand.

A Tighten the lock nuts firmly.

Front adjuster feet

A Place the appliance in the floor mounting plate.

A Loosen lock nuts 10.

A Align convenient storage drawer vertically by turning the foot by hand.

– Convenient storage drawer and appliance must be absolutely stable.

A Tighten the lock nuts.

To avoid damaging the convenient storage drawer, set the adjuster feet to the correct height of 22 mm, using the installation

template 3, before placing the appliance in position.

Levelling

For fault-free operation the convenient storage drawer must stand perpendicular to the appliance with all feet firmly on the

ground and the lock nuts 10 must be firmly tightened.

3

==

5

7

3

22

2

6

Detail X

8

9

10

V-ZUG 283 Installation guide

V-ZUG 283 Installation guide

in other languages

Related papers

Other documents