Dolmar PC-7612 V Owner's manual

Type
Owner's manual

This manual is also suitable for

GB Pressure water system Instruction Manual
F
Dispositif d’eau sous
pression
Manuel d’instructions
D Druckwassersystem Gebrauchsanleitung
I Sistema acqua di pressione Manuale di istruzioni
NL Waterspuitsysteem Gebruiksaanwijzing
E Sistema de agua a presión Manual de instrucciones
P
Sistema de água pressurizada
Manual de instruções
DK Trykvandssystem Brugervejledning
S Tryckvattensystem Bruksanvisning
NO Trykkvannssystem Bruksanvisning
FIN Painevesijärjestelmä Käyttöohje
GR Πιεστικό σύστημα νερού Εγχειρίδιο οδηγιών
PL Układ ciśnieniowy wody Instrukcja obsługi
LV Ūdens spiediena sistēma Lietošanas rokasgrāmata
EE Surveveesüsteem Kasutusjuhend
LT Vandens su slėgiu sistema Naudojimo instrukcija
HU Nyomóvízrendszer Használati útmuta
RO
Sistem de tăiere cu jet de a
Manual de instrucţiuni
SK Tlakový vodný systém Návod na obsluhu
CZ Tlakový vodní systém Návod k použití
UR
Система подачі води під
тиском
Інструкція з експлуатації
RU
Водоструйная система
высокого давления
Инструкция по эксплуатации
TR Basınçlı su sistemi Kullanım Kılavuzu
TH
ระบบอัดแรงดันน้ำ
ID Sistem air bertekanan Buku Petunjuk
VT
Hệ thống Thủy áp Hướng dẫn sử dụng
CS
压力水系统 使用说明书
KR
가압수 시스템 사용 설명서
PR
3
1 Quick-release coupling
2 Bolt
3 Clamp
4 Faucet lever
5 Tube
6 Front handle
7 Protection hood
8 Nozzle
9 Coupling
10 Coupling cap
11 Tube holder 1
12 Tube holder 2
English (Original instructions)
Explanation of general view (Fig. 1)
For Models PC-7612V, PC-7614V
Installing the pressure water system
CAUTION:
Before doing any work on the power cutter, always switch off the engine and disconnect the spark plug cap.
• Install the water connection as shown in Fig. 2. Fit clamp around the front handle and fasten with the bolt and
square nut.
• Pull the quick-release coupling from the water connection and connect it to the 1/2” supply line.
• Remove the cutting disk (see instruction manual of the power cutter).
• Insert the nozzles through the protection hood from the inside and put on couplings. Screw on and tighten the
coupling caps.
• Tube routing with the cutting assembly in the middle position, see Fig. 3.
Place the tube holder 2 in the hole in the belt cover and turn it by 90° angle to secure it.
Press in the tube at the tube holder 1 (mounted at factory shipment) and the tube holder 2.
• Tube routing with the cutting assembly in the outside position, see Fig. 4.
Press in the tube only at the tube holder 1.
IMPORTANT:
To avoid bending the tubes, be sure to position the couplings in accordance with Fig. 3 or 4 as appropriate.
• Install the cutting disc (see instruction manual).
• Connect the quick-release coupling to the supply tube.
NOTE:
• Thewaterowratecanbepreciselyadjustedwithvalve.


aita
anaptistinstraateliu
aitaorporation
njo ichiapan
www.dolar.co
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Dolmar PC-7612 V Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI