Aztech PoE Bullet 2MP IPC (Indoor) User guide

Brand: Aztech

Model: PoE Bullet 2MP IPC (Indoor)

Type: User guide

Thank you for using Kyla product! Please keep this Easy Start Guide for future use. For

support or help, visit kylaconnect.com

DISCLAIMER

Aztech Technologies Pte Ltd, its holding company and its associated companies

(hereinafter referred to collectively as “Aztech”) does not guarantee that adequate

warning or protection will be given, and disclaims all warranties and representations,

whether expressed, implied or otherwise statutory, concerning the product, including

without limitation any warranty of merchantability or tness for a particular purpose.

Aztech shall not be liable in any event for any consequential, indirect, incidental, special,

exemplary, punitive or enhanced damages resulting from the use, maintenance or

operation of the product.

The manufacturer makes no warranty or representation that the product constitutes a

re alarm system or is compliant with any requirements prescribed by any applicable

state or laws, codes, regulations and/or other specications that may be set out by

relevant authorities having jurisdiction (collectively referred to as “regulations”). You

shall be solely responsible for compliance with all regulations.

To the maximum extent permitted by applicable law, you agree to hold harmless and

indemnify, including legal fees, the manufacturer and their personnel against any third

party claims or nes by authorities that arise or are alleged to have arisen as a result of

negligent or intentional act or omission by you or breach by you of any the terms herein

or any violation of any regulations.

UNPACKING

Perform the following steps to unpack the camera

1. Inspect the package to make sure that it has not been damaged.If damage item

found, contact the local authorized Aztech Partner / Agent / Reseller.

2. Take all items out of the package and check whether any item is in defect

condition. If you nd damage item, contact the local authorized Aztech Partner

/ Agent / Reseller.

PACKAGE CONTENTS

Camera x1 Easy Start Guide x1 Warranty Card x1

Mounting Bracket x1 Expansion Pipe x3 Screw Pan x3

Allen Key x1

1 2

SAFETY INSTRUCTION

These instructions are intended to ensure that the user can use the camera correctly

to avoid danger or property loss. Please read this Guide carefully before using

the camera, and keep it properly for future reference. If the camera cannot work

normally or is damaged because the user does not follow the safety instructions, we

shall not assume any responsibility and warranty.

• Adopt power supply in the safety voltage range as per guidance.

• If camera does not work properly, please contact Aztech authorized partner /

agent / dealer or the nearest service

• Do not drop the camera or subject it to physical shock / impact.

• When cleaning the lens, please use a rubber dust blower or lens cleaning cloth

to remove the dirt. When cleaning transparent housing, please wipe gently

by using soft and dry clean cloth. Never apply any cleanser with ethanol or

benzene on it.

• Do not focus the camera lens on strong light such as the sun or incandescent

lamp. The strong light can cause overexposure or light leak (not camera

malfunction), which may shorten camera lifetime.

• Do not expose the camera in the environment not dened in the Guide.

Operating Enviorment

Working Voltage PoE (IEEE 802.3af)

Operating Temperature -20°C ~ 50°C

Operating Humidity ≤ 95% RH (non-condensing)

• While shipping / transporting the camera, pack it in the factory packing or

use materials with equivalent quality.

• When it is necessary to replace a part, please contact Aztech Authorized

Partner / Agent / Dealer in advance and replace the part with specied

model or part of the same model. We shall not assume any responsibility for

problems caused by unauthorized replacement.

• The camera is for indoor purpose. Do not install at outdoor or anywhere the

camera will be exposed to water.

NOTICE

The information in this document is subject to change without Note. Every effort has

been made in the preparation of this document to ensure accuracy of the contents,

but all statements, information, and recommendations in this document do not

constitute a warranty of any kind, express or implied. Aztech is not responsible for

printing or clerical errors.

3 4

INITIAL CONFIGURATION

1. Connect ethernet cable from camera (DC12 power jack) as alternative power

source to camera.

2. Visit the IP address of IP camera via Chrome / Edge. Activation page will require

user to create new password. Camera has no default password, without creating

password, camera will not be accessible / used.

Password length minimum 8 characters and maximum 32 characters. The

password must include uppercase, lowercase and numbers. Special character

is accepted but not compulsory.

3. Upon successful in password creation, Log-in page will be automatically loaded.

4. Live view page will be automatically loaded upon successful log-in verication.

5. If live view page is not loaded, please clear browser’s cache le and cookies

before revisit the page.

6. Network Conguration:

Recommended to set static IP for each camera.

• Enterprise customer: It is recommended to consult with IT department to

select available IP address, subnets mask, gateway and DNS address.

• Residential customer: All this information can be found in internet router.

7. Time Conguration:

• Time zone selection to camera registered region.

• Time format supported: 12-hours and 24-hours

• Date format supported: YYYYMMDD, MMDDYYYY and DDMMYYYY

• NTP server address - if the user preferred to have automatically updated

time from NTP local server (Free NTP server available in Google Search).

8. Video Conguration:

• FPS (Frame Per Seconds)

It is recommended to use as high as supported by camera (Aztech’s

camera support up to 30FPS). Nonetheless, if the installation environment

bandwidth is limited, user is recommended to set as low as 15FPS – 20FPS.

• Bitrate support manual setting or auto setting.

for 2MP recommended to use 2048Kbps (2Mbps) or lowest 1024Kbps

(1Mbps) based on H.265 video compression

• Resolution recommended for main stream is as high as camera

supported and set sub stream to lower resolution to reduce bandwidth

during live view.

• Video compression: H.264 and H.265

H.265 is higher video compression with lower bitrate. As international

standard, H.265 only need half bandwidth and storage compared to H.264.

Example: H.264 2048Kbps 30FPS is about the same as H.265 1024Kbps 30FPS

9. Display Conguration:

• Display attribute to be adjusted according to environment situation and

condition

• IRCut Mode default is Auto

• If installation is wall mount, the user will need to toggle “OverTurn” feature

to rotate the camera view 180

• Aztech camera support 2 OSD: timestamp and location name. to activate,

the user needs to toggle the timestamp and location button.

5 6

CAMERA INSTALLATION

7 8

EASY START GUIDE

IR BULLET NETWORK CAMERA

2. Insert the Lan cable into the

connector.

3, Hold the side buttons of the camera,

then plug the base to the bracket.

For surface wiring,

take off the plastic part

1. Screw the wall mount bracket

to the wall/celling.

Plastic

Anchor

4. Adjust the camera angles

vertically and horizontally.

5. Tighten the screws with allen key.

Aztech PoE Bullet 2MP IPC (Indoor) User guide

Aztech PoE Bullet 2MP IPC (Indoor) User guide

Aztech PoE Bullet 2MP IPC (Indoor) User guide

Related papers

Other documents