Kathrein Euroline UFE 336 Operating instructions

Brand: Kathrein

Model: Euroline UFE 336

Type: Operating instructions

This manual is also suitable for

Operating Manual

DVB Satellite Receivers

UFE 335/335S - 336/336S

Order no.: 20210028/20210029 – 20210030/20210031

New.: 20210036/20210037 - 20210038/20210039

Preface

Dear Customer,

The following operating manual will help you obtain the best possible

use from the extensive features of your new satellite receiver.

We have written this operating manual as comprehensibly as possible

and as concise as necessary. A brief lexicon containing specialised

terms not easily translatable has been appended at the end of this

manual.

We have taken the environment into account with the mains switch.

Therefore, during longer pauses separate your receiver from the

mains in order to save energy. During short pauses, you should

switch the receiver to standby with the remote control, so the least

amount of energy is consumed.

We wish you a great reception and much enjoyment with your new

satellite receiver.

Your,

KATHREIN-Euroline



Team

Important notes

If you have any unexpected problems with your receiver, please

contact your specialist supplier.

With regard to the programme allocation of the satellites and trans-

ponders, changes always occur. In such cases, it is necessary to

carry out new programme settings, even though factory

pre-programming is always in accordance with the respective latest

developments. You can gather the details for the new setting from

teletext on SAT 1, the internet or relevant magazines.

Your receiver has been equipped with the latest software

at the factory. We are always trying to adjust the software to the

desires of our customers and the state-of-the-art technology. Refer to

section "Software and programme list update" for more information.

Please keep the original packaging for the purpose of returning

the unit!

UFE 335/335S FTA free-to-air programmes only (no CI-slot!)

UFE 336/336S CI free-to-air and encrypted programmes

(diagram on front page)

Contents

Preface.............................................................................................................................................................. 3

Contents ........................................................................................................................................................... 4

Safety instructions .......................................................................................................................................... 6

Extended absence / thunderstorms............................................................................................................ 6

Mains lead .................................................................................................................................................. 6

Cleaning ..................................................................................................................................................... 6

Children-at-play .......................................................................................................................................... 6

Repairs ....................................................................................................................................................... 6

Connections................................................................................................................................................ 6

Grounding................................................................................................................................................... 7

Place of installation..................................................................................................................................... 7

Ventilation................................................................................................................................................... 7

Moisture, exposure to sunlight, heat .......................................................................................................... 7

Mains supply............................................................................................................................................... 7

Connections, operation and displays............................................................................................................ 8

Operation.......................................................................................................................................................... 9

Local control................................................................................................................................................... 9

Functions of remote control......................................................................................................................... 10

Remote control command sets................................................................................................................. 10

Programme selection .................................................................................................................................... 12

Programme selection with the numerical buttons [0]-[9], [▲], [▼] and list .................................................. 12

„Last programme“ with the [E] button........................................................................................................... 12

„Zapper function“ with the [OK] and [◄] [▲] [►] [▼] buttons...................................................................... 12

Programme management with 10 favourite lists.......................................................................................... 13

Information for switching programmes......................................................................................................... 14

TV/radio switch-over .................................................................................................................................... 14

Volume settings............................................................................................................................................ 15

Language selection...................................................................................................................................... 15

Timer ............................................................................................................................................................ 16

EPG – Programme information (Basis navigator)........................................................................................ 17

Menu structure............................................................................................................................................... 19

Programmes................................................................................................................................................. 19

Favourite list ............................................................................................................................................. 19

Changing the names of the favourite lists ................................................................................................ 23

Programme pool....................................................................................................................................... 23

Antenna signal and reception parameters ............................................................................................... 24

Parental lock............................................................................................................................................. 24

Search.......................................................................................................................................................... 26

Satellite search......................................................................................................................................... 26

Transponder search ................................................................................................................................. 27

Manual entry (for experts) ........................................................................................................................ 27

Satellites....................................................................................................................................................... 27

Installation .................................................................................................................................................... 29

Time offset................................................................................................................................................ 29

Menu language......................................................................................................................................... 29

Selecting the font...................................................................................................................................... 29

Signal paths.............................................................................................................................................. 30

Picture format ........................................................................................................................................... 30

LNB settings ............................................................................................................................................. 30

DiSEqC



(Digital Satellite Equipment Control) ........................................................................................ 31

DiSEqC



................................................................................................................................................... 31

UFO

........................................................................................................................................................ 31

Download-over-air (Software updating via satellite)................................................................................. 32

CA (Conditional Access) = Encrypted programmes (only for UFE 336/336S!) ........................................... 33

Contents

General..................................................................................................................................................... 33

Reception of encrypted programmes ....................................................................................................... 34

Glossary ......................................................................................................................................................... 35

Technical data................................................................................................................................................ 36

Safety instructions

Important notes regarding operation

The following section contains important information relating to the

operation, place of installation and connection of the receiver.

Read these notes carefully before putting the unit into operation.

Extended absence / thunderstorms

Always switch the unit off via its mains switch located on the right on

the front panel during periods of extended absence or at the onset of

thunderstorms. This also applies to any other equipment which is

connected to the receiver.

However, take into account any possible timer programming, and

switch the unit on again in good time prior to the recording time.

Mains lead

Make certain that the mains lead (power supply lead) is undamaged.

Never put the unit into operation if the mains lead is damaged.

Cleaning

Withdraw the mains plug before cleaning the unit. Use a dry cloth for

cleaning. Clean the surface only, and nothing else.

On no account open the housing. There is a risk of electric shock if

components within the unit are touched!

Children-at-play

Pay attention that children do not insert objects into the ventilation

slots. There is a risk of mortal danger due to electric shock.

Repairs

Only have qualified specialists carry out repairs and adjustments to

your receiver. Unauthorised opening of the receiver and attempts at

repair entail loss of guarantee.

Unauthorised tampering with the device can jeopardise the electrical

safety of the receiver.

The manufacturer is not liable for accidents occurring to the user as a

result of opening the receiver.

Connections

The unit may be rendered inoperative or not work properly if the

connections are not wired up properly.

Safety instructions

Grounding

The parabolic antenna is to be grounded in accordance with regula-

tions. The relevant local and/or German VDE regulations are to be

complied with here.

Important notes for siting and installation.

Place of installation

Every electronic device generates heat. The rise in temperature,

however, lies within a safe range. Slight colour changes may occur to

sensitive furniture surfaces and veneers over the course of time due

to the constant effect of heat. In conjunction with treated furniture sur-

faces, the unit’s rubber feet can, likewise, give rise to changes in col-

our. Where necessary, place the unit on a suitable pad.

Ventilation

The heat which is generated in this unit is dissipated quite adequately.

Never install the receiver in a cabinet, shelf or rack with inadequate

ventilation. Never block the cooling slots on the unit.

Do not place objects on top of the unit. Maintain a clearance of at

least 10 cm above the unit, so that the heat generated within the unit

can disperse without obstruction.

Moisture, exposure to sunlight, heat

Protect the unit against moisture, drips and splashing.

Do not place the unit close to radiators nor expose it to direct sunlight.

Mains supply

Operate the receiver only with a mains voltage of 230V / 50 Hz.

First connect the antenna and the television set, before connecting the

receiver to the mains power supply and switching it on.

Connections, operation and displays

The following connections are found on the rear panel of the receiver:

230V / 50 Hz Connect the mains cable with the mains socket.

AUDIO TV L a. R Audio output, left and right channel for connection to a stereo system.

TV Connect the TV socket with your television set via the supplied Scart

cable.

VCR VCR Scart socket for connection of a video recorder.

SAT IF INPUT Sat IF input and output for LNB supply and control signals. Connect

the cable of your satellite system with this socket.

SAT IF OUTPUT IF signal output (Loop-through e.g. to an analogue receiver).

DATA INTERFACE RS 232 interface for serial data transmission for service.

0 modem cable (Pin 2 and 3 crossed, Pin 1, 4, 6-9 are not used).

Receiver: PC:

Pin 2 = RXD Pin 2 = RXD

Pin 3 = TXD Pin 3 = TXD

Pin 5 = GND Pin 5 = GND



Operation

Local control

Open (and close) the flap on the front panel of the unit by applying

pressure on the dotted area (left).

The local operation consists of the buttons, [STANDBY], [▲] and [▼]

for switching programmes (ascending/descending), as well as [ - ] and

[

+ ] for adjusting the volume.

To switch between radio and TV operation, press the [STANDBY] but-

ton and then within 1 second press the [ - ] button for radio or [ + ] for

TV operation.

The LED display shows the switch-over operation Radio/TV for a

second.

The receiver has an On/Off mains switch with mains separation.

The programme numbers are displayed on a 4-digit, green, 7-segment

display!

Display of TV programmes

Display of radio programmes

Display t = TV mode (and programme number of the satellite re-

ceiver)

The points appear when the unit is “muted.“

Display ‚Vcr‘:

The video/audio signal from the video recorder is automatically fed to

the television set during playback – also in standby.

Display ‚Vcr-‘: Through-connection in standby.

The unit is in standby and can be switched on by pressing the

[STANDBY] button.

P 9 9 9

r 2 5

t 1 2 3

P 2.3.4.

[

r t

]

V c r

V c r -

VOLUME CHANNEL

▼

▲

Functions of remote control

In standby, the receiver is switched on by pressing the red button or

the numerical buttons [0]-[9].

The [◄] [►] and [▲] [▼] buttons, which are arranged around the OK

button, possess the volume control function –/+ (Vol -/+) and the

programme selection function –/+ (Ch -/+) in normal operation.

Remote control command sets

The remote control can deal with two command sets. This enables the

parallel operation of two receivers independently in the same room

(not in connection with a twin receiver).

Note: Programme one receiver to command set 1 and the second to com-

mand set 2. Use the mains switch to activate receiver 1 and to deacti-

vate receiver 2.

Keep the button

“RC” pressed and then input the number “901” us-

ing the numbered keys.

In order to confirm the code and quit the remote control menu, press

“RC” again. Then press ““ to switch receiver 1 to standby and

deactivate the device using the mains switch.

Switch receiver 2 back on.

A description of the remote control

functions is integrated in the receiver’s

software. In order to call up these func-

tion descriptions, simply press the [RC]

button on the remote control and then

the button whose function is to be de-

scribed. The respective text is

displayed. Press the [RC] button once

more to exit the help menu.

Functions of remote control

Keep the button

“RC” pressed.

Use the numbered buttons to input “902”.

In order to confirm the code, press

“RC”, then switch receiver 2 to

standby by pressing

 and then switch back on again. Also switch

on receiver 1.

Keep the button

“RC” pressed and use the numbered buttons to

input “903”.

The remote control must point to the active receiver for the first two

settings.

You can now use the button

“RC” to switch between the command

sets A and B (toggle function), operating the two receivers alternately.

Command set 1 is the factory pre-setting.

If you are only operating one receiver and the active command set

has been switched by mistake so that the receiver can no longer be

operated, it is easy to switch the remote control back to command set

1. This process has already been described above.

Note: The remote control help (explanation of the remote control) is not dis-

played if you are operating two receivers!

Programme selection

Programme selection with the numerical buttons [0]-[9], [▲], [▼] and list

The programme setting is carried out by direct entry of the programme

number with the numerical buttons (0 is also a programme number).

With the [▲]/[▼] buttons, you can switch back/forward to the previous/

next programme.

After pressing the [OK] button twice, a list appears which is organised

according to programme numbers.

The desired programme can be called up with the [◄]/[►] and

[▲]/[▼] buttons and set by pressing the [OK] button. Exit the list by

pressing the [OK] button once more or the [E] button.

„Last programme“ with the [E] button

With the [E] button, you can switch between the last two set pro-

grammes.

„Zapper function“ with the [OK] and [◄] [▲] [►] [▼] buttons

If the current „desired programme“ is interrupted by advertisements,

many users „zap“ to a „substitute programme“ or to a second or third

programme. It often occurs that the user can’t find the way back to the

programme originally being watched.

The „zapper function” stores three further “substitute programmes,”

which were zapped to after the „desired programme.“ Only

programmes watched for at least 5 seconds can be saved.

The last 4 watched programmes can be directly called up by pressing

the [OK] button and then the [◄], [►], [▲] or [▼] button.

Programme selection

Programme management with 10 favourite lists

Digital television technology offers viewers a variety of

programmes. Depending on the number of received satellites, up to

2,000 TV and radio programmes are at one’s disposal.

In order to control such an enormous array of programmes, ten freely

definable favourite lists are available to the user, which allow clear

management and sorting of the programmes.

A favourite list is a list, in which any of the programmes selected from

a programme pool can be categorised.

The names of the lists are predefined at the factory comparable to the

following example. The names of the favourite list can be individually

changed. In each favourite list, the programme numbers P000 to P999

can be used.

Favourite list: Name Sorted programmes (example)

F0: GENERAL (e.g. All free-to-air programmes from the

programme pool)

F1: NEWS (e.g. PHOENIX, n-TV, N-24…)

F2: SPORT (e.g. DSF, EuroSport, Motors-TV)

F3: MUSIC (e.g. MTV, VIVA, VIVA 2…)

F4: TRAVEL (e.g. Travel-Channel…)

F5: SHOPPING (e.g. Home Shopping, QVC…)

F6: CHILDREN (e.g. KIKA and other programmes for

children)

F7: DIVERSE (e.g. All programmes, which are yet not

classified in a category)

F8: ABC (e.g. ...)

F9: XYZ (e.g. ...)

The desired programmes can be taken from the programme pool,

which contains all the programmes in alphabetical order, and copied

into one of the ten favourite lists.

All programmes from the programme pool are saved in the favourite

list F0 = GENERAL upon delivery. The favourite list F0 = GENERAL

contains all the programmes known thus far for satellite receivers.

Some of the programmes of the satellites, Astra 19.2° and EUTEL-

SAT/HOTBIRD, are already additionally contained in various favourite

lists.

The desired favourite list is selected by pressing the [F] button and

one of the assigned numerical buttons [0]-[9].

Programme selection

Information for switching programmes

This display bar appears every time you switch programmes – it is

displayed on the screen for approx. 3 seconds. It contains the follow-

ing information:

- Favourite list

- Programme slot and name

- If several audio and language channels are available, an „A“ is

displayed in the left-hand box next to the time (see item „select

language“).

- Current time

- Start and end times of the current programme

- Start and end times of the next programme

TV/radio switch-over

The switch-over to radio or TV is carried out with the [R] or [TV]

button. Both buttons effect the so-called switching voltage of the TV

Scart socket. If you also receive programmes via antenna or cable on

your TV set, you can switch between the programmes received via the

television set or the satellite receiver, provided that the switching

voltage from the television set is recognised and processed, with the

[TV] button.

Note: All the programme functions (Last programme, zapper function, fa-

vourite lists, programme lists and programme pool etc.) for TV can

also be separately used for 2,000 radio programmes.

Programme selection

Volume settings

a) The volume of the receiver can be set in 20 steps with the

[◄] or [►] button.

The current volume status appears in the programme display.

b) [

: ] Sound on/off (mute) – For „sound off,“ a respective OSD sym-

bol is displayed for ca. 2 seconds. The function „sound off“ is also

removed by pressing the volume button [◄] or [►].

Language selection

After pressing the [A] button, a menu appears for selecting the lan-

guage. The number of available languages depends on the

programme. The selection of the desired language is carried out as

usual with the [▼] or [▲] button.

After exiting the menu with the [E] button, the originally set language

remains active.

If you exit the menu with the [OK] button, the newly selected language

is saved.

Note: Please keep in mind that many programmes only offer one language.

However, there are radio stations which offer up to 20 or more „sub-

programmes.“ These programmes can be selected in the radio mode

with the [A] button.

L 2 0

Programme selection

Timer

The „Timer programming“ menu is called up by pressing the

[] button. Up to 8 timer events can be alternatively entered

in with TV or radio programmes.

Note: Keep in mind that the video recorder must be identically set to the

same recording times.

Note:

Please note that remote control commands are not accepted during

timer recording to assure that undesired OSD displays are not re-

corded. The volume is set to the maximum level during a recording.

Once a command is recognised from the remote control, „r E c“ ap-

pears on the programme display on the unit to indicate that a re-

cording is in progress.

The timer recording can only be cancelled prematurely by pressing

the [



] button. After the cancellation, „End“ is displayed. The unit now

operates as normal.

If the timer recording is started in standby, the unit switches back to

standby after the end of the recording.

[1-8] Select the next open entry field with the numerical buttons

[1]-[8] or with [▼] or [▲].

[►][◄] Select the entry field for {Date} {Start} {Stop} and {Pro-

gramme} one after the other (the entry position is highlighted

in white).

[OK] Activate the entry in the selected field by pressing [OK]

(the entry position is highlighted in black).

Enter in the respective event either directly with the numeri-

cal buttons [0]-[9] or by using the [►] [◄] buttons.

[OK] End the entry with [OK] and select the next entry field.

[ E ] After entering the {Date} {Start} {Stop} and {Programme},

you can confirm the entry and exit the timer menu by press-

ing the [E] button, or enter another event.

E n d

r E c

Programme selection

The data from the programme preview can be transferred to the re-

cording timer by pressing only one button. If the programme preview

is available, then select the desired programme and transfer the data

directly to the timer by pressing the [] button.

Deleting a timer programming:

[1-8] Select the timer line which you would like to delete with the

numerical buttons [1]-[8] or with [▼] or [▲],

[OK] and delete the programmed data by pressing the OK button.

Note: If you have accidentally deleted a line and would like to restore the

original information, exit the timer menu by pressing the [E] button

twice.

Note: Time and date are taken from the DVB data which is transmitted by

the broadcaster. Please correct the „time offset“ for for summer and

winter time in the „Installation“ menu.

For CET summer time = {+2 h}

For CET winter time = {+1 h}

Please keep in mind that some „exotic programmes“ do not transmit

the correct time.

Control the date and time in the „Timer programming“ menu, when

you carry out a programming.

EPG – Programme information (Basis navigator)

In the EPG (Electronic Programme Guide), information about the cur-

rent or following programmes is displayed.

The amount of this programme-accompanying information is deter-

mined by the respective programme provider and varies considerably

from programme to programme. Many programmes can be transmit-

ted without usable supplementary information (SI data).

It is just the same for the programme preview. Some programme pro-

viders do not transmit data. Others transmit a programme overview

with supplementary information covering several days.

Call up and exit the EPG using the [ i ] button.

a) Current and following programme

[ i ] Shows title, start and end of the current programme, and

information about the programme depending on the

programme provider.

[ i ] After pressing the button again, the title, start and end of the

following programme and supplementary information about

the programme, depending on the programme provider, are

displayed.

[ i ] Exits the programme information display.

[ E ] Immediately exits the programme information display.

b) Further programme preview and supplementary information

Programme selection

[ i ] Activates the basis navigator, displays information about cur-

rent programme.

[OK] Calls up the programme preview.

Depending on the programme provider, you can receive pro-

gramme lists for the current day or the next several days.

You can switch to the desired programme line-by-line or page-by-

page by using the [▼] [▲] or [►] [◄] buttons.

[OK] When you have selected the desired programme, you can

call up other detailed information by pressing the [OK] but-

ton. If supplementary information is not available, a

corresponding message is displayed.

If the text of the supplementary information exceeds the page, you

can scroll up and down line-by-line using the [▼] [▲] buttons.

With the [OK] or [ E ] button, exit the display of the

supplementary information and return to the programme preview once

more.

Menu structure

Programmes

Favourite list

With the [M] button, call up the main menu and then press the [OK]

button twice.

You can sort, exchange, copy and delete programmes – all in one

menu.

[ i ] Select one of the favourite lists 0-9.

[M] Select the satellites (e.g. ASTRA, EUTELSAT or other).

Menu structure

[TV] Select the programme source (e.g. NEW or ALL

programmes).

[▼] [▲] Select the targeted position in the favourite list (point of the

blue arrow).

[◄] [►] Select the programme from the source-programme list (in

the right window).

The programmes are arranged in alphabetical order.

[ : ] Places the current programme from the favourite list in the

centre field. (=withdraw).

[ A ] Copies the programme from the centre field to the favourite

list (= add).

[OK] Transfers the programme selected in the source-programme

list to the favourite list (left window) (= copy).

Exchanging Move the desired programme to the red bar with the [▼] [▲] buttons

or by direct entry of the programme number.

Page is loading ...

Kathrein Euroline UFE 336 Operating instructions

Brand: Kathrein

Model: Euroline UFE 336

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Kathrein Euroline UFE 336 Operating instructions

This manual is also suitable for

Kathrein Euroline UFE 336 Operating instructions

Related papers

Other documents