Alarm.Com ADC-V700X Installation guide
- Category
- Security cameras
- Type
- Installation guide
Questions? Contact Alarm.com Dealer Support at
1.866.834.0470 or [email protected].
Alarm.com, Inc. © 2000 - 2010 All rights reserved. www.alarm.com
INSTALL
Required Items for Installation:
l
Camera and power adapter (included)
l
Broadband (Cable, DSL, or Fiber-optic) Internet
connection with router
l
Windows or Mac computer
l
Login/password for the customer account
l
RJ45 female/female coupler (included)
l
Ethernet cable for the camera (connect to camera via
included coupler)
Install the Camera(s):
1. Connect the camera’s Ethernet cable to the network router using the included RJ45 female/female coupler and a standard
Ethernet cable.
2. Apply power (from a non-switched outlet)
to the camera using the AC adapter or a
Power over Ethernet (PoE) injector.
3. From a computer on the same network as the
camera, log into the customer’s account at
www.alarm.com.
4. Type www.alarm.com/addcamera into
the browser’s address bar and follow the
on-screen instructions to add the camera
to the Alarm.com account.
InstallatIon GuIde
Outdoor Night-Vision IP Camera (ADC-V700X)
Questions? Contact Alarm.com Dealer Support at
1.866.834.0470 or [email protected].
Alarm.com, Inc. © 2000 - 2010 All rights reserved. www.alarm.com
INSTALL
Hardware Installation:
Secure the camera to the wall/ceiling using the supplied camera stand. Note: If camera
is ceiling-mounted (with logo upside down), you will need to invert the camera image so
live and recorded video does not appear upside down. This setting can be changed on
the Camera Image Settings page.
The camera comes with a pre-installed cable, but it can be replaced with a custom cable
by using the spare 3-hole, water-tight connector that is included with the camera.
Weatherproofing the Camera:
The camera is weather-sealed at the factory, but if it is opened in a
humid environment the supplied silica gel pack should be installed to
prevent fogging of the lens.
1. Loosen the black plastic cable nut, and then pull out the black
plastic cable seal.
2. Unscrew the metal back cover of the camera body.
3. Remove the silica gel pack from its plastic pouch, but do not open
the silica pack itself. Secure the silica gel pack to the inside of the
camera housing using double-sided adhesive.
4. Make sure all cable lines are securely connected.
5. Tighten the back cover, rubber seal, and black plastic cable nut.
Physical Details:
Notes:
The Infrared LEDs provide illumination of up to 30ft for
nighttime video viewing and recording.
Operating temperature range is -4 to +122 F
(-20 to +50 C).
Power over Ethernet – PoE (Optional)
This camera model is PoE-compatible, allowing it to be powered by the Ethernet cable if
connected to a PoE power injector installed at the network router.
With this installation conguration, the camera’s power wire and AC power adapter are not used.
-
1
-
2
Alarm.Com ADC-V700X Installation guide
- Category
- Security cameras
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Alarm.Com ADC-V720W Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Legrand PW1020 User guide
-
ALARM COM ADC-VC727P Installation guide
-
ALARM.COM TYCO Alarm.com ADC-V721W-I Outdoor Wireless IP Camera User manual
-
Interlogix Simon XT/XTi GSM Module v4 Installation guide
-
-
-
-
GE superbus 2000 concord 4 gsm module User manual
-
DSC PowerSeries Neo 3G8080 Installation guide
-
Alarm ADC-V723 User guide
