STA X X
Installation Instructions
™
© 2021 Innovative Ergonomic Solutions REV A
Innovative Ergonomic Solutions
800 524 2744
customerservice@team-ies.com
team-ies.com
HAT Collective
408 437 8770
cs@hatcollective.com
hatcollective.com
STX-2-XXX-SLD-8510-YYY
PAGE 1 OF 21
A Top Down Mount 1x
8524
B Dimpled Pole 1x
110607-20
C Stackable Mount 2x
413054
D Pole Collar 1x
113332
E Pole Clip 1x
113449
F Dog Washer for Articulating Arms 2x
113704
G Rotation Stop for Articulating Arms 2x
113705
H M6 x 1mm Phillips Pan Head Screw 2x
105304
I Quick Connect VESA Plate 2x
114808
J M4 x 12mm Phillips Pan Head Screw 8x
701153
K 9-inch Beam Assembly 1x
416088
L Dog Washer 2x
105189
M 10-32 x 3/8" FPhMS w/Lock Patch 2x
705198
N Laptop Holder 1x
8510
O Split Washer 4x
701910
P Coupling Nut 4x
716187
Q Monitor Tilter 1x
8500 Tilter
R Pole Cap 1x
105195
S Cable Clip 1x
104533
T Cable Cap 2x
114810
U Forearm Cable Cap 2x
115584
V 1/8" Allen Wrench 1x
701312
W 3/32" Allen Wrench 1x
700146
X 7/32" Allen Wrench 1x
701127
Y 4mm Allen Wrench 1x
709877
Z* M8 x 95mm SCHS 1x
716061
AA* Spacer 1x
701544
BB* Lock Nut 1x
710015
* Included with optional thru-desk kit only, model # 8524-TM-CK (sold separately).
PARTS LIST
PAGE 2 OF 21
X
A
Desk thickness
up to 1.5" (3.8 cm)
Desk thickness
up to 1.5" (3.8 cm)
iIf the monitor arm or pole does not easily fit into the
mount, remove the bushing from the mount and place
it on the monitor arm or pole and press firmly back
into the mount.
OR
1 2
2a 2b 2c
7/32"
DESK CLAMP CONFIGURATION
OR
PAGE 3 OF 21
3 4
THRU-DESK CONFIGURATION*
X
Z
AA
BB
7/32"
Desk thickness
up to 1.5" (3.8 cm)
* Thru-desk kit required, model # 8524-TM-CK (sold separately).
PAGE 4 OF 21
i
IMP ORTANT:
When inserting
pole into mount,
the dimples
should be aligned
perpendicular to
the rear edge of
mounting surface.
Dimples
5
B
C
D
W
3/32"
PAGE 5 OF 21
6
E
PAGE 6 OF 21
F
G
7
H
i
OR
iIMP ORTANT:
Install part (G) in the
orientation as shown to
the left. When washer,
part (G), is installed
correctly, the arms will
not rotate past the back
of the mount.
F
PAGE 7 OF 21
I
K
L
M
8
PAGE 8 OF 21
M
9
L
PAGE 9 OF 21
10
J
I
PAGE 10 OF 21
11
PAGE 11 OF 21
12
Q
L
M
PAGE 12 OF 21
13
N
I
O
P
PAGE 13 OF 21
14
PAGE 14 OF 21
15
PAGE 15 OF 21
16
PAGE 16 OF 21
17
PAGE 17 OF 21
18
X
7/32"
i
In some instances, an additional
counterbalance adjustment may
be needed to allow the arm’s
instant height adjustment function
to work properly.
If your arm is not staying in position
after performing step 17, tighten
the adjustment screw with a
1/8" Allen wrench.
V
1/8"
Optional Adjustment
2x
PAGE 18 OF 21
4 mm
Y
19
V
1/8"
PAGE 19 OF 21
20
2x
PAGE 20 OF 21
Page is loading ...
/
