Home Styles 5180-184 Assembly Instructions

Type
Assembly Instructions
88 5180 04
Computer Hutch
Home Styles Consumer Assistance : www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
Hutch Unit Part List
IMPORTANT NOTE
.
Tools required for assembly : Phillips screwdriver
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
A.
Top
1 pc.
H.
Back Piece
1 pc.
L.
Back Panel
2 pcs.
B.
Side Panel
1 pc.
D.
Middle Panel
1 pc.
F.
Front Rail
1 pc.
G.
Back Stretcher
1 pc.
N.
Shelf
2 pcs.
O.
Shelf
1 pc.
P.
Door
1 pc.
Q.
Door
1 pc.
C.
Side Panel
1 pc.
E.
Middle Panel
1 pc.
M.
Back Panel
2 pcs.
I.
Back Piece
1 pc.
K.
Back Piece
2 pcs.
J.
Shelf
1 pc.
Hex Wrench
1 pc.
M6x30
Head Cap Bolt
6 pcs. (+1 extra)
Cam Lock
12 pcs.(+2 extra)
Cam Lock Screw
12 pcs.(+1 extra)
M4x15
Machine Screw
4 pcs.
Adjustable Pin
12 pcs. (+2 extra)
Steel Plate
Connector
2 pcs.
Door
Pull Handle
2 pcs.
M3.5x16
Wood Screw
8 pcs. (+1 extra)
Small
Hex Wrench
1 pc.
IMPORTANT
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in the safe place as you may need to tighten up the Head Cap Bolts in the future.
STEP 1
Assembly Instructions 2/3
Put Cam Lock Screws into the pre-drilled holes of Top (A) Side Panel (B),(C) Front Rail (I)
and tighten.
Attach Back Stretcher (H) to Side Panel (B) using Cam Lock.
Attach Back Piece (K) to Back Stretcher (H) and slide Back Panel (L) into place.
Attach Back Piece (I) to the unit and slide Back Panel (M) into place.
Attach Back Piece (K) to the unit and slide Back Panel (L) into Place.
Attach Back Stretcher (G) to the unit using Cam Locks.
STEP 2
B
G
H
K
K
I
Cam Lock
Cam Lock
L
L
M
M
B
C
Cam Lock Screw
F
A
A
N
N
O
P
Q
Cam Lock
Machine Screw
Pull Handle
Adjustable Pin
Head Cap Bolt
Assembly Instructions 3/3
J
STEP 3
Attach Shelf (J) to
the unit using Cam Locks.
Attach Middle Panel (D) and (E)
to shelf (J) with Head Cap Bolts.
Attach Front Rail (F) to the unit using Cam Lock.
Attach Side Panel (C) to the unit with Cam Locks.
D
E
F
C
Cam Lock
Head Cap Bolt
STEP 4
(Figure 2)
(Figure 1)
(Figure 4)
(Figure 3)
Turn the unit to
its upright position.
Place Top (A) onto the unit using Cam Locks
and Head Cap Bolts.
Insert Adjustable Pins into side panels and middle panels at the desired level
and Slide Shelf (N) and (O) into place.
Assemble Pull Handles to Door (P) and (Q)
with Machine Screws. (See Figure 1)
Attach Door (P) and (Q) to the side panels
by sliding the door lift hinges into
the side panel lift hinges. (See Figure 2)
Place the Hutch unit onto the Buffet unit. (See Figure 3)
Attach Steel Plate Connectors on the back of the units by inserting Wood Screws and tighten.
(See Figure 4)
HARDWARE LIST
Attention !
For safety reasons, please follow these additional instructions to
prevent the unit from tipping over.
Bracket
at the wall
Bracket
at the top
of the unit
Wood
Screw
Wall Screw
Plastic Belt
Top of unit
(Figure X)
M3.5x13
Wood Screw (short)
2 pcs.(+1 extra)
M3.5x40
Wall Screw (long)
2 pcs.(+1 extra)
Anchor
2 pcs.(+1 extra)
Bracket
4 pcs.(+1 extra)
Plastic Belt
2 pcs.(+1 extra)
Assembly Instructions
Place the unit at desired
location in room.
Drill two ¼” holes in wall at the appropriate
location.
Insert the Anchors into the wall holes and
attach the Brackets using Wall Screws.
Attach the Brackets at the pre-drilled holes
on the top of the unit using Wood Screws.
Use the Plastic Belt to secure the
Brackets on the unit to the Brackets on
the wall (See Figure X).
Put the tie end of the belt into the loop end
of the belt and pull until tight.
Drill two ¼” holes in wall
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Home Styles 5180-184 Assembly Instructions

Type
Assembly Instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI