Home Styles 5100-0071 Assembly Instructions

Home Styles
Brand
Home Styles
Model
5100-0071
Type
Assembly Instructions

This manual is also suitable for

88 5100 007
Buffet
Home Styles Consumer Assistance : www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
Part List
IMPORTANT NOTE
.
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
Tools required for assembly : Phillips screwdriver, Drill, 3/8” Drill Bit Level,
A.
Side Panel
1 Pc.
K.
Front Upright
2 Pcs.
L.
Fixed Shelf
1 Pc.
M.
Base
1 Pc.
N.
Leg
2 Pcs.
T.
Drawer
3 Pcs.
O.
Wine Grid
2 Pcs.
P.
Wine Grid
2 Pcs.
Q.
Shelf
2 Pcs.
R.
Door
1 Pc
S.
Door
1 Pc
B.
Side Panel
1 Pc.
C.
Middle Panel
1 Pc.
D.
Middle Panel
1 Pc.
E.
Back Panel
3 Pcs.
F.
Back Upright
2 Pcs.
G.
Back Stretcher
1 Pc.
H.
Back Stretcher
1 Pc.
I.
Front Stretcher
1 Pc.
J.
Front Stretcher
(Please refer to the last page of these
instructions for drawer assembly steps.)
M6x35
Head Cap Bolt
4 Pcs. (+1 extra)
Cam Lock
14 Pcs. (+2 extra)
Cam Lock Screw
14 Pcs. (+1 extra)
M3.5x13
Wood Screw (short)
for Base Drawer
12 Pcs. (+1 extra)
M3.5x16
Wood Screw
for Back Panel
12 Pcs. (+1 extra)
M4x25
Machine Screw
8 Pcs.
Small Hex Wrench
1 Pc.
M6x50
Head Cap Bolt (long)
8 Pcs. (+1 extra)
Cross Dowel
8 Pcs. (+1 extra)
M3.5x25
Wood Screw (long)
for Side Drawer
24 Pcs. (+1 extra)
Adjustable Pin
8 Pcs. (+2 extra)
Pull Handle
3 Pcs.
Knob
2 Pcs.
1 Pc.
Hex Wrench
1 pc.
Assembly Instructions 2/6
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
of Side Panel (A), Side Panel (B), Middle Panel
(C) and Middle Panel (D) and then tighten.
Shelf (L) with Cam Locks.
(See Figure 2)
A
B
C
C
D
D
L
Figure 1
Cam Lock Screw
Cam Lock
I
J
K
K
to Front Uprights (K).
Figure 2
Assembly Instructions 3/6
G
H
F
F
E
E
E
Head Cap Bolt (long)
Back Stretcher (H).
Slide Back Panels (E) into place.
Attach Back Stretcher (G) to
with Cross Dowers and Head Cap Bolts (long).
(See Figure 3)
Attach unit from Step 3 to unit .
Attach Side Panels (A) and (B) to unit
with Cam Locks.
A
B
N
N
M
Cam Lock
Figure 3
Head Cap Bolt (long)
Head Cap Bolt
Cross Dowels and Head Cap Bolts
(long).
Attach Legs (N) to Base (M) with
Head Cap Bolts.
Assembly Instructions /64
Place Top onto unit with Cam Locks.
Slide Drawers (T) into position.
Insert Adjustable Pins into side panels
and middle panels at the desired level.
Place Shelves (Q) into position.
Attach Knobs to Door (R) and (S)
with Machine Screws. (See Figure 4)
into the side panel lift hinges. (See Figure 5)
Assemble Wine Grids (O) and Wine Grids (P). (See Figure 6)
Slide Wine Grid into place.
To level the unit, adjust the adjustable levelers on the bottom of unit.
(See Figure 7)
Cam Lock Screw
Wood Screw
for back panel
O
O
P
P
Figure 6
Figure 7
Figure 5
panel into pre-drilled holes of back
panel.
Cam Lock
T
R
S
Q
Q
T
T
Attach Door (R) and (S) to side panels by sliding the door lift hinges
M3.5x13
Wood Screw
1 pc.(+1 extra)
Anchor
1 pc.(+1 extra)
Bracket
2 pcs.(+1 extra)
Tipover Restraint
1 pc.(+1 extra)
Hardware List
M3.5x40
Wall Screw
1 pc.(+1 extra)
Assembly Instructions 5/6
Wood Screw
Wall Screw
Attention!
To help reduce the risk of the unit tipping over, the Tipover Restraint be installed followingmust
these instructions exactly!
tie end
loop end
Place unit at desired location.
Drill a hole in wall3/8”
at the appropriate location.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole at top
of unit with Wood Screw.
Use Tipover Restraint to secure Bracket
on unit to Bracket on wall.
(See Figure X)
Put tie end of Tipover Restraint into loop end
of Tipover Restraint and pull until tight.
Figure X
Bracket
on wall
Anchor in wall
3/8” wall hole
Bracket at
top of unit
Tipover
Restraint
Top of unit
Drill 3/8” hole in wall
Assembly Instructions 6/6
Part List
T1.
Front Part
3 Pcs.
T2.
Back Part
3 Pcs.
T3.
Side Part
3 Pcs.
T4.
Side Part
3 Pcs.
T5.
Base Part
3 Pcs.
screwdriver and long Wood Screws (4X),
tighten halfway.
Attach T2 to T3 and T4 using long Wood
push T5 all the way forward so it meets T1.
(See Figure 2)
holes in T5, tighten screws.
(See Figure 4)
Drawer
T1
T1
T1
T2
T2
T3
T3
T3
T4
T4
T4
T5
T5
Figure 1
Figure 2
Figure 3
Figure 4
Tighten all screws used in drawer assembly.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Home Styles 5100-0071 Assembly Instructions

Home Styles
Brand
Home Styles
Model
5100-0071
Type
Assembly Instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents