Home Styles 5100-0063-62 Assembly Instructions

Type
Assembly Instructions

This manual is also suitable for

88 5100 306
Hutch
Home Styles Consumer Assistance : www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
Part List
IMPORTANT NOTE
.
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit
Cam Lock
18 Pcs. (+2 extra)
Adjustable Pin
12 Pcs. (+1 extra)
M4x25
Machine Screw
2 Pcs.
Knob
2 Pcs.
Steel Plate Connector
2 Pcs.
M3.5x16
Wood Screw
for Back Panel
12 Pcs. (+1 extra)
M4x13
Wood Screw
for Steel Plate Connector
8 Pcs. (+1 extra)
Cam Lock Screw
18 Pcs. (+1 extra)
A.
To p
1 Pc.
F.
Back Stretcher
1 Pc.
G.
Back Stretcher
1 Pc.
H.
Front Stretcher
1 Pc.
I.
Fixed Shelf
1 Pc.
J.
Shelf
1 Pc.
K.
Shelf
2 Pcs.
L.
Middle Panel
1 Pc.
M.
Middle Panel
1 Pc.
N.
Door
1 Pc.
O.
Door
1 Pc.
B.
Side Panel
1 Pc.
C.
Side Panel
1 Pc.
D.
Back Panel
3 Pcs.
E.
Back Upright
2 Pcs.
Hutch Unit
Assembly Instructions 2/5
IMPORTANT
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
STEP 1
Insert Cam Lock Screws into pre-drilled holes of
Top (A), Side Panels (B), (C) and Fixed Shelf (I).
(See Figure 1)
Attach Back Uprights (E) to Back Stretcher (G).
STEP 2
Slide Back Panels (D) into place.
Attach Back Stretcher (F) to Back Uprights (E).
Attach Middle Panels (L) and (M) to
STEP 3
Fixed Shelf (I) with Cam Locks.
(See Figure 2)
B
I
D
D
D
E
F
G
I
L
M
E
A
C
Figure 1
Cam Lock Screw
Cam Lock
Figure 2
Assembly Instructions 3/5
STEP 4
Attach unit from Step 2,
Front Stretcher (H) and Side Panel (B)
to the unit from Step 3 with Cam Locks.
Attach Side Panel (C) to the unit
with Cam Locks.
Turn the unit to its’ upright position.
STEP 5
Attach Top (A) to unit with
Cam Locks.
Insert Adjustable Pins into
side panels and middle panels
at the desired level.
Place Shelf (J) and Shelves (K)
into position.
Attach Knobs to Door (N) and (O) with
Machine Screws.
(See Figure 3)
Attach Door (N) and (O) to side panels by sliding the door lift hinges into side panel lift hinges.
(See Figure 4)
H
B
A
N
J
K
K
O
C
Cam Lock
Cam Lock
Adjustable Pin
Figure 3
Figure 4
Assembly Instructions 4/5
STEP 9
Insert 12X Wood Screws for Back Panel
into pre-drilled holes of Back Panel.
Place Hutch onto Buffet.
Attach Steel Plate Connectors using
STEP 7
STEP 8
Wood Screws for Steel Plate Connector.
(See Figure 5)
Wood Screw
Figure 5
Wood Screw
for Steel Plate
Connector
Steel Plate
Connector
for Back Panel
M3.5x13
Wood Screw
1 pc.(+1 extra)
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
M3.5x40
Wall Screw
1 pc.(+1 extra)
Assembly Instructions 5/5
Wood Screw
Wall Screw
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight.
Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint
Drill 3/8” hole in wall
Top of unit
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Home Styles 5100-0063-62 Assembly Instructions

Type
Assembly Instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI