Gainsborough 2909 Installation guide

Brand: Gainsborough

Model: 2909

Type: Installation guide

Below you will find brief information for 2800 2809, 2900 2909. These installation instructions detail how to fit the privacy adaptors to Gainsborough 2800 and 2900 series leversets. The instructions include how to prepare the door, install the latch, and assemble the internal and external parts of the door handle mechanism. Key steps include marking the door edge, drilling holes, chiseling for the faceplate, and correctly positioning the privacy snib. Ensure screws are tightened to a recommended torque of 2.5Nm. These are used to add privacy function to the door locks.

Below you will find brief information for 2800 2809, 2900 2909. These installation instructions detail how to fit the privacy adaptors to Gainsborough 2800 and 2900 series leversets. The instructions include how to prepare the door, install the latch, and assemble the internal and external parts of the door handle mechanism. Key steps include marking the door edge, drilling holes, chiseling for the faceplate, and correctly positioning the privacy snib. Ensure screws are tightened to a recommended torque of 2.5Nm. These are used to add privacy function to the door locks.

ORIGINATION CRM GSH 853 0413

AT 000

Fit here on door edge

BACKSET 60mm

BACKSET 70mm

Mark centre-line

of latch hole

FOLD HERE

Installation instructions for 2809 & 2909 Privacy Adaptors to suit

2800 & 2900 Series Leversets

(Purchase leverset and tubular latch separately)

NOTE: Carefully follow these instructions when installing.

Screws to be tightened to a recommended 2.5Nm torque.

Step 1.

Step 3.

Step 2.

• Mark and chisel door

edge for faceplate.

• Chisel the recess to a

depth that allows latch

to sit flush with door

edge. Use latch

faceplate

as a template.

• Insert latch & fasten

with wood screws

provided.

Prepare Internal Assembly

• Remove rosette covers (1) from both lever

assemblies.

• Remove alignment posts & tube nuts &

discard.

• Hold the privacy adaptor (2) against the

inside of internal lever-rosette (3)

by inserting the adaptor's spindle extension

(4) into square recess on inside

of internal lever.

• Ensure that the privacy snib (5) is in the

closed position.

Note: Emergency release arm must align

with slot (7) on external lever-rosette

assembly (8).

Prepare External Assembly

• Install spring (9) into square recess (10) in

external lever-rosette as shown.

• Insert emergency release bar (6) as shown

locating L shaped end into slot (7).

44mm hole

• Fold template where indicated.

• Position template on door edge

at desired latch height.

• Firmly hold template & mark

latch height & 5 hole centres

(4 off 9mm & 1 off 44mm)

at required backset.

• Measure door thickness and

mark centre.

• Drill 25mm latch hole.

Note: it is important to

drill this hole squarely.

• Drill Pilot holes - suggest 3mm,

then enlarge (4 off) 9mm holes

& (1 off) 44mm holes from

both sides of door.

55R1DOC03EV1 JAN 22

9mm hole (drill first)

Important Note

Drill 9mm holes before

44mm hole for ease of drilling

1

3

4

2

6

5

8

7

9

10

Snib must be closed

on installation

2

5

Fit here on door edge

1

Gainsborough 2909 Installation guide

Brand: Gainsborough

Model: 2909

Type: Installation guide

Below you will find brief information for 2800 2809, 2900 2909. These installation instructions detail how to fit the privacy adaptors to Gainsborough 2800 and 2900 series leversets. The instructions include how to prepare the door, install the latch, and assemble the internal and external parts of the door handle mechanism. Key steps include marking the door edge, drilling holes, chiseling for the faceplate, and correctly positioning the privacy snib. Ensure screws are tightened to a recommended torque of 2.5Nm. These are used to add privacy function to the door locks.

Download PDF

Related papers

Other documents