Astria Fireplaces DRL30 Instruction Sheet

Brand: Astria Fireplaces

Model: DRL30

Type: Instruction Sheet

This manual is also suitable for

Sirius

Astria Fireplaces DRL30 is a direct-vent gas fireplace that offers a sleek and modern design, providing supplemental heat and ambiance to your living space. It features a millivolt ignition system that allows for reliable operation even during power outages, and a variable flame height adjustment for precise control over the fire's intensity. The DRL30 also includes a remote control for added convenience, allowing you to adjust the flame height and turn the fireplace on or off from the comfort of your seat.

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE REPRESENTATIVE AND ARE NOT DRAWN TO SCALE.

www.IHP.US.com

P900253-00

ASSEMBLY AND INSTALLATION INSTRUCTIONS FOR SURROUND KITS

FOR USE ON CONTEMPORARY LINEAR VIEW DIRECT-VENT GAS FIREPLACES

P/N 900253-00 Rev. NC 10/2014

HEARTH PRODUCTS

KITS AND ACCESSORIES

SURROUND KIT

FOR CONTEMPORARY LINEAR VIEW GAS FIREPLACES

[MODEL NUMBERS SIRIUS42TEN/P, SIRIUS54TEN/P, DRL3042TEN/P AND DRL3054TEN/P]

Figure 1: Contemporary Linear View Surround

Size Finish Cat. No. Model No.

42 in. Surround Black Satin H8654 LDV42-SB

54 in. Surround Black Satin H8652 LDV54-SB

Table 1: Surround Kits for Contemporary Linear View Gas

Fireplaces

KIT CONTENTS

• Top surround section (1)

• Bottom surround section (1)

• Side surround sections (2)

• Side support bars (2)

• #10-16 x 3/8 Hex-head sheet metal screws (17)

RIGHT Side

Surround Section

(rear view)

LEFT Side

Surround Section

(rear view)

Side Support Bars

Top Surround Section (rear view)

Bottom Surround Section (rear view)

Figure 2: Kit Contents

REQUIRED TOOLS

• 3/8 in. Hex-head nut driver

• Safety glasses

• Protective work gloves

GENERAL INFORMATION

This document contains instructions for assembling and

installing the enclosed surround for use with Elite™ Linear View

direct-vent gas ﬁreplaces manufactured by Innovative Hearth

Products.

NOTICE

•READ ALL STEPS BEFORE STARTING INSTALLATION.

•LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE.

•All warnings, precautions, and instructions in the Installation

Instructions and Care and Operation Instructions provided with the

appliance also apply to these instructions.

•If you encounter any problems, need clarification of these

instructions,orarenotqualiedtoproperlyinstallthiskit,contact

your local distributor or dealer.

NOTE:For easier installation, remove the ﬁreplace front

door before installing the surround. Refer to the Care and

Operation Instructions (PN 900079-00) for more information.

NOTE: Make sure you have the correct kit and all required

parts before starting installation.

INSTALLATION INSTRUCTIONS

NOTE: Ensure the work surface is free of debris that

may damage the surround ﬁnish. Any such DAMAGE

IS NOT COVERED by the manufacturer's warranty.

When the work surface is ready, peel the clear

protective plastic ﬁlm from all surround sections.

Step 1. Lay out the parts of the surround face down. Arrange

the parts as shown in Figure 3 (the surround must be

assembled from the back side)

Step 2. Insert the side support bar under the lip of the edge of

thesidesurroundsection,asshowninFigure 4.

NOTE: The side support bar has small notches that

face the front of the surround.

Step 3. Slide the upper end of the side support bar under the

lip of the top surround section (Figure 5).

DANGER

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL COOLED.

NEVER ALLOW CHILDREN TO TOUCH GLASS.

• Install only when ﬁreplace is OFF and COLD.

• Fireplace surfaces get EXTREMELY HOT!

• The glass on the front of the ﬁreplace reaches EXTREMELY HIGH

temperatures and can cause severe burns if touched. Even after the

gas is turned off, ﬁreplace surfaces remain extremely hot.

• Keep children away from an operating ﬁreplace. Closely supervise

children in any room where a ﬁreplace is operating to prevent contact

with glass.

INNOVATIVEHEARTHPRODUCTS•LINEARVIEWDIRECT-VENTGASFIREPLACE•REQUIREDANDOPTIONALACCESSORIES

Printed in U.S.A.

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE REPRESENTATIVE AND ARE NOT DRAWN TO SCALE.

P/N 900253-00 Rev. NC 10/2014 P900253-00

1508 Elm Hill Pike, Suite 108

Nashville, TN 37210

IHP.US.com

Figure 3: Lay Out the Surround Parts

Figure 4: Insert Side Support Bar

Step 4. Align the two holes in the upper lip of the side

surround section with the corresponding holes in the

topsurroundsection,andsecureusingtwo(2)ofthe

provided #10-16 x 3/8 hex-head screws (Figure 6).

Step 5. Repeat Step 1 through Step 4 for the other side of

the surround.

Step 6. Attach the bottom surround section in the same

manner,andsecureusingfour(4)oftheprovided

#10-16 x 3/8 hex-head screws (2 per side)

Figure 5: Align Side Support Bar with Surround Section

Figure 6: Attach Side Support to Surround Section

Step 7. Carefully attach the assembled surround to the

ﬁreplace using nine (9) of the provided #10-16 x 3/8

hex-headscrews(3atthetopand6atthebottom),as

shown in Figure 7,takecarenottoscratchordamage

the ﬁnish on the surround.

Step 8. Attach the Modesty Panel with three magnets (see

Figure 8).

Figure 7: Attach the Assembled Surround to the Fireplace

Figure 8: Placing Magnets for Modesty Panel

Astria Fireplaces DRL30 Instruction Sheet

Brand: Astria Fireplaces

Model: DRL30

Type: Instruction Sheet

This manual is also suitable for

Sirius

Download PDF

report

Astria Fireplaces DRL30 Instruction Sheet

This manual is also suitable for

Astria Fireplaces DRL30 Instruction Sheet

Related papers

Other documents