ID TECH Kiosk V Installation guide

ID TECH
Brand
ID TECH
Model
Kiosk V
Type
Installation guide

This manual is also suitable for

ID TECH Kiosk V is a versatile device suitable for mounting on the exterior of a kiosk structure. It features an NFC antenna for contactless payments and other applications, which should be kept at least 2 cm away from any metal surface for optimal performance. The Kiosk V requires four M3 screws for mounting and comes with a USB-Type C cable that should be routed through a dedicated rectangle hole for secure connection.

ID TECH Kiosk V is a versatile device suitable for mounting on the exterior of a kiosk structure. It features an NFC antenna for contactless payments and other applications, which should be kept at least 2 cm away from any metal surface for optimal performance. The Kiosk V requires four M3 screws for mounting and comes with a USB-Type C cable that should be routed through a dedicated rectangle hole for secure connection.

15 December 2022
Rev A
ID TECH
10721 Walker Street, Cypress, CA 90630-4720
Tel: (714) 761-6368 Fax (714) 761-8880
www.idtechproducts.com
Copyright© 2022 International Technologies and Systems Corporation. All rights reserved.
ID TECH Kiosk V Quick Installation Guide
Mounting the Kiosk V
Warning: The NFC antenna’s RF field is sensitive to the proximity of metal. If you must mount the Kiosk V in or
on a metal surface, note the following requirements to minimize the impact on RF performance:
• Kiosk V readers must not be installed behind any metal surfaces or materials that have metallic
content, which blocks the RF field.
• Mount Kiosk V readers a minimum of 2cm away from any metal surface.
• Keep the RF-emitting surface of Kiosk V readers at least 2cm from any metal.
Note: For safety reasons, make sure to mount the Kiosk V at a height no greater than two meters from the
floor.
Kiosk V Part# IDVK-5XX:
Note: The Kiosk V is post-compatible with Kiosk III and Kiosk IV dimensions. Posts are 36mm apart in the
lengthwise direction and 32mm apart widthwise. See drawing below.
15 December 2022
Rev A
ID TECH
10721 Walker Street, Cypress, CA 90630-4720
Tel: (714) 761-6368 Fax (714) 761-8880
www.idtechproducts.com
Copyright© 2022 International Technologies and Systems Corporation. All rights reserved.
Use the following instructions to mount the Kiosk V on the exterior of a kiosk structure:
1. Using the Drill Template below, locate and mark the (4) 3.5mm (0.138 inch) mounting holes.
Note: Verify the orientation of the Kiosk V before marking and drilling the holes. The rectangle hole should
be located towards the bottom of the mounting location to ensure that the Kiosk V is oriented correctly with
the LEDs at the top.
2. Using the Drill Template, locate and mark the 9.95mm*15.77mm (0.392inch*0.621inch) rectangle hole
(used for connecting the USB-type C cable to the Kiosk V).
3. Align the four M3 screws with the mounting holes and attach the Kiosk V to the outside surface.
4. Use the four screws to secure the Kiosk V to the outside surface of the kiosk. Make sure to tighten the
screws securely so that the Kiosk V does not move on the outside surface of the kiosk.
5. Route the end of the USB-Type C cable through the rectangle hole into the kiosk and tighten the two
M2 screws in the over mode of the USB-Type C cable to ensure the cable is locked reliably.
Installation Suggestions
• The Kiosk V is susceptible to RF and electromagnetic interference. Do not mounted the unit within 3 or 4
feet of large electric motors, computer UPS systems, microwave transmitters (Wi-Fi routers), anti-theft
devices, radio transmitters, communications equipment and so on.
• Close proximity of metal to the RF-emitting end of the NFC antenna can greatly reduce the NFC antenna’s
range.
  • Page 1 1
  • Page 2 2

ID TECH Kiosk V Installation guide

ID TECH
Brand
ID TECH
Model
Kiosk V
Type
Installation guide
This manual is also suitable for

ID TECH Kiosk V is a versatile device suitable for mounting on the exterior of a kiosk structure. It features an NFC antenna for contactless payments and other applications, which should be kept at least 2 cm away from any metal surface for optimal performance. The Kiosk V requires four M3 screws for mounting and comes with a USB-Type C cable that should be routed through a dedicated rectangle hole for secure connection.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents